NP600A Network Card Settings and Configuration

RACAL-INTERLAN, INC.

NP600A

NIC Type
Ethernet
Transfer Rate
10Mbps
Data Bus
16-bit ISA
Topology
Linear Bus
Wiring Type
AUI Transceiver via DB-15 port
RG-58A/U 50ohm coaxial
Boot ROM
Not available

I/O BASE ADDRESS JUMPER SETTINGS
Address
A3
A4
A5
A6
A7
A8
A9
200h
1 & 2
1 & 2
1 & 2
1 & 2
1 & 2
1 & 2
2 & 3
208h
2 & 3
1 & 2
1 & 2
1 & 2
1 & 2
1 & 2
2 & 3
210h
1 & 2
2 & 3
1 & 2
1 & 2
1 & 2
1 & 2
2 & 3
218h
2 & 3
2 & 3
1 & 2
1 & 2
1 & 2
1 & 2
2 & 3
220h
1 & 2
1 & 2
2 & 3
1 & 2
1 & 2
1 & 2
2 & 3
3D8h
2 & 3
2 & 3
1 & 2
2 & 3
2 & 3
2 & 3
2 & 3
3E0h
1 & 2
1 & 2
2 & 3
2 & 3
2 & 3
2 & 3
2 & 3
3E8h
2 & 3
1 & 2
2 & 3
2 & 3
2 & 3
2 & 3
2 & 3
3F0h
1 & 2
2 & 3
2 & 3
2 & 3
2 & 3
2 & 3
2 & 3
3F8h
2 & 3
2 & 3
2 & 3
2 & 3
2 & 3
2 & 3
2 & 3
Note: A total of 127 memory base address settings are available. The switches are a binary representation of the hexadecimal addresses. Jumper A3 is the Least Significant Bit and Jumper A9 is the Most Significant Bit. The jumpers have the following decimal values: Jumper A3=8, A4=16, A5=32, A6=64, A7=16, A8=256, A9=512. Add the values of the jumpers with pins 2 & 3 closed to obtain the correct memory address. (On=pins 2 & 3 closed, Off=pins 1 & 2 closed)

CABLE TYPE SELECTION
Cable Type
NTS
AUI Transceiver via DB-15 port
Configuration 1
RG-58A/U 50ohm coaxial
Configuration 2

INTERRUPT SELECTION
IRQ
JP1
JP2
JP3
JP4
JP5
3
Closed
Open
Open
Open
Open
5
Open
Closed
Open
Open
Open
9
Open
Open
Closed
Open
Open
11
Open
Open
Open
Closed
Open
15
Open
Open
Open
Open
Closed

DMA CHANNEL SELECTION
Channel
CH7
CH5
CH1
CH3
DMA7
Closed
Open
Open
Open
DMA5
Open
Closed
Open
Open
DMA1
Open
Open
Closed
Open
DMA3
Open
Open
Open
Closed

DIAGNOSTIC LED(S)
LED1 (Red)
LED2 (Green)
Condition
Off
On
Network connection is good
On
On
Kernal and hardware failure
On
Off
Hardware failure
Off
Off
network connection is broken
Note: LED3 is lit only when UTP network connection is good

FACTORY CONFIGURED SETTINGS
Jumper
Setting
W15-18
Pins 2 & 3 closed

Headaches Begone! A Systemic Approach To Healing Your Headaches

Don't Let Your Bike Seat Ruin Your Sex Life Book

NP600A Network Card Settings and Configuration

Search

My Books

Discover

NIC Type	Ethernet
Transfer Rate	10Mbps
Data Bus	16-bit ISA
Topology	Linear Bus
Wiring Type	AUI Transceiver via DB-15 port RG-58A/U 50ohm coaxial
Boot ROM	Not available

I/O BASE ADDRESS JUMPER SETTINGS
Address	A3	A4	A5	A6	A7	A8	A9
200h	1 & 2	1 & 2	1 & 2	1 & 2	1 & 2	1 & 2	2 & 3
208h	2 & 3	1 & 2	1 & 2	1 & 2	1 & 2	1 & 2	2 & 3
210h	1 & 2	2 & 3	1 & 2	1 & 2	1 & 2	1 & 2	2 & 3
218h	2 & 3	2 & 3	1 & 2	1 & 2	1 & 2	1 & 2	2 & 3
220h	1 & 2	1 & 2	2 & 3	1 & 2	1 & 2	1 & 2	2 & 3
3D8h	2 & 3	2 & 3	1 & 2	2 & 3	2 & 3	2 & 3	2 & 3
3E0h	1 & 2	1 & 2	2 & 3	2 & 3	2 & 3	2 & 3	2 & 3
3E8h	2 & 3	1 & 2	2 & 3	2 & 3	2 & 3	2 & 3	2 & 3
3F0h	1 & 2	2 & 3	2 & 3	2 & 3	2 & 3	2 & 3	2 & 3
3F8h	2 & 3	2 & 3	2 & 3	2 & 3	2 & 3	2 & 3	2 & 3
Note: A total of 127 memory base address settings are available. The switches are a binary representation of the hexadecimal addresses. Jumper A3 is the Least Significant Bit and Jumper A9 is the Most Significant Bit. The jumpers have the following decimal values: Jumper A3=8, A4=16, A5=32, A6=64, A7=16, A8=256, A9=512. Add the values of the jumpers with pins 2 & 3 closed to obtain the correct memory address. (On=pins 2 & 3 closed, Off=pins 1 & 2 closed)

CABLE TYPE SELECTION
Cable Type	NTS
AUI Transceiver via DB-15 port	Configuration 1
RG-58A/U 50ohm coaxial	Configuration 2

INTERRUPT SELECTION
IRQ	JP1	JP2	JP3	JP4	JP5
3	Closed	Open	Open	Open	Open
5	Open	Closed	Open	Open	Open
9	Open	Open	Closed	Open	Open
11	Open	Open	Open	Closed	Open
15	Open	Open	Open	Open	Closed

DMA CHANNEL SELECTION
Channel	CH7	CH5	CH1	CH3
DMA7	Closed	Open	Open	Open
DMA5	Open	Closed	Open	Open
DMA1	Open	Open	Closed	Open
DMA3	Open	Open	Open	Closed

DIAGNOSTIC LED(S)
LED1 (Red)	LED2 (Green)	Condition
Off	On	Network connection is good
On	On	Kernal and hardware failure
On	Off	Hardware failure
Off	Off	network connection is broken
Note: LED3 is lit only when UTP network connection is good

FACTORY CONFIGURED SETTINGS
Jumper	Setting
W15-18	Pins 2 & 3 closed