TPAIR-16T Network Card Settings and Configuration
INTELLICOM, INC.
TPAIR-16T
NIC Type | Ethernet |
Transfer Rate | 10Mbps |
Data Bus | 16-bit ISA |
Topology | Star |
Wiring Type | Unshielded twisted pair AUI transceiver via DB-15 port |
Boot ROM | Available |
I/O BASE ADDRESS | ||
Address | A5 | A6 |
300 - 31Fh | Pins 1 & 2 closed | Pins 1 & 2 closed |
320 - 33Fh | Pins 1 & 2 closed | Pins 2 & 3 closed |
340 - 35Fh | Pins 2 & 3 closed | Pins 1 & 2 closed |
360 - 37Fh | Pins 2 & 3 closed | Pins 2 & 3 closed |
BOOT ROM ADDRESS | ||||
Address | A14 | A16 | A17 | |
| » | C8000h | Closed | Closed | Closed |
CC000h | Open | Closed | Closed | |
D8000h | Closed | Open | Closed | |
DC000h | Open | Open | Closed | |
E8000h | Closed | Closed | Open | |
EC000h | Open | Closed | Open | |
INTERRUPT REQUEST | |||||
IRQ | JP1A | JP1B | JP1C | JP1D | |
2/9 | Closed | Open | Open | Open | |
| » | 3 | Open | Closed | Open | Open |
4 | Open | Open | Closed | Open | |
5 | Open | Open | Open | Closed | |
DMA CHANNEL | |||||
Channel | JP1E | JP1F | JP1H | JP1I | |
| » | Disabled | Open | Open | Open | Open |
DMA1 | Closed | Open | Closed | Open | |
DMA3 | Open | Closed | Open | Closed | |
CABLE TYPE | |
Type | JP2A - JP2F |
Shielded/Unshielded twisted pair | Pins 2 & 3 closed |
AUI transceiver via DB-15 port | Pins 1 & 2 closed |
LINK INTEGRITY TEST | ||
Setting | JP3 | |
| » | Enabled | Pins 2 & 3 closed |
Disabled | Pins 1 & 2 closed | |
Note:The link integrity test is valid only when the cable type is shielded/unshielded twisted pair. If using a LattisNet network Link Integrity must be disabled (JP3 Pins 1 & 2 closed) | ||
SIGNAL QUALITY ERROR (SQE) TEST | ||
Setting | JP4 | |
| » | Enabled | Pins 2 & 3 closed |
| Disabled | Pins 1 & 2 closed | |
Note:Signal Quality Error (SQE) is an internal test of the collision circuitry and path. If using a LattisNet network SQE must be disabled (JP4 Pins 1 & 2 closed)
| ||
BOOT ROM | ||
Setting | JP18 | |
| » | Disabled | Pins 2 & 3 closed |
Enabled | Pins 1 & 2 closed | |
FACTORY CONFIGURED SETTINGS | |
Jumper | Setting |
JP1G | Open |
DIAGNOSTIC LED(S) | ||
LED | Status | Condition |
LED1 | On | Data is being transmitted |
LED1 | Off | Data is not being transmitted |
LED2 | On | Twisted pair network connection is good |
LED2 | Off | Twisted pair network connection is broken |
LED3 | On | Data is being received |
LED3 | Off | Data is not being received |
LED4 | On | Card is transmitting constantly (Jabber) |
LED4 | Off | Normal operation |
LED5 | On | Collision detected on network |
LED5 | Off | No collisions detected on network |
My Books
