Hard Drive: FUJITSU: MHD-2021AT HORNET 9 2160MB 2.5"/SSL ATA3 ULTRA

M H D - 2 0 2 1 A T     H O R N E T   9    FUJITSU
                                                      Native|  Translation
                                                      ------+-----+-----+-----
Form                 2.5"/SUPERSLIMLINE    Cylinders    7289|     |     |
Capacity form/unform  2160/      MB        Heads           3|     |     |
Seek time   / track  13.0/ 2.5 ms          Sector/track     |     |     |
Controller           IDE / ATA3 ULTRA      Precompensation
Cache/Buffer           512 KB              Landing Zone
Data transfer rate          MB/S int       Bytes/Sector      512
                     33.300 MB/S ext UDM33
Recording method     EPR4ML                         operating  | non-operating
                                                  -------------+--------------
Supply voltage     5 V          Temperature *C         5 55    |    -40 65
Power: sleep          0.1 W     Humidity     %         8 90    |      5 95
       standby        0.4 W     Altitude    km    -0.300  3.000| -0.300 12.000
       idle           0.9 W     Shock        g       100       |    500
       seek           2.4 W     Rotation   RPM      4000
       read/write         W     Acoustic   dBA        30
       spin-up            W     ECC        Bit   SMART
                                MTBF         h     300000
                                Warranty Month
Lift/Lock/Park     YES          Certificates                                  

Layout

FUJITSU MHD-2021/2032AT/MHC2040AT JUMPER SETTING

    +-------------------------------------------------------------+
    |                                                             |
    |                                                             |
    |    +-----------------------------------------------C-A-+    |
    |    | * * * * * * * * * * * * * * * * * * * * * 1   * * |    |
    |    | * * * * * * * * * * * *   * * * * * * * * *   * * |    |
    +----+----------------------------------------------SWITCH----+
                                                         D B

Jumpers

FUJITSU MHD-2021AT/2032AT/MHC2040AT JUMPER SETTING

Jumper Setting
==============

    +-------------------------------------------------------------+
    |                                                             |
    |                                                             |
    |    +---------------------------------------------------+    |
    |    | * * * * * * * * * * * * * * * * * * * * * 1   * * |    |
    |    | * * * * * * * * * * * *   * * * * * * * * *   * * |    |
    +----+----------------------------------------------SWITCH----+

 Factory Default
 ---------------
 --------C-A-+
    *    * * |  OPEN
  * *    * * |
   ------D-B-+

 MASTER-device
    *    * * |
  * *    * * |
   ----------+
                Master drive (device #0) or slave (device #1) is
 SLAVE-device+  selected.
    *    * * |
  * *    xxx |  Note:
   ----------+  Pins A and C should be open.

 -CSEL-------+
    *    xxx |CSEL signal is enabled.
  * *    * * |
   ----------+
 NOTE
 The CSEL setting is not depended on setting between pins B and D.

By connecting the CSEL of the master device to the CSEL Line
(conductor) of the cable and connecting it to ground further, the
CSEL is set to low level.

The device is identified as a master device. At this time, the CSEL
of the slave device does not have a conductor. Thus, since the
slave device is not connected to the CSEL conductor, the CSEL is set
to high level. The device is identified as a slave device.

Install

-ANY DIREC.

Notes on installation
=====================

Installation direction
----------------------

     horizontally                           vertically
   +-----------------+             +--+                       +--+
   |                 |             |  +-----+           +-----+  |
   |                 |             |  |     |           |     |  |
 +-+-----------------+-+           |  |     |           |     |  |
 +---------------------+           |  |     |           |     |  |
                                   |  |     |           |     |  |
                                   |  |     |           |     |  |
 +---------------------+           |  +-----+           +-----+  |
 +-+-----------------+-+           +--+                       +--+
   |                 |
   |                 |
   +-----------------+

The drive will operate in all axis (6 directions).