Hard Drive: MAXTOR: 7290S 290MB 3.5"/SL SCSI2 FAST
7 2 9 0 S MAXTOR
NO MORE PRODUCED Native| Translation
------+-----+-----+-----
Form 3.5"/SLIMLINE Cylinders 1751| | |
Capacity form/unform 290/ MB Heads 4| | |
Seek time / track 16.0/ 5.0 ms Sector/track | | |
Controller SCSI2 SI/FAST Precompensation
Cache/Buffer 64 KB ON-BOARD Landing Zone
Data transfer rate 2.800 MB/S int Bytes/Sector 512
10.000 MB/S ext SYNC
Recording method RLL 1/7 operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C 5 55 | -40 71
Power: sleep W Humidity % 5 95 | 5 95
standby W Altitude km -0.061 3.048|
idle W Shock g 10 | 70
seek 3.8 W Rotation RPM 3551
read/write 4.0 W Acoustic dBA
spin-up 11.8 W ECC Bit
MTBF h 300000
Warranty Month 24
Lift/Lock/Park YES Certificates
Layout
MAXTOR 7290S JUMPER SETTING
+---------------------------------------------------------+ | +--J309 |XX | +-+-+-+-+++ |XX | +++++++++-+ ++ |XX J1 | +--+ | | +---+ || |XX | J305 J306 J307 J308 || |XX Inter- | +-+ || |XX face | J304/+-+RP301|| |XX | J303/+-+ ++ |XX | J302/+-+ ++ |XX | J301/+-+ || |XX | || |XX | RP302|| |XX | || |XX | ++ |X1 | | | |XX Power | |XX J2 +---------------------------------------------------------+ 1
Jumpers
MAXTOR 7290S JUMPER SETTING
Jumper setting
==============
x = Jumper set at factory
J301 Terminator Power Selection
-------------------------------
Terminator power generation may occur internally from the disk drive
(when J301 is jumpered), or externally from the SCSI bus. Factory
default is J301 jumpered.
J302 Drive Power-Up Option
---------------------------
Pin 1-2 OPEN Wait for Start Command - The disk drive will not
spin-up until the initiator issues a START/STOP
UNIT command with the start bit equal to one.
CLOSED Start When Power Applied - The spin motor starts
when power is supplied.
J303 Parity Disable Option
----------------------------
The parity disable jumper, J303, enables (open, factory default) or
disables (jumperred) odd parity detection in the disk drive.
J304 Reserved
--------------
RESERVED!
J305 Reserved
--------------
RESERVED!
J306 Reserved
--------------
RESERVED!
J307/308/309 Addressing
------------------------
+---------------+------------+
| Jumper | Address |
+---------------+------------+
| J309 | SEL 0 (LSB)|
| J308 | SEL 1 |
| J307 | SEL 2 (MSB)|
+---------------+------------+
When jumpered, the corresponding bit is a 1.
The SCSI bus supports connection of up to seven devices, but
communication can occur only between two SCSI devices at a time. Each
device has an assigned ID bit that establishes device priority on the
SCSI bus. When two SCSI devices communicate, one acts as an initiator
and the other as a target. The initiator orginates an operation and
the target performs the operation specified by the initiator. An
initiator can address up to seven other logical units (LUNs) attached
to one target. The drive has only one logical unit attached. (LUN=0).
J307/308/309 SCSI ID --------------------- +--------+----------+-------+-------+-------+ |SCSI ID | Priority | J307 | J308 | J309 | +--------+----------+-------+-------+-------+ | 0 | Lowest |OPEN |OPEN |OPEN | | 1 | . |OPEN |OPEN |CLOSED | | 2 | . |OPEN |CLOSED |OPEN | | 3 | . |OPEN |CLOSED |CLOSED | | 4 | . |CLOSED |OPEN |OPEN | | 5 | . |CLOSED |OPEN |CLOSED | |x 6 | . |CLOSED |CLOSED |OPEN | | 7 | Highest |CLOSED |CLOSED |CLOSED | +--------+----------+-------+-------+-------+
Each 7000 Series SCSI drive is shipped from the factory with an
ID of 6. This ID designation assures sufficient jumpers are available
for any address except 7 (which is usually reserved for the host
system).
J2 DC Power and pin connector assignments
-------------------------------------------
+------------+ pin 1 +12 VDC
| 1 2 3 4 | pin 2 +12 V Ground Return
+------------+ pin 3 + 5 V Ground Return
pin 4 + 5 VDC
General
MAXTOR SCSI INSTALLATION
GENERIC INSTALLATION PROCEDURE FOR A SCSI DRIVE
-----------------------------------------------------------
1. Install a 50 pin ribbon connector making sure pin 1, which
can be identified by the striped edge of the cable, is closest
to the power connector on the drive.
2. Install a DC power cable to the back of the drive.
3. Verify the SCSI ID selection.
Note: SCSI ID usually needs to be set to 0 to be the boot drive.
The last physical device on the SCSI bus must be terminated.
Any other drive or SCSI device connected between the host and
the device at the end of the bus must not be terminated.
4. Apply power to the computer.
4a. When memory test is complete go into your system's Standard
C-MOS set-up.
(Note: There are various ways to get into C-MOS set-up,
please refer to system's manual for instuctions.)
4b. Set the drive type to "Not Installed". This intelligent drive
will identify itself to the SCSI host adapter.
5. Boot from a DOS diskette that has FDISK.EXE and FORMAT.COM on
it. At the A> prompt type in FDISK. At the menu options select
option 1 to create a DOS partition. Another menu will appear and
from those options choose 1 to create a Primary DOS partition.
Select yes to make 1 large partition and it will automatically
become active. Then escape from FDISK.
6. At the A> prompt type in FORMAT C:/S
This does a high-level format on the drive and transfers the
system files in order for the drive to be bootable.
(Note: Maxtor SCSI drives are low-level formatted at the factory)
7. The drive is now bootable. As a test remove the DOS diskette
from A and press reset to re-boot the computer, a C> should be
displayed, the drive is now ready for operation.
My Books
