LEOPARD 56K modem/telephone/ISDN Settings and Configuration

Card Type	Modem (asynchronous)
Chip Set	Rockwell
I/O Options	Line in, line out, microphone in, speaker out
Maximum Modem Rate	56Kbps
Maximum Fax Rate	14.4Kbps
Data Modulation Protocol	Bell 103/212A ITU-T V.34, V.FC, V.32bis, V.32, V.22bis, V.22, V.23, V.21
Fax Modulation Protocol	ITU-T V.17, V.21CH2, V.27ter, V.29, Unidentified
Error Correction/Compression	MNP5, V.42bis
Fax Class	Class I & II
Data Bus	16-bit ISA
Card Size	Half-length, half-height card

CONNECTIONS
Function	Label		Function		Label
Line out		CN1		Microphone		CN3
Line in		CN2		Speaker out		CN4

SUPPORTED COMMAND SET

Basic AT Commands

AT, A/

A, B, D, E, H, M, O, P, Q, T, V, W, X, Y, Z

&D, &M, &P, &Q, &R, &T, &W, &X, &Y, &Z

Extended AT Commands

\A, \B, \K, \N,

%C, %E, %L, %Q

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25, S26,

S27, S28, S29, S30, S38, S39, S40, S46, S48, S82, S91, S92, S95

Special Commands

-K, +MS

Note: See MHI Help File for full command documentation.

TRANSMIT CARRIER
Type:	Configuration
Format:	AT [cmds] Cn [cmds]
Description:	Controls the transmit carrier switching
Note: Disabling the transmit carrier puts the modem in receive-only mode
Command	Function
í C1	Return OK message

ECHOPLEX
Type:	Configuration
Format:	AT [cmds] Fn [cmds]
Description:	Selects whether commands sent while in data mode are echoed
Note: This command is only supported on older modems
Command	Function
F0	Auto detect mode
í F1	V.21 or Bell 103
F3	V.23 line modulation
F4	V.22 or Bell 212A 1200bps line speed
F5	V.22bis line modulation
F6	V.32bis or V.32 4800 line modulation
F7	V.32bis 7200 line modulation
F8	V.32bis or V.32 9600 line modulation
F9	V.32bis 12000 line modulation
F10	V.32bis 14400 line modulation

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested
Command	Function
I0	Reports modem model and speed
I1	Reports ROM checksum
I2	Report OK
I3	Report firmware revision, model, and interface type
I4	Report response programmed by OEM
I5	Report the country code parameter
I6	Report modem data pump model and code revision
I7	Report DAA code

SPEAKER VOLUME
Type:	Configuration
Format:	AT [cmds] Ln [cmds]
Description:	Controls speaker volume
Command	Function
L0	Low volume setting
L1	Low volume setting
L2	Medium volume setting
L3	Highest volume setting

AUTO-MODE DETECTION
Type:	Configuration
Format:	AT [cmds] Nn [cmds]
Description:	Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed.
Command	Function
N0	Auto-mode detection disabled
í N1	Auto-mode detection enabled

RLSD
Type:	Configuration
Format:	AT [cmds] &Cn [cmds]
Description:	Selects whether the RLSD option is enabled or disabled
Command	Function
í &C0	Force RLSD active regardless of the carrier state
&C1	Allow RLSD to follow the carrier state

FACTORY DEFAULT PROFILE
Type:	Configuration
Format:	AT [cmds] &F [cmds]
Description:	Sets values in active profile to values found in the default profile
Command	Function
í &F0	Restore factory configuration 0
&F1	Restore factory configuration 1

GUARD TONE
Type:	Configuration
Format:	AT [cmds] &Gn [cmds]
Description:	Commands the modem to transmit a guard tone in V.22/V.22bis
Note: Used primarily for international data transmission
Command	Function
í &G0	Guard tone disabled
&G1	Guard tone disabled
&G2	1800Hz guard tone enabled

JACK TYPE
Type:	Configuration
Format:	AT [cmds] &Jn [cmds]
Description:	Included for compatibility, performs no function.

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] &Kn [cmds]
Description:	Enables flow control options
Command	Function
&K0	Flow control disabled
í &K3	RTS/CTS flow control enabled
&K4	XON/XOFF flow control enabled
&K5	Transparent XON/XOFF flow control enabled
&K6	RTS/CTS and XON/XOFF flow control enabled

LINE TYPE
Type:	Configuration
Format:	AT [cmds] &Ln [cmds]
Description:	Selects line type
Command	Line Type
&L0	Switched line (PSTN/Dial-up)

DATA SET READY (DSR)
Type:	Configuration
Format:	AT [cmds] &Sn [cmds]
Description:	Selects DSR options
Command	Function
&S0	DSR forced high
í &S1	DSR high only while modem is handshaking or connected

CONFIGURATION PROFILES
Type:	Immediate
Format:	AT [cmds] &V [cmds]
Description:	Displays active and stored configuration profiles
Command	Function
&V1	Displays the connection statistics

CONNECT MESSAGE
Type:	Configuration
Format:	AT [cmds] \Vn [cmds]
Description:	Selects extended result codes
Command	Function
\V0	Connect messages are controlled by the command settings X, W, and S95
\V1	Connect messages are displayed in the single line format

AUTO-RELIABLE FALLBACK CHARACTER
Type:	Configuration
Format:	AT [cmds] %An [cmds]
Default:	19
Range:	0-127
Unit:	ASCII
Description:	Sets the character used as the auto-reliable fallback character
Command	Function
%A0	Disable

PLUG AND PLAY SERIAL NUMBER
Type:	Immediate
Format:	AT [cmds] %7 [cmds]
Description:	Displays the Plug and Play serial number

PLUG AND PLAY VENDOR ID
Type:	Immediate
Format:	AT [cmds] %8 [cmds]
Description:	Displays the Plug and Play vendor ID and product number

MNP10 - FALLBACK
Type:	Configuration
Format:	AT [cmds] -SECn [cmds]
Description:	Allows MNP10 to fall back to speeds slower than 4800bps
Command	Function
-SEC0	MNP 10-EC disabled
-SEC1	MNP 10-EC enabled and set transmit level <tx level> 0 to 30

DISTINCTIVE RING
Type:	Configuration
Format:	AT [cmds] -SDR=n [cmds]
Description:	Controls the distinctive ring type
Command	Function
-SDR=0	Disable distinctive ring
-SDR=1	Ring type 1
-SDR=2	Ring type 2
-SDR=3	Ring type 1 and 2
-SDR=4	Ring type 3
-SDR=5	Ring type 1 and 3
-SDR=6	Ring type 2 and 3
-SDR=7	Ring type 1, 2, and 3

RPI MODE
Type:	Configuration
Format:	AT [cmds] +H [cmds]
Description:	Sets the flash memory download speed
Command	Function
+H0	RPI/Video Ready Mode disabled
+H1	RPI enabled and DTE speed set to 19200kps
+H2	RPI enabled and DTE speed set to 38400kps
+H3	RPI enabled and DTE speed set to 57600kps
+H11	RPI+ mode enabled
+H16	Video Ready Mode enabled

BLACKLISTED NUMBERS
Type:	Configuration
Format:	AT [cmds] *B [cmds]
Description:	Displays the list of permanently blacklisted numbers

DELAYED NUMBERS
Type:	Configuration
Format:	AT [cmds] *D [cmds]
Description:	Displays the list of delayed numbers

COUNTRY
Type:	Configuration
Format:	AT [cmds] *NCn [cmds]
Description:	Changes the country to one of eight listed in NVRAM

BIT-MAPPED REGISTER S19
Format	AT [cmds] S19=n [cmds]
Default:	0
Range:	Unidentified
Description:	AutoSync options

BIT-MAPPED REGISTER S20
Format	AT [cmds] S20=n [cmds]
Default:	0
Range:	0-255
Unit:	Bit-mapped
Description:	AutoSync HDLC address or BSC Sync character

BIT-MAPPED REGISTER S31
Format:		AT [cmds] S31=n [cmds]
Default:		Unidentified
Range:		0-10
Description:		Select automode and extended result code format.
Bit	Value		Function
0	0		Not used
1	0 1		Auto-mode detection disabled In originate mode, handshake begins at line speed designated by the S37 register. Modem can shift to a slower speed if necessary. In answer mode, handshake attempted with the following protocols in order - V.FC, V.32bis, V.32, V.22bis, V.22 or Bell 212, V.21, and Bell 103
2-3	0 1		Auto line speed detection (Nn) disabled Auto line speed detection (Nn) enabled
4-5	0 1 2		Caller ID disabled Short Caller ID enabled Long Caller ID enabled
6-7	11b		Reserved

DCE LINE SPEED
Type:	Register
Format	AT [cmds] S37=n [cmds]
Description:	Sets the maximum allowable data exchange rate attempted during handshake process.
Command	Function
S37=0	Attempt automode connection. If N0 is active, connection is attempted at the most recently sensed DTE speed. If N1 is active, connection is attempted at the highest possible speed.
S37=1-3	Attempt to connect at 300bps
S37=4	Reserved
S37=5	Attempt to connect at 1200bps
S37=6	Attempt to connect at 2400bps
S37=7	Attempt to connect at V.23
S37=8	Attempt to connect at 4800bps
S37=9	Attempt to connect at 9600bps
S37=10	Attempt to connect at 12000bps
S37=11	Attempt to connect at 14400bps
S37=12	Attempt to connect at 7200bps

BIT-MAPPED REGISTER S41
Format		AT [cmds] S41=n [cmds]
Default:		Unidentified
Range:		0-31
Unit:		Bit-mapped
Description:		Selects compression, auto-retrain, flow control, and MNP mode.
Bit	Value	Function
0-1	0 1 2 3	Disabled MNP5 V.42bis MNP5 and V.42bis
2,6	0,0 0,1 1,0	Retrain and fallback/fall forward disabled Retrain enabled Fallback/fall forward enabled
3		Reserved
4-5		Reserved
7		Reserved

BIT-MAPPED REGISTER S86
Format	AT [cmds] S86=n [cmds]
Default:	Unidentified
Range:	0, 4, 5, 9, 12, 13, 14
Unit:	Bit-mapped
Description:	Records the first event that contributes to a NO CARRIER message.
Command	Function
S86=0	Normal disconnect, no error occurred
S86=4	Loss of carrier
S86=5	V.42 negotiation failed to detect an error-correction modem at the other end
S86=9	The modems could not find a common protocol
S86=12	Normal disconnect initiated by the remote modem
S86=13	Remote modem does not respond after 10 re-transmissions of the same message
S86=14	Protocol violation