BANKSIA TECHNOLOGY PTY., LTD.
MY MODEM
Card Type | Fax, Modem (asynchronous) |
Chip Set | Unidentified |
Maximum Data Rate | 14.4Kbps |
Maximum Fax Rate | 14.4Kbps |
Data Bus | External |
Fax Class | Class I & II |
Data Modulation Protocol | Bell 103/212A ITU-T V.21, V.22, V.22bis, V.32, V.32bis |
Fax Modulation Protocol | ITU-T V.17, V.27ter, V.29 |
Error Correction/Compression | MNP5, MNP10, V.42, V.42bis |
CONNECTIONS | ||||||
Function | Label | Function | Label | |||
Line out | CN1 | DC power | CN4 | |||
Line in | CN2 | Power switch | SW1 | |||
RS-232/422 | CN3 |
DIAGNOSTIC LED(S) | |||
LED | Color | Status | Condition |
PWR | Red | On | Power is on |
PWR | Red | Off | Power is off |
OH | Red | On | Modem is off-hook |
OH | Red | Off | Modem is on-hook |
DTR | Red | On | DTR signal is high |
DTR | Red | Off | DTR signal is low |
DCD | Red | On | Carrier signal detected |
DCD | Red | Off | Carrier signal not detected |
CTS | Red | On | Modem ready to receive data |
CTS | Red | Off | Modem not ready to receive data |
RTS | Red | On | Computer ready to receive data |
RTS | Red | Off | Computer not ready to receive data |
RXD | Red | On | Modem is receiving data |
RXD | Red | Off | Modem is not receiving data |
TXD | Red | On | Modem is transmitting data |
TXD | Red | Off | Modem is not transmitting data |
AA | Red | On | Auto-answer enabled |
AA | Red | Off | Auto-answer disabled |
TST | Red | On | Modem in test mode |
TST | Red | Off | Modem not in test mode |
SUPPORTED COMMAND SET |
Basic AT Commands |
AT, ‘+++’, ‘Comma’, A/ |
A, B, E, H, I, L, M, N, O, P, Q, S, T, V, W, X, Y, Z |
&C, &D, &F, &K, &L, &P, &S, &T, &V, &W, &Y, &Z |
Extended AT Commands |
\A, \B, \G, \L, %C, %L, %Q |
S Registers |
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S24, S25, S26 |
S29, S30, S31, S32, S33, S36, S37, S38, S39, S46, S48, S82, S86, S91, S92, S95 |
Special Commands |
*H, -K, -Q, )M, @M, :E, +MS |
Note: See MHI Help file for full command documentation. |
Proprietary AT Command Set
MODULATION SELECTION | ||
Type: | Configuration | |
Format: | AT [cmds] Fn [cmds] | |
Description: | Controls line modulation unless automode is selected | |
Command | Function | |
F0 | Automode enabled | |
F1 | Force V.21 or Bell103 (according to ATB command) at 300bps | |
F2 | ‘OK’ returned | |
F3 | Force V.23 75TX/1200RX originate or 1200TX/75RX answer FSK | |
F4 | Force V.22 or Bell212A (according to ATB command) at 1200bps | |
F5 | Force V.22bis or Bell2400 (according to ATB command) | |
F6 | Force V.32 at 4800bps | |
F7 | Force V.32 at 7200bps | |
F8 | Force V.32 at 9600bps | |
F9 | Force V.32bis at 12000bps | |
F10 | Force V.32bis at 14400bps |
For remaining proprietary command summary, See BANKSIA TECHNOLOGY PTY., LTD., MAC MODEM 288.