Hard Drive: FUJITSU: M2723TAM 1224MB 2.5"/SSL ATA3

M 2 7 2 3 T A M    FUJITSU
                                                      Native|  Translation
                                                      ------+-----+-----+-----
Form                 2.5"/SUPERSLIMLINE    Cylinders    5157|     |     |
Capacity form/unform  1224/      MB        Heads           3|     |     |
Seek time   / track  12.0/ 3.0 ms          Sector/track     |     |     |
Controller           IDE / ATA3            Precompensation
Cache/Buffer           128 KB              Landing Zone
Data transfer rate    5.000 MB/S int       Bytes/Sector      512
                     16.700 MB/S ext PIO1
Recording method     PR4ML                          operating  | non-operating
                                                  -------------+--------------
Supply voltage     5 V          Temperature *C         5 55    |    -40 65
Power: sleep          0.3 W     Humidity     %         8 90    |      5 95
       standby        0.4 W     Altitude    km    -0.300  3.000| -0.300 12.000
       idle           1.0 W     Shock        g       100       |    300
       seek               W     Rotation   RPM      4000
       read/write         W     Acoustic   dBA        30
       spin-up        2.2 W     ECC        Bit   SMART
                                MTBF         h     300000
                                Warranty Month
Lift/Lock/Park     YES          Certificates                                  

Layout

FUJITSU M2723T JUMPER SETTING

  +--------------------------------------------------------+
  |                                                        |XX
  |                                                        |XXI
  |                                                        |XXN
  |                                                        |XXT
  |                                                        |XXE
  |                                                        |XXR
  |                                                        |XXF
  |                                                        |XXA
  |                                                        |XXC
  |                                                        |XXE
  |                                                        |XX
  |                                                        |XX
  |                                                        1XX
  |                                                        |xxJumper
  +--------------------------------------------------------+

Jumpers

FUJITSU M2723T JUMPER SETTING

Jumper Setting
==============

  +CNH1--1-----Interface---------  MASTER DEVICE
  |* *   * * * * * * * *
  |* *   * * * * * *
  +------------------

  +CNH1--1-----Interface---------  SLAVE
  |* *   * * * * * * * *
  |xxx   * * * * * *
  +B-D---2-----------

  +A-C---1-----Interface---------  CABLE SELECT
  |xxx   * * * * * * * *
  |* *   * * * * * *               CSEL signal is enabled
  +------------------

The CSEL setting is not depended on setting between pins B and D.

By connecting the CSEL of the master device to the CSEL Line
(conductor) of the cable and connecting it to ground further, the
CSEL is set to low level. The device is identified as a master
device. At this time, the CSEL of the slave device does not have a
conductor. Thus, since the slave device is not connected to the CSEL
conductor, the CSEL is set to high level. The device is identified as
a slave device.

Install

-ANY DIREC.

Notes on installation
=====================

Installation direction
----------------------

     horizontally                           vertically
   +-----------------+             +--+                       +--+
   |                 |             |  +-----+           +-----+  |
   |                 |             |  |     |           |     |  |
 +-+-----------------+-+           |  |     |           |     |  |
 +---------------------+           |  |     |           |     |  |
                                   |  |     |           |     |  |
                                   |  |     |           |     |  |
 +---------------------+           |  +-----+           +-----+  |
 +-+-----------------+-+           +--+                       +--+
   |                 |
   |                 |
   +-----------------+

The drive will operate in all axis (6 directions).