MAXTECH CORPORATION
PCM336
Card Type | Modem (asynchronous) |
Chipset | Unidentified |
Maximum Data Rate | 33.6Kbps |
Maximum Fax Rate | 14.4Kbps |
Data Modulation | Bell 103A, 212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Rockwell V.FC |
Fax Modulation | ITU-T V.17, V.27ter, V.29 |
Error Correction/Compression | MNP5, MNP10EC, V.42, V.42bis |
Fax Class | Class I & II |
Data Bus | PCMCIA Type II |
MAXTECH-CORPORATION-Modem-asynchronous-PCM336
SUPPORTED STANDARD COMMANDS |
Basic AT Commands |
+++, A/ |
A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z |
&C, &D, &F, &G, &K, &P, &S, &T, &V, &W, &Y, &Z |
Extended AT Commands |
\A, \B, \L, \N, \V |
%C, %E, %Q |
Special AT Commands |
#CID, :E, *H, -K, )M, @M, +MS, -Q |
S-Registers |
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S18, S24, S25, S26, S29, S30, S32, S33 |
S38, S46, S48, S82, S86, S91, S92, S95 |
Note: See MHI help file for complete information. |
UNIDENTIFIED COMMANDS | |
Command | Default |
\K | 5 |
S14 | Unidentified |
S16 | Unidentified |
S21 | Unidentified |
S22 | Unidentified |
S23 | Unidentified |
S27 | Unidentified |
S28 | Unidentified |
S31 | Unidentified |
S36 | 7 |
S37 | 0 |
S39 | 3 |
S40 | 104 |
S41 | 195 |
Proprietary AT Command Set
DIAL | |
Type: | Immediate |
Format: | AT [cmds] D <#>;[cmds] |
Description: | Dials the telephone number indicated according to any modifiers included in the string. |
Command | Function |
DP | Pulse dialing enabled. |
DS=n | Dial stored telephone number n. |
DT | Tone dialing enabled. |
DW | Dialing resumed following dial tone detection. |
D, | Dialing paused for amount of time specified in S8 register. |
D! | Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. |
D@ | Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. |
D^ | Calling tone disabled for this call. |
D& | Wait for prompt tone detection function enabled. Waits for prompt tone for amount of time specified by the S7 command. |
D; | Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. |
DISPLAY INFORMATION | |
Type: | Immediate |
Format: | AT [cmds] In [cmds] |
Description: | Displays information requested about the modem. |
Command | Function |
I0 | Displays product identification code. |
I1 | Performs ROM testing. |
I2 | Performs RAM testing. |
I3 | Displays firmware revision. |
I4 | Displays internal factory ID. |
I6 | Displays data pump version. |
I7 | Displays DAA code. |
MNP10EC MODE | ||
Type: | Configuration | |
Format: | AT [cmds] -SEC=n [cmds] | |
Description: | Selects whether the modem will attempt to use MNP10EC mode during the handshaking sequence. | |
Command | Function | |
-SEC=0 | MNP10EC handshaking disabled unless a V.34 connection is attempted via a cellular line. | |
í -SEC=1 | MNP10EC handshaking enabled. |