ETHERNIC/2000 TP Network Card Settings and Configuration
IMC NETWORK CORPORATION
ETHERNIC/2000 TP
NIC Type | Ethernet |
Transfer Rate | 10Mbps |
Data Bus | 8/16-bit ISA |
Topology | Linear Bus |
Wiring Type | Shielded/Unshielded twisted pair AUI transceiver via DB-15 port |
Boot ROM | Available |
INTERRUPT REQUEST | |||||||||
IRQ | JP1A | JP1B | JP1C | JP1D | JP1E | JP1F | JP1G | JP1H | |
2/9 | Open | Open | Open | Closed | Open | Open | Open | Open | |
| » | 3 | Closed | Open | Open | Open | Open | Open | Open | Open |
4 | Open | Closed | Open | Open | Open | Open | Open | Open | |
5 | Open | Open | Closed | Open | Open | Open | Open | Open | |
10 | Open | Open | Open | Open | Closed | Open | Open | Open | |
11 | Open | Open | Open | Open | Open | Closed | Open | Open | |
12 | Open | Open | Open | Open | Open | Open | Closed | Open | |
15 | Open | Open | Open | Open | Open | Open | Open | Closed | |
Note:If a Boot ROM is to be installed, see the I/O base address & Boot ROM address table for valid interrupt settings. | |||||||||
COMPATIBILITY MODE | |||
Setting | JP2A | JP2B | |
| » | Disabled | Closed | Open |
Enabled | Open | Closed | |
Note:On some systems the data bus timing is not truly IBM PC/AT compatible. If the card is not initializing enabling compatibility mode may allow the card to operate properly.
| |||
DATA BUS SIZE | ||
Setting | JP2C | |
| » | Autosense | Closed |
8-bit | Open | |
Note:In autosense mode the card automatically detects if it is in a 16-bit or 8-bit slot. On some Rev. 01 cards this jumper is incorrectly labeled TURBO. | ||
I/O BASE ADDRESS & BOOT ROM ADDRESS | |||||
I/O Address | Boot ROM Address | JP3A | JP3B | JP3C | |
200 | N/A | Open | Open | Open | |
220 | N/A | Closed | Open | Open | |
240 | N/A | Open | Closed | Open | |
260 | N/A | Closed | Closed | Open | |
| » | 300 | C8000h (IRQ3) | Open | Open | Closed |
320 | CC000h (IRQ5) | Closed | Open | Closed | |
| 340h | D0000h (IRQ4) | Open | Closed | Closed | |
360h | N/A | Closed | Closed | Closed | |
Note:If a boot ROM is to be installed one of the I/O address configurations with a boot ROM address must be used and the indicated IRQ must be set.
| |||||
BOOT ROM | ||
Setting | JP3D | |
| » | Disabled | Closed |
Enabled | Open | |
CABLE TYPE | |||
Type | S1 | S3 | |
| » | Shielded/Unshielded twisted pair | Installed | Open |
AUI transceiver via DB-15 port | Open | Installed | |
Note:S1 and S3 are sockets for a transformer chip. To choose a cable type insert the transformer chip into the appropriate socket.
| |||
LINK INTEGRITY TEST | ||
Setting | JP4 | |
| » | Enabled | Pins 1 & 2 closed |
Disabled | Pins 2 & 3 closed | |
Note:The link integrity test is valid only when the cable type is shielded/unshielded twisted pair. | ||
DIAGNOSTIC LED(S) | |||
LED | Color | Status | Condition |
LED1 | Green | On | Twisted pair network connection is good |
LED1 | Green | Off | Twisted pair network connection is broken |
Note:LED1 indications are only valid when cable type is shielded/unshielded twisted pair. | |||
My Books
