WS-2814JS6 (INTERNAL) modem/telephone/ISDN Settings and Configuration

Card Type	Modem (synchronous/asynchronous)
Chipset	Sierra
I/O Options	Voice, microphone in, speaker out
Maximum Data Rate	28.8Kbps
Maximum Fax Rate	14.4Kbps
Data Bus	8/16-bit ISA
Fax Class	Class I & II
Data Modulation	Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.32, V.32bis, V.34
Fax Modulation	ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression	MNP5, V.42, V.42bis

CONNECTIONS
Function	Label	Function	Label
Telephone line in	CN1	Speaker out	CN3
Telephone line out	CN2	Microphone in	CN4

INTERRUPT SELECTION
Setting	JP6/A	JP6/B	JP6/C	JP6/D	JP6/E	JP6/F
í IRQ3	Open	Open	Open	Open	Open	Closed
IRQ4	Open	Open	Open	Open	Closed	Open
IRQ5	Open	Open	Open	Closed	Open	Open
IRQ10	Open	Open	Closed	Open	Open	Open
IRQ11	Open	Closed	Open	Open	Open	Open
IRQ12	Closed	Open	Open	Open	Open	Open

SERIAL PORT ADDRESS SELECTION
Setting	JP6/G	JP6/H
3F8h (COM1:)	Open	Open
2F8h (COM2:)	Open	Closed
3E8h (COM3:)	Closed	Open
í 2E8h (COM4:)	Closed	Closed

SUPPORTED STANDARD COMMANDS

Basic AT Commands

+++, ‘comma’, A/

A, B, D, E, H, L, M, O, P, Q, T, V, X, Y, Z

&C, &D, &F, &M, &S, &T, &V, &W, &Y, &Z

Extended AT Commands

\C, \G, \N, \Q, \V, \X

%A, %C, %D, %Q

S-Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S12, S18, S25, S26, S38

Note: See MHI documentation for complete information.

AUTO-FALL FORWARD/FALLBACK
Type:	Configuration
Format:	AT [cmds] &An [cmds]
Description:	Selects whether the modem will automatically fall forward or back in response to line conditions.
Command	Function
&A0	Auto-fall forward/fallback disabled.
&A1	Auto-fall forward/fallback enabled.

DISPLAY INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested about the modem.
Command	Function
I0	Reports product identification code.
I1	Reports ROM checksum.
I2	Tests and reports ROM checksum.
I3	Reports firmware revision and model ID.
I4	Reports configuration ID.

LOCAL SERIAL PORT SPEED
Type:	Configuration
Format:	AT [cmds] \Tn [cmds]
Description:	Sets the speed of the local serial port.
Command	Function
\T0	Auto-detect serial port speed.
\T1	Use speed of last command.
\T2	Set speed to 300bps.
\T3	Set speed to 1200bps.
\T4	Set speed to 2400bps.
\T5	Set speed to 4800bps.
\T6	Set speed to 7200bps.
\T7	Set speed to 9600bps.
\T8	Set speed to 12Kbps.
\T9	Set speed to 14.4Kbps.
\T10	Set speed to 16.8Kbps.
\T11	Set speed to 19.2Kbps.
\T12	Set speed to 21.6Kbps.
\T13	Set speed to 24Kbps.
\T14	Set speed to 26.4Kbps.
\T15	Set speed to 28.8Kbps.
\T16	Set speed to 38.4Kbps.
\T17	Set speed to 57.6Kbps.
\T18	Set speed to 76.8Kbps.
\T19	Set speed to 115.2Kbps.
\T20	Set speed to 128Kbps.

PROTOCOL
Type:	Configuration
Format:	AT [cmds] &Hn [cmds]
Description:	Selects the modulation protocol that the modem will use.
Command	Function
&H0	Use V.34 with fallback to lower protocols.
&H1	Use V.34 only.
&H2	Use V.32bis with fallback to lower protocols.
&H3	Use V.32bis only.
&H4	Use V.32 with fallback to lower protocols.
&H5	Use V.32 only.
&H6	Use V.22bis only.
&H7	Use V.22 only.
&H8	Use Bell 212A only.
&H9	Use Bell 103A only.
&H10	Use V.21 only.

TRELLIS CODING
Type:	Configuration
Format:	AT [cmds] &Un [cmds]
Description:	Selects whether the modem will use trellis coding.
Command		Function
í &U0		Trellis coding enabled.
&U1		Trellis coding disabled.