lotus

previous page: Hard Drive: SEAGATE: ST14207WD     CAYMAN 4295MB 3.5"/HH    SCSI3 D/WI
  
page up: Hard Drive Specs from SEAGATE
  
next page: Hard Drive: SEAGATE: ST1480A 426MB 3.5"/HH    IDE / AT

Hard Drive: SEAGATE: ST14207WV CAYMAN 4294MB 3.5"/SL SCSI2 WIDE




S T 1 4 2 0 7 W V           C A Y M A N    SEAGATE
NO MORE PRODUCED                                      Native|  Translation
                                                      ------+-----+-----+-----
Form                 3.5"/SLIMLINE         Cylinders    4016|     |     |
Capacity form/unform  4294/      MB        Heads          20|     |     |
Seek time   / track   8.5/ 2.0 ms          Sector/track     |     |     |
Controller           SCSI2 SI/WI/FAS/AV    Precompensation
Cache/Buffer           512 KB              Landing Zone
Data transfer rate    6.700 MB/S int       Bytes/Sector      512
                     20.000 MB/S ext
Recording method                                    operating  | non-operating
                                                  -------------+--------------
Supply voltage     5/12 V       Temperature *C         5 55    |    -40 60
Power: sleep              W     Humidity     %         5 95    |      5 95
       standby            W     Altitude    km    -0.061  3.048|        12.192
       idle          12.8 W     Shock        g         5       |     50
       seek          14.3 W     Rotation   RPM      7200
       read/write    13.2 W     Acoustic   dBA
       spin-up            W     ECC        Bit
                                MTBF         h    1000000
                                Warranty Month
Lift/Lock/Park     YES          Certificates

Layout

CONNER CFP-4207W QUICK REFERENCE GUIDE 12/94 REV. C

  +---------------------------------------------------------++---+
  |      +-J1                                          ++++ ||XX J2
  |      | |                                           |||| ||XX |68
  |      | |                                           |||| ||XX |Pin
  |      | |                                           |||| ||XX |
  |      +-+                                           |||| ||XX |
  |                                                    *+*+ ||XX |
  |                                                    E8++ ||XX |
  |                                                      ++ ||XX |
  |                                              (Fuse)F1xx ||XX1|
  |  J3                                                  ++ ||+-+|
  | +-+ SS                         ++++++++              || ||| |J5
  | | | LED                        ++++++++              || ||| ||
  | | |                          E1 ****** E7            || ||| ||
  | +-+                                                  || ||+-1|
  |                                                      *+ ||xx |
 ++                                                         ||XX J4
 ++LED                                                      ||XX Power
  +---------------------------------------------------------++--1+

Jumpers

CONNER CFP-4207W QUICK REFERENCE 12/1994, REV. C

Jumper Setting
==============

Setting the SCSI Bus Address
----------------------------
There are four jumpers available for configuration of the SCSI ID:
E1, E2, E3 and E4.

 Setting the SCSI ID
 -------------------
  +-------+----------+----------+----------+----------+
  |SCSI ID|    E1    |    E2    |   E3     |   E4     |
  +-------+----------+----------+----------+----------+
  |  0    |OUT/OPEN  |OUT/OPEN  |OUT/OPEN  |OUT/OPEN  |
  +-------+----------+----------+----------+----------+
  |  1    |IN /GROUND|OUT/OPEN  |OUT/OPEN  |OUT/OPEN  |
  +-------+----------+----------+----------+----------+
  |  2    |OUT/OPEN  |IN /GROUND|OUT/OPEN  |OUT/OPEN  |
  +-------+----------+----------+----------+----------+
  |  3    |IN /GROUND|IN /GROUND|OUT/OPEN  |OUT/OPEN  |
  +-------+----------+----------+----------+----------+
  |  4    |OUT/OPEN  |OUT/OPEN  |IN /GROUND|OUT/OPEN  |
  +-------+----------+----------+----------+----------+
  |  5    |IN /GROUND|OUT/OPEN  |IN /GROUND|OUT/OPEN  |
  +-------+----------+----------+----------+----------+
  |  6    |OUT/OPEN  |IN /GROUND|IN /GROUND|OUT/OPEN  |
  +-------+----------+----------+----------+----------+
  |  7    |IN /GROUND|IN /GROUND|IN /GROUND|OUT/OPEN  |
  +-------+----------+----------+----------+----------+
  |  8    |OUT/OPEN  |OUT/OPEN  |OUT/OPEN  |IN /GROUND|
  +-------+----------+----------+----------+----------+
  |  9    |IN /GROUND|OUT/OPEN  |OUT/OPEN  |IN /GROUND|
  +-------+----------+----------+----------+----------+
  | 10    |OUT/OPEN  |IN /GROUND|OUT/OPEN  |IN /GROUND|
  +-------+----------+----------+----------+----------+
  | 11    |IN /GROUND|IN /GROUND|OUT/OPEN  |IN /GROUND|
  +-------+----------+----------+----------+----------+
  | 12    |OUT/OPEN  |OUT/OPEN  |IN /GROUND|IN /GROUND|
  +-------+----------+----------+----------+----------+
  | 13    |IN /GROUND|OUT/OPEN  |IN /GROUND|IN /GROUND|
  +-------+----------+----------+----------+----------+
  | 14    |OUT/OPEN  |IN /GROUND|IN /GROUND|IN /GROUND|
  +-------+----------+----------+----------+----------+
  | 15    |IN /GROUND|IN /GROUND|IN /GROUND|IN /GROUND|
  +-------+----------+----------+----------+----------+
   Open means open circuit or high impedance. Ground means
   TTL logic low or logic ground.

 Disabling Spin-Up at Power On
 -----------------------------
 A jumper in the E5 location, disables spin up after power-on for
 applications where spin up sequencing is necessary. Disabling spin up
 on application of power can also be enabled by setting the DSPN bit
 in MODE SELECT page 00H (Operating Parameters). The Host must issue a
 Start UNIT command to cause the drive to spin up.
   +---------+------+---------------------+
   |   E5    | DSPN | Result              |
   +---------+------+---------------------+
   |   IN    |  0   | Spin Disabled       |
   +---------+------+---------------------+
   |   IN    |  1   | Spin Disabled       |
   +---------+------+---------------------+
   |   OUT   |  0   | Spin up on Power On |
   +---------+------+---------------------+
   |   OUT   |  1   | Spin Disabled       |
   +---------+------+---------------------+

Delaying Spin Up at Power On
----------------------------
A jumper in the E6 location, delays spin up on power-up by the value
of the drive's SCSI ID multiplied by 4 seconds (i.e. SCSI ID 4 will
delay 16 seconds). Delaying spin up on application of power can also
be enabled by setting the SDLY bit in MODE SELECT page 00H (Operating
Parameters.)

   +---------+------+---------------------+
   |   E6    | SDLY | Result              |
   +---------+------+---------------------+
   |   IN    |  0   | Spin Delayed        |
   +---------+------+---------------------+
   |   IN    |  1   | Spin Delayed        |
   +---------+------+---------------------+
   |   OUT   |  0   | Spin up on Power On |
   +---------+------+---------------------+
   |   OUT   |  1   | Spin Delayed        |
   +---------+------+---------------------+

Disabling the SCSI Bus Parity
-----------------------------
SCSI parity is always enabled in both directions, unless the E7
Parity disable jumper is installed. Installing the jumper will cause
the drive to ignore SCSI bus Parity In but it will continue to
generate SCSI bus parity out.

Disabling SCSI Bus Terminator Power (TERMPWR)
---------------------------------------------
Power to the on-board terminators is provided by the higher of the
voltage supplied at Pin #17, 18, 51 & 52, J2 or the voltage level at
the 5 Volt power input to the drive minus one diode drop. Termination
Power to external terminators can be supplied by the drive through
Pin #17, 18, 51 & 52, J2. The TERMPWR line can be disconnected from
the drive by removing Jumper E8.

 Jumper E8 | Result
 ----------+----------------------------------------------------
   IN      | TERMPWR (J2, Pin #17, 18, 51 & 52) connected to the
           | drive's internal termination power.
 ----------+----------------------------------------------------
   OUT     | TERMPWR (J2, Pin #17, 18, 51 & 52) open circuit.

Setting the Bus Termination
---------------------------
Remove the SCSI Terminators in all but the last drive in the chain.

General

SEAGATE SUPPORT SERVICES

Seagate Technology
------------------
Technical Support Services
If you need assistance installing your drive, consult your dealer.
Dealers are familiar with their unique system configurations and can
help you with system conflicts and other technical issues. If you
need additional assistance with your Seagate(r) drive or other
Seagate products, use one of the Seagate technical support services
listed below.

SeaFONE at 1-800-SEAGATE (1-800-732-4283)
Seagate's 800 number allows toll-free access to automated self-help
services, providing answers to commonly asked questions,
troubleshooting tips and specifications for disc drives and tape
drives. This service is available 24 hours daily and requires a
touch-tone phone. If you need to speak to a technical support
engineer, dial this number and listen to the options for technical
support. (International callers can also reach this automated
self-help service by dialing 408-456-4496).

Seagate Technology online services
Using a modem, you can obtain troubleshooting tips, free utility
programs, drive specifications and jumper settings for Seagate's
entire product line. You can also download software for installing
and analyzing your drive.

SeaNET
You can obtain technical information on Seagate drives, Seagate
software and much more over the Internet from Seagate's World Wide
Web home page (http://www.seagate.com) or Seagate's ftp server
(ftp://ftp.seagate.com).

You may also send E-mail with your questions to DiscSupport@
Seagate.com or TapeSupport@Seagate.com.

SeaBOARD
SeaBOARD is a computer bulletin board system (BBS) that contains
information about Seagate's disc and tape drive products and is
available 24 hours daily. Set your communications software to eight
data bits, no parity and one stop bit (8-N-1). SeaBOARD phone numbers
are listed in the following table.

BBS Location Modem number
United States Disc: 408-434-1080; Tape: 408-456-4415
England 44-1628-478011
France 33 1-48 25 35 95
Germany 49-89-140-9331
Singapore 65-292-6973
Thailand 662-531-8111
Australia 61-2-9756-2359
Taiwan 886-2-719-6075

Seagate CompuServe forum
Online technical support for Seagate products is available on
CompuServe. To access our technical support forum, type go seagate.
This forum provides information similar to that found on SeaBOARD.
In addition, you can type questions or browse through previous
questions and answers on the forum messages.

Seagate Technology FAX services
SeaFAX
You can use a touch-tone telephone to access Seagate's automated FAX
system to receive technical support information by return FAX. This
service is available 24 hours daily.
Location Telephone number
United States 1-800-SEAGATE or 408-456-4496
England 44-1628-894084
Australia 61-2-9756-5170

Seagate technical support FAX
You can FAX questions or comments to technical support specialists 24
hours daily. Responses are sent during business hours.
Location FAX number
United States 408-944-9120
England 44-1628-890660
France 33 1-46 04 42 50
Germany 49-89-1430-5100
Australia 61-2-9725-4052
Singapore 65-293-4722
Hong Kong 852-2368 7173
Taiwan 886-2-715-2923
Korea 82-2-556-7294/4251

Seagate technical support
You can talk to a technical support specialist during business hours
Monday through Friday for one-on-one technical help. Before calling,
note your system configuration and drive model number (STxxxx). There
are several technical support phone numbers available for various
Seagate products.

 Location          Telephone  number
 United States Please dial 1-800-SEAGATE for the specific product
               telephone number.
               (6:00 A.M. to 11:15 A.M., 12:30 P.M. to 5:00 P.M.,
               Pacific time, M-F)
 England       44-1628-894083 (10:00 A.M. to 1:00 P.M., 2:00 P.M. to
               5:00 P.M., M-F)
 France        33 1-41 86 10 86 (9:30 A.M. to 12:30 P.M., 2:00
               P.M. to 5:00 P.M., M-F)
 Germany       Disc: 49-89-140-9332; (9:30 A.M. to 12:30 P.M., 2:00
               P.M. to 4:00 P.M., M-F)
               Tape: 49-89-140-9333
 Australia     61-2-9725-3366 (9:00 A.M. to 5:00 P.M., M-F)
 Singapore     65-290-3998 (9:00 A.M. to 12:00 P.M., 2:00
               P.M. to 5:00 P.M., M-F)
 Hong Kong     852-2368 9918
 Taiwan        886-2-514-2237
 Korea         82-2-556-8241

SeaTDD 408-944-9121
Using a telecommunications device for the deaf (TDD), you can send
questions or comments 24 hours daily and exchange messages with a
technical support specialist between 6:00 A.M. to 11:15 A.M. and
12:30 P.M. to 5:00 P.M. (Pacific time) Monday through Friday.

Customer Service Centers
Seagate direct OEM, Distribution, System Integrator and Retail
customers should contact your Seagate Service Representative for
warranty information. Other customers contact your place of
purchase. Seagate offers comprehensive customer support for all
Seagate drives. Seagate customer service centers are the only
facilities authorized to service Seagate drives. These services are
available worldwide.

Location Telephone number FAX number
United States 1-800-468-3472; 405-949-6740
Other Americas
(Canada & Brazil) 405-949-6706; 405-949-6738
Mexico 525-546-6965; 525-546-4888
Europe, Middle
East & Africa 31-2065-43300; 31-2065-34320
Asia Pacific &
Australia 65-485-3595; 65-485-4980
Japan 81-3-5462-2904; 81-3-3462-2979

Seagate, Seagate Technology and the Seagate logo are registered
trademarks of Seagate Technology, Inc. SeaFAX, SeaFONE, SeaBOARD,
SeaTDD, SeaNET, Medalist and DiscWizard are either trademarks or
registered trademarks of Seagate Technology, Inc. or one of its
subsidiaries. All other trademarks or registered trademarks are the
property of their respective owners.













TOP
previous page: Hard Drive: SEAGATE: ST14207WD     CAYMAN 4295MB 3.5"/HH    SCSI3 D/WI
  
page up: Hard Drive Specs from SEAGATE
  
next page: Hard Drive: SEAGATE: ST1480A 426MB 3.5"/HH    IDE / AT