WILDCARD TECHNOLOGIES, INC.
SATISFAXTION MOBILE PDMCIA9023COMBO
Card Type | Modem (asynchronous), Ethernet |
Chipset | Intel 82595TX |
Maximum Onboard Memory | 160KB DRAM/128KB PROM |
Network Transfer Rate | 10Mbps |
Maximum Data Rate | 28.8Kbps |
Maximum Fax Rate | 14.4Kbps |
Data Bus | PCMCIA Type II |
Fax Class | Class I & II |
Data Modulation | Bell 103A/212A ITU-T V.21, V.22, V.23, V.22bis, V.32, V.32bis, V.34 Rockwell V.FC |
Fax Modulation | Unidentified |
Error Correction/Compression | MNP5, MNP10, V.42, V.42bis |
Topology | Star |
Wire Type | Unshielded twisted pair |
Boot ROM | Not available |
WILDCARD-TECHNOLOGIES-INC-Modem-asynchronous-Ether
SUPPORTED STANDARD COMMANDS |
Basic AT Commands |
+++, A/ |
A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z |
&C, &D, &F, &G, &P, &Q, &R, &S, &T, &V, &W, &Y, &Z |
Extended AT Commands |
\A, \B, \G, \J, \K, \L, \N |
%C, %L, %Q |
Special AT Commands |
-K, -Q, *H, )M, @M, :E, +MS |
S-Registers |
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25, |
S26, S27, S28, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S46, S48, S82, S86, S91, |
S92, S95, S201 |
Proprietary AT Command Set
AUTO-RETRAIN AND AUTO-FALLBACK/FALL-FORWARD | |
Type: | Configuration |
Format: | AT [cmds] %En [cmds] |
Description: | Controls auto-retrain mode and fallback/fall-forward |
Command | Function |
í %E0 | Auto-retrain disabled. |
%E1 | Auto-retrain enabled. |
%E2 | Auto-fallback/fall-forward enabled. |
%E3 | Auto-retrain and fast disconnect enabled. |
AUTOSYNC | ||
Format | AT [cmds] S19=n [cmds] | |
Default: | 0 | |
Range: | 0 - 63 | |
Unit: | Bit-mapped | |
Description: | Sets options for Hayes AutoSync functions. | |
Bit | Value | Function |
0 | 0 | Not used. |
1 | í 01 | BSC enabled. HDLC enabled. |
2 | í 01 | HDLC address detection disabled. HDLC address detection enabled. |
3 | í 01 | NRZI bit encoding enabled. NRZ bit encoding enabled. |
4 | í 01 | Mark idle enabled. Flag or sync idle enabled. |
AUTOSYNC HDLC ADDRESS | |
Type: | Register |
Format: | AT [cmds] S20=n [cmds] |
Default: | 0 |
Range: | 0-255 |
Unit: | Unidentified |
Description: | Sets the HDLC address or BSC character. |
COUNTRY CODE | |
Type: | Configuration |
Format: | AT [cmds] *NCnn [cmds] |
Description: | Changes the country code of the modem to nn. |
DIAL | |
Type: | Immediate |
Format: | AT [cmds] D<#> [cmds] |
Description: | Dials telephone number according to any modifiers included in the string |
Note: | Any combination of modifiers can be used to produce the desired dial functions in sequence. |
Command | Function |
DJ | MNP10 link will be negotiated at 1200bps for this call. |
DK | MNP10 power level adjustment enabled for this call. |
DL | Re-dial last number. |
DP | Pulse dialing enabled. |
DR | Answer mode enabled; originate mode disabled following handshake initiation. |
DS=n | Dial stored telephone number n. |
DT | Tone dialing enabled. |
DW | Dialing resumed following dial tone detection. |
D, | Dialing paused for amount of time specified in S8 register. |
D"WXY" | Optional method of denoting telephone numbers. Letters enclosed in quotes are interpreted as numbers according to the system found on a telephone keypad. |
D! | Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. |
D@ | Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. |
D$ | Wait for prompt tone detection function enabled. Modem waits for prompt tone for amount of time specified by the S7 command. |
D; | Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. |
D^ | Calling tone toggled from current setting for this call. |
PULSE DIAL CODE | ||
Type: | Configuration | |
Format: | AT [cmds] *Zn [cmds] | |
Description: | Sets the currently active pulse dialing code. | |
Command | Function | |
í *Z0 | Use dial code 0. | |
*Z1 | Use dial code 1. |
DISPLAY STORED NUMBERS | |
Type: | Immediate |
Format: | AT [cmds] \F [cmds] |
Description: | Displays all stored phone numbers. |
FLOW CONTROL | |
Type: | Configuration |
Format: | AT [cmds] &Kn [cmds] |
Description: | Enables flow control options. |
Command | Function |
&K0 | Flow control disabled. |
í &K3 | RTS/CTS flow control enabled. |
&K4 | XON/XOFF flow control enabled. |
&K5 | Transparent XON/XOFF flow control enabled. |
&K6 | RTS/CTS and XON/XOFF flow control enabled. |
REPORT INFORMATION | |
Type: | Immediate |
Format: | AT [cmds] In [cmds] |
Description: | Displays information requested |
Command | Function |
I0 | Reports modem model and speed |
I1 | Reports ROM checksum |
I2 | Tests and reports ROM checksum |
I3 | Reports firmware revision. |
I5 | Reports country code. |
REQUEST LIST OF FORBIDDEN NUMBERS | |
Type: | Immediate |
Format: | AT [cmds] *B [cmds] |
Description: | Requests the list of forbidden numbers from the modem. |
REQUEST LIST OF DELAYED NUMBERS | |
Type: | Immediate |
Format: | AT [cmds] *D [cmds] |
Description: | Requests the list of delayed numbers from the modem. |