Hard Drive: MICROSCIENCE: 7100-21 121MB 3.5"/HH IDE / AT

7 1 0 0 - 2 1    MICROSCIENCE
NO MORE PRODUCED                                      Native|  Translation
                                                      ------+-----+-----+-----
Form                 3.5"/HH               Cylinders    1077|  960|     |
Capacity form/unform   121/      MB        Heads           5|    7|     |
Seek time   / track  18.0/     ms          Sector/track   44|   35|     |
Controller           IDE / AT              Precompensation
Cache/Buffer               KB              Landing Zone
Data transfer rate    1.250 MB/S int       Bytes/Sector      512
                            MB/S ext
Recording method     RLL 2/7                        operating  | non-operating
                                                  -------------+--------------
Supply voltage     5/12 V       Temperature *C                 |
Power: sleep              W     Humidity     %                 |
       standby            W     Altitude    km                 |
       idle               W     Shock        g                 |
       seek               W     Rotation   RPM      3600
       read/write         W     Acoustic   dBA
       spin-up            W     ECC        Bit
                                MTBF         h      36000
                                Warranty Month
Lift/Lock/Park     YES          Certificates                                  

Layout

MICROSC. 7070-20/7100-00/-20/-21/7200-00 PRODUCT DESCRIPTION

  +---------------------------------------------------------+
  |                                                 +----+J4|XX
  |                                                 1----8  |XX Power
  |                                                         |1
  |                                                         |
  |                                                         |1
  |                                                         |XX I
  |                                                         |XX N
  |                                                         |XX T
  |                                                         |XX E
  |                                                         |XX R
  |                                                         |XX F
  |                                                         |XX A
  |                                                         |XX C
  |                                                         |XX E
  |                                                         |XX
  +---------------------------------------------------------+

Jumpers

MICROSC. 7070-20/7100-00/20/21/7200-00 PRODUCT DESCRIPTION

Jumper Setting
==============

J4 Master/Slave Select
----------------------

Pins 1-2 OPEN Single drive only
Pins 7-8 OPEN

Pins 1-2 CLOSED Master drive in a two drive system
Pins 7-8 OPEN

Pins 1-2 OPEN Slave drive in a two drive system
Pins 7-8 CLOSED

The other pins are not used!

Install

MICROSC. 7XXX/8XXX SERIES JUMPER SETTINGS 280095-004, REV. A

Installation Procedure
----------------------

1. Installation precautions
---------------------------
Four (4) 6-32UNC screws, with 3/16" (4.78mm) maximum screw length,
are required for installation. Use caution when installing the
mounting screws to ensure no contact is made with drive's printed
circuit board.

2. In the CMOS (System BIOS) setup, select drive type as follows
----------------------------------------------------------------
Select a hard drive type that is equal to or less than the formatted
capacity of the drive.

NOTE
Drive parameters cannot exceed the specified capacity.

- Use user defined type or manually enter the drive parameters.

3. Disk partion options
-----------------------
Use DOS "FDISK" to create the partition table.
Utility software such as Disk Manager or Speedstor may be used.

4. High Level Format Options
----------------------------
If DOS "FDISK" is used to create the partitions, then use DOS
"FORMAT" to do the high level format.

If Disk Manager is used to create the partitions, then use Disk
Manager to do the high level format.

If Speedstor is used to create partitions, then use Speedstor to do
the high level format.

Always low-level formatted at the factory!