MAX 2000 T1/PRI modem/telephone/ISDN Settings and Configuration

Card Type	T1, Ethernet
Chip Set	Unidentified
I/O Options	AC power connector, 15-pin AUI port, 9-pin serial port, T1 network interface via RJ-48 connector (2), alarm relay terminal block, RJ-45 UTP interface, data port via 44-pin connector,
Wiring Type	RJ-48 T1 RJ-45 Unshielded Twisted Pair
T1 Transfer Rate	1.544Mbps
T1 Protocol	AMI, B8ZS
Frame type	D4, ESF
Data Bus	External

CONNECTIONS
Function	Label	Function	Label
AC power connector	CN1	RJ-45 UTP connector	CN5
Serial port	CN2	RJ-48 T1 interface	CN6
44-pin DTE port	CN3	RJ-48 T1 interface	CN7
15-pin AUI interface	CN4	Alarm relay terminal block	CN8

DIAGNOSTIC LED(S)
LED	Color	Status	Condition
PWR	Unidentified	On	Power is on
PWR	Unidentified	Off	Power is off
ACT	Unidentified	On	Ethernet interface active
ACT	Unidentified	Off	Ethernet interface inactive
YA1	Unidentified	On	Yellow alarm condition detected on network line 1
YA1	Unidentified	Off	Yellow alarm condition not detected on network line 1
FLT	Unidentified	On	Self test in progress
FLT	Unidentified	Blinking	Device is not functional due to hardware fault or error
FLT	Unidentified	Off	Device is functional
COLL	Unidentified	On	Collision detected on Ethernet
COLL	Unidentified	Off	Collision not detected on Ethernet
LA1	Unidentified	On	Link is active on line 1
LA1	Unidentified	Blinking	Device unable to establish line 1 communications, possible configuration error
LA1	Unidentified	Off	Link is inactive
AUI	Unidentified	On	AUI interface is good
AUI	Unidentified	Off	AUI interface is broken
RA1	Unidentified	On	Improper receive signal or no signal detected on network line 1
RA1	Unidentified	Off	Improper receive signal or no signal detected on network line 1
COAX	Unidentified	On	10Base - 2 interface enabled
COAX	Unidentified	Off	10Base - 2 interface disabled
RA2	Unidentified	On	Improper receive signal or no signal detected on network line 2
RA2	Unidentified	Off	Improper receive signal or no signal detected on network line 2
UTP	Unidentified	On	10BaseT interface enabled
UTP	Unidentified	Off	10BaseT interface disabled
YA2	Unidentified	On	Yellow alarm condition detected on network line 2
YA2	Unidentified	Off	Yellow alarm condition not detected on network line 2
LA2	Unidentified	On	Link is active on line 2
LA2	Unidentified	Blinking	Device unable to establish line 2 communications, possible configuration error
LA2	Unidentified	Off	Link is inactive

MULTIBAND INVERSE MULTIPLEXING CARD

CONNECTIONS
Function	Label	Function	Label
Serial host port (44-pin connector)	CN9	Serial host port (44-pin connector)	CN11
Unidentified	CN10
Note: Serial host ports may be configured for RS-449, V.35, or X.21 interface. Also available with 6 serial host ports.

CONNECTIONS
Function	Label	Function	Label
9-pin serial port	CN12	9-pin serial port	CN13

MISCELLANEOUS TECHNICAL NOTES

MAX 200 T1/PRI can accommodate two expansion modules. Available modules are the two options shown above, as well as the Digital Modem and V.110 cards.