APACHE A56SP-R modem/telephone/ISDN Settings and Configuration

APACHE MICRO PERIPHERALS, INC.

APACHE A56SP-R

Card Type
Modem (asynchronous)
Chip Set
Unidentified
I/O Options
Speaker out, microphone, line in, line out
Maximum Modem Rate
56Kbps
Maximum Fax Rate
14.4Kbps
Data Modulation Protocol
Bell 103/212A
ITU-T V.21, V.22bis, V.23, V.32, V.32bis, V.34, V.34+, V.FC, K56flex, V.90
Fax Modulation Protocol
ITU-T V.17, V.21 CH2, V.27ter, V.29
Error Correction/Compression
MNP5, V.42, V.42bis
Fax Class
Class I
Data Bus
16-bit ISA
Card Size
Half-length, full-height card

CONNECTIONS
Function
Label
Function
Label
Line out
CN1
Microphone
CN3
Line in
CN2
Speaker out
CN4

SERIAL PORT ADDRESS
Setting
SW1/5
SW1/6
COM1 (3F8h)
On
On
COM2 (2F8h)
Off
On
COM3 (3E8h)
On
Off
COM4 (2E8h)
Off
Off

INTERRUPT
Setting
SW1/1
SW1/2
SW1/3
SW1/4
SW1/7
JP1
IRQ 2
Off
Off
Off
Off
On
Open
IRQ 3
Off
Off
Off
On
Off
Open
IRQ 4
Off
Off
On
Off
Off
Open
IRQ 5
Off
On
Off
Off
Off
Open
IRQ 7
On
Off
Off
Off
Off
Open
IRQ 10
Off
Off
Off
Off
Off
2 & 3
IRQ 11
Off
Off
Off
Off
Off
1 & 2
Note: Pins designated are in the closed position

SUPPORTED COMMAND SET
Basic AT Commands
AT, A/
A, B, D, E, H, M, O, P, Q, T, V, W, X, Y, Z
&C, &D, &M, &P, &Q, &R, &T, &W, &X, &Y, &Z
Extended AT Commands
\A, \B, \K, \N
%C, %E, %L, %Q
S Registers
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25,
S26, S27, S28, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S46, S48, S82, S86,
S91, S92, S95
Special Commands
-K, +MS
Note: See MHI Help File for full command documentation.

Proprietary AT Command Set

TRANSMIT CARRIER
Type:
Configuration
Format:
AT [cmds] Cn [cmds]
Description:
Controls the transmit carrier switching
Note: Disabling the transmit carrier puts the modem in receive-only mode
Command
Function
í C1
Return OK message

LINE MODULATION
Type:
Configuration
Format:
AT [cmds] Fn [cmds]
Description:
Selects the line modulation
Note: This command is only supported on older modems
Command
Function
F0
Auto-detect mode
í F1
V.21 or Bell 103
F3
V.23
F4
V.22 or Bell 212A @ 1200bps
F5
V.22bis
F6
V.32bis or V.32 @ 4800bps
F7
V.32bis @ 7200bps
F8
V.32bis or V.32 @ 9600bps
F9
V.32bis @ 12000bps
F10
V.32bis @ 14400bps

REPORT INFORMATION
Type:
Immediate
Format:
AT [cmds] In [cmds]
Description:
Displays information requested
Command
Function
I0
Reports product code
I1
Reports ROM checksum
I2
Reports OK
I3
Report firmware revision, model interface type
I4
Reports response programmed by an OEM
I5
Reports country code
I6
Reports modem data pump model and code revision
I7
Reports DAA code (W-class only)

SPEAKER VOLUME
Type:
Configuration
Format:
AT [cmds] Ln [cmds]
Description:
Controls speaker volume
Command
Function
L0
Low volume setting
L1
Low volume setting
í L2
Medium volume setting
L3
Highest volume setting

AUTO-MODE DETECTION
Type:
Configuration
Format:
AT [cmds] Nn [cmds]
Description:
Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed.
Command
Function
N0
Auto-mode detection disabled
N1
Auto-mode detection enabled

FACTORY DEFAULT PROFILE
Type:
Configuration
Format:
AT [cmds] &F [cmds]
Description:
Sets values in active profile to values found in the default profile
Command
Function
í &F0
Restore factory profile 0
&F1
Restore factory profile 1

GUARD TONE
Type:
Configuration
Format:
AT [cmds] &Gn [cmds]
Description:
Commands the modem to transmit a guard tone in V.22/V.22bis
Note: Used primarily for international data transmission
Command
Function
í &G0
Guard tone disabled
&G1
Guard tone disabled
&G2
1800Hz guard tone enabled

S-REGISTER RESPONSE
Type:
Configuration
Format:
AT [cmds] &Jn [cmds]
Description:
This command included for compatibility. It performs no function.

FLOW CONTROL
Type:
Configuration
Format:
AT [cmds] &Kn [cmds]
Description:
Enables flow control options
Command
Function
&K0
Flow control disabled
&K3
RTS/CTS flow control enabled
&K4
XON/XOFF flow control enabled
&K5
Transparent XON/XOFF flow control enabled
&K6
RTS/CTS and XON/XOFF flow control enabled

LINE TYPE
Type:
Configuration
Format:
AT [cmds] &Ln [cmds]
Description:
Selects line type
Command
Line Type
í &L0
Switched line (PSTN/Dial-up)

DATA SET READY (DSR)
Type:
Configuration
Format:
AT [cmds] &Sn [cmds]
Description:
Selects DSR options
Command
Function
&S0
DSR forced high
&S1
DSR high while modem is handshaking or connected

CONFIGURATION PROFILES
Type:
Immediate
Format:
AT [cmds] &V [cmds]
Description:
Displays active and stored configuration profiles
Command
Function
&V1
Display connection statistics

Extended AT Commands

EXTENDED RESULT CODES
Type:
Configuration
Format:
AT [cmds] \Vn [cmds]
Description:
Selects extended result codes
Command
Function
\V0
Connect messages are controlled by settings X, W, and S95
\V1
Connect messages are displayed in the single line format

PLUG AND PLAY SERIAL NUMBER
Type:
Immediate
Format:
AT [cmds] %7 [cmds]
Description:
Returns the plug & play serial number

PLUG AND PLAY VENDOR ID
Type:
Immediate
Format:
AT [cmds] %8 [cmds]
Description:
Returns the plug & play vendor ID and product number

RPI MODE SELECTION
Type:
Configuration
Format:
AT [cmds] +Hn [cmds]
Description:
Sets the RPI mode
Command
Function
+H0
RPI/video ready mode disabled
+H1
RPI enabled and set DTE speed to 19200bps
+H2
RPI enabled and set DTE speed to 38400bps
+H3
RPI enabled and set DTE speed to 57600bps
+H11
RPI+ mode enabled
+H16
Video ready mode enabled

DISTINCTIVE RING
Type:
Immediate
Format:
AT [cmds] -SDR=n [cmds]
Description:
Selects the distinctive ring settings
Command
Function
-SDR=0
Distinctive ring disabled
-SDR=1
Type 1 enabled
-SDR=2
Type 2 enabled
-SDR=3
Type 1 and 2 enabled
-SDR=4
Type 3 enabled
-SDR=5
Type 1 and 3 enabled
-SDR=6
Type 2 and 3 enabled
-SDR=7
Type 1, 2, and 3 enabled

MNP10-EC
Type:
Configuration
Format:
AT [cmds] -SECn [cmds]
Description:
Controls MNP10-EC
Command
Function
-SEC0
MNP10-EC disabled
-SEC1
MNP10-EC enabled ans set transmit (TX) level to 0 - 30

S(status) -REGISTERS

AUTOSYNC OPTIONS
Type:
Register
Format
AT [cmds] S19=n [cmds]
Default:
0
Range:
Unidentified
Description:
Sets the AutoSync option

AUTOSYNC HDLC ADDRESS
Type:
Register
Format
AT [cmds] S20=n [cmds]
Default:
0
Range:
0-255
Description:
Sets the AutoSync HDLC address of BSC Sync charactyer

Headaches Begone! A Systemic Approach To Healing Your Headaches

Don't Let Your Bike Seat Ruin Your Sex Life Book

APACHE A56SP-R modem/telephone/ISDN Settings and Configuration

Search

My Books

Discover

Card Type	Modem (asynchronous)
Chip Set	Unidentified
I/O Options	Speaker out, microphone, line in, line out
Maximum Modem Rate	56Kbps
Maximum Fax Rate	14.4Kbps
Data Modulation Protocol	Bell 103/212A ITU-T V.21, V.22bis, V.23, V.32, V.32bis, V.34, V.34+, V.FC, K56flex, V.90
Fax Modulation Protocol	ITU-T V.17, V.21 CH2, V.27ter, V.29
Error Correction/Compression	MNP5, V.42, V.42bis
Fax Class	Class I
Data Bus	16-bit ISA
Card Size	Half-length, full-height card

CONNECTIONS
Function	Label		Function		Label
Line out		CN1		Microphone		CN3
Line in		CN2		Speaker out		CN4

SERIAL PORT ADDRESS
Setting	SW1/5	SW1/6
COM1 (3F8h)	On	On
COM2 (2F8h)	Off	On
COM3 (3E8h)	On	Off
COM4 (2E8h)	Off	Off

INTERRUPT
Setting	SW1/1	SW1/2	SW1/3	SW1/4	SW1/7	JP1
IRQ 2	Off	Off	Off	Off	On	Open
IRQ 3	Off	Off	Off	On	Off	Open
IRQ 4	Off	Off	On	Off	Off	Open
IRQ 5	Off	On	Off	Off	Off	Open
IRQ 7	On	Off	Off	Off	Off	Open
IRQ 10	Off	Off	Off	Off	Off	2 & 3
IRQ 11	Off	Off	Off	Off	Off	1 & 2
Note: Pins designated are in the closed position

TRANSMIT CARRIER
Type:	Configuration
Format:	AT [cmds] Cn [cmds]
Description:	Controls the transmit carrier switching
Note: Disabling the transmit carrier puts the modem in receive-only mode
Command	Function
í C1	Return OK message

LINE MODULATION
Type:	Configuration
Format:	AT [cmds] Fn [cmds]
Description:	Selects the line modulation
Note: This command is only supported on older modems
Command	Function
F0	Auto-detect mode
í F1	V.21 or Bell 103
F3	V.23
F4	V.22 or Bell 212A @ 1200bps
F5	V.22bis
F6	V.32bis or V.32 @ 4800bps
F7	V.32bis @ 7200bps
F8	V.32bis or V.32 @ 9600bps
F9	V.32bis @ 12000bps
F10	V.32bis @ 14400bps

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested
Command	Function
I0	Reports product code
I1	Reports ROM checksum
I2	Reports OK
I3	Report firmware revision, model interface type
I4	Reports response programmed by an OEM
I5	Reports country code
I6	Reports modem data pump model and code revision
I7	Reports DAA code (W-class only)

SPEAKER VOLUME
Type:	Configuration
Format:	AT [cmds] Ln [cmds]
Description:	Controls speaker volume
Command	Function
L0	Low volume setting
L1	Low volume setting
í L2	Medium volume setting
L3	Highest volume setting

AUTO-MODE DETECTION
Type:	Configuration
Format:	AT [cmds] Nn [cmds]
Description:	Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed.
Command	Function
N0	Auto-mode detection disabled
N1	Auto-mode detection enabled

FACTORY DEFAULT PROFILE
Type:	Configuration
Format:	AT [cmds] &F [cmds]
Description:	Sets values in active profile to values found in the default profile
Command	Function
í &F0	Restore factory profile 0
&F1	Restore factory profile 1

GUARD TONE
Type:	Configuration
Format:	AT [cmds] &Gn [cmds]
Description:	Commands the modem to transmit a guard tone in V.22/V.22bis
Note: Used primarily for international data transmission
Command	Function
í &G0	Guard tone disabled
&G1	Guard tone disabled
&G2	1800Hz guard tone enabled

S-REGISTER RESPONSE
Type:	Configuration
Format:	AT [cmds] &Jn [cmds]
Description:	This command included for compatibility. It performs no function.

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] &Kn [cmds]
Description:	Enables flow control options
Command	Function
&K0	Flow control disabled
&K3	RTS/CTS flow control enabled
&K4	XON/XOFF flow control enabled
&K5	Transparent XON/XOFF flow control enabled
&K6	RTS/CTS and XON/XOFF flow control enabled

LINE TYPE
Type:	Configuration
Format:	AT [cmds] &Ln [cmds]
Description:	Selects line type
Command	Line Type
í &L0	Switched line (PSTN/Dial-up)

DATA SET READY (DSR)
Type:	Configuration
Format:	AT [cmds] &Sn [cmds]
Description:	Selects DSR options
Command	Function
&S0	DSR forced high
&S1	DSR high while modem is handshaking or connected

CONFIGURATION PROFILES
Type:	Immediate
Format:	AT [cmds] &V [cmds]
Description:	Displays active and stored configuration profiles
Command	Function
&V1	Display connection statistics

EXTENDED RESULT CODES
Type:	Configuration
Format:	AT [cmds] \Vn [cmds]
Description:	Selects extended result codes
Command	Function
\V0	Connect messages are controlled by settings X, W, and S95
\V1	Connect messages are displayed in the single line format

PLUG AND PLAY SERIAL NUMBER
Type:	Immediate
Format:	AT [cmds] %7 [cmds]
Description:	Returns the plug & play serial number

PLUG AND PLAY VENDOR ID
Type:	Immediate
Format:	AT [cmds] %8 [cmds]
Description:	Returns the plug & play vendor ID and product number

RPI MODE SELECTION
Type:	Configuration
Format:	AT [cmds] +Hn [cmds]
Description:	Sets the RPI mode
Command	Function
+H0	RPI/video ready mode disabled
+H1	RPI enabled and set DTE speed to 19200bps
+H2	RPI enabled and set DTE speed to 38400bps
+H3	RPI enabled and set DTE speed to 57600bps
+H11	RPI+ mode enabled
+H16	Video ready mode enabled

DISTINCTIVE RING
Type:	Immediate
Format:	AT [cmds] -SDR=n [cmds]
Description:	Selects the distinctive ring settings
Command	Function
-SDR=0	Distinctive ring disabled
-SDR=1	Type 1 enabled
-SDR=2	Type 2 enabled
-SDR=3	Type 1 and 2 enabled
-SDR=4	Type 3 enabled
-SDR=5	Type 1 and 3 enabled
-SDR=6	Type 2 and 3 enabled
-SDR=7	Type 1, 2, and 3 enabled

MNP10-EC
Type:	Configuration
Format:	AT [cmds] -SECn [cmds]
Description:	Controls MNP10-EC
Command	Function
-SEC0	MNP10-EC disabled
-SEC1	MNP10-EC enabled ans set transmit (TX) level to 0 - 30

AUTOSYNC OPTIONS
Type:	Register
Format	AT [cmds] S19=n [cmds]
Default:	0
Range:	Unidentified
Description:	Sets the AutoSync option

AUTOSYNC HDLC ADDRESS
Type:	Register
Format	AT [cmds] S20=n [cmds]
Default:	0
Range:	0-255
Description:	Sets the AutoSync HDLC address of BSC Sync charactyer