CS-MAX-AUI ETHERNET-KARTE Network Card Settings and Configuration

NIC Type:	Ethernet
Transfer Rate:	10Mbps
Data Bus:	16-bit ISA
Topology:	Linear Bus Star
Wiring Type	AUI transceiver via DB-15 port RG58A/U 50ohm coaxial Shielded/unshielded twisted pair
Boot ROM	Available

INTERRUPT SELECT - J1
IRQ	A	B	C	D	E	F	G	H	I	J
3	Open	Open	Open	Open	Open	Open	Open	Open	Open	Closed
4	Open	Open	Open	Open	Open	Open	Open	Open	Closed	Open
5	Open	Open	Open	Open	Open	Open	Open	Closed	Open	Open
7	Open	Open	Open	Open	Open	Open	Closed	Open	Open	Open
9	Open	Open	Open	Open	Open	Closed	Open	Open	Open	Open
10	Open	Open	Open	Open	Closed	Open	Open	Open	Open	Open
11	Open	Open	Open	Closed	Open	Open	Open	Open	Open	Open
12	Open	Open	Closed	Open	Open	Open	Open	Open	Open	Open
14	Open	Closed	Open	Open	Open	Open	Open	Open	Open	Open
15	Closed	Open	Open	Open	Open	Open	Open	Open	Open	Open

DMA SELECT - J2 & J3
Channel		Jumper A	Jumper B	Jumper C	Jumper D	Jumper E	Jumper F	Jumper G
»	DMA5	Open	Open	Closed	Open	Open	Open	Open
	DMA0	Open	Open	Open	Open	Open	Open	Closed
	DMA1	Open	Open	Open	Open	Open	Closed	Open

DMA SELECT - J2 & J3
Channel	Jumper A	Jumper B	Jumper C	Jumper D	Jumper E	Jumper F	Jumper G
DMA2	Open	Open	Open	Open	Closed	Open	Open
DMA3	Open	Open	Open	Closed	Open	Open	Open
DMA6	Open	Closed	Open	Open	Open	Open	Open
DMA7	Closed	Open	Open	Open	Open	Open	Open
Note:The corresponding jumpers on both J2 and J3 are closed when designated. J2 is for DRQ and J3 is for DACK.

I/O & BOOT ROM ADDRESS - J4
I/O Address		Boot ROM Address	Jumper A	Jumper B	Jumper C
»	300h	C8000h	Closed	Closed	Closed
	300h	Disabled	Open	Closed	Closed
	320h	CC000h	Closed	Open	Closed
	320h	Disabled	Open	Open	Closed
	340h	D0000h	Closed	Closed	Open
	340h	Disabled	Open	Closed	Open
	360h	D4000h	Closed	Open	Open
	360h	Disabled	Open	Open	Open

WIRING TYPE SELECT
Setting	J5	J13/A	J13/B	J13/C	J13/D	J13/E	J13/F
AUI transceiver via DB-15	Closed	2 & 3	2 & 3	2 & 3	2 & 3	2 & 3	2 & 3
RG58A/U 50ohm coaxial	Open	2 & 3	2 & 3	2 & 3	2 & 3	2 & 3	2 & 3
Shielded/unshielded twisted pair	Closed	1 & 2	1 & 2	1 & 2	1 & 2	1 & 2	1 & 2
Note:The pins designated are in the closed position.

BNC TERMINATION - J11
Setting		Jumper A	Jumper B	Jumper C
»	Disabled	All pins open	Pins 2 & 3 closed	Pins 2 & 3 closed
	Enabled	Pins 1 & 2 closed	Pins 2 & 3 closed	Pins 2 & 3 closed

FACTORY CONFIGURED SETTINGS
Jumper	Setting
J15	Pins 2 & 3 closed

DIAGNOSTIC LEDS
LED	Color	Status	Condition
D1	Red	On	Data is being transmitted
D2	Green	On	Data is being received
D3	Red	On	Collision detected on network
D4	Green	On	Twisted pair network connection is good
D5	Red	On	Twisted pair network connection is broken