lotus

previous page: Hard Drive: FUJITSU: M1603SAU > 11/1995 544MB 3.5"/SL    SCSI2 FAST
  
page up: Hard Drive Specs from FUJITSU
  
next page: Hard Drive: FUJITSU: M1606SAU < 11/1995 1091MB 3.5"/SL    SCSI2 FAST

Hard Drive: FUJITSU: M1603TAU PICOBIRD 7 544MB 3.5"/SL ATA2 FAST




M 1 6 0 3 T A U     P I C O B I R D   7    FUJITSU
NO MORE PRODUCED                                      Native|  Translation
                                                      ------+-----+-----+-----
Form                 3.5"/SLIMLINE         Cylinders    3456| 1055|     |
Capacity form/unform   544/      MB        Heads           3|   16|     |
Seek time   / track  10.0/ 3.0 ms          Sector/track     |   63|     |
Controller           IDE / ATA2 FAST/ENHA  Precompensation
Cache/Buffer           256 KB              Landing Zone
Data transfer rate    5.500 MB/S int       Bytes/Sector      512
                     16.700 MB/S ext PIO4
Recording method     RLL 1/7                        operating  | non-operating
                                                  -------------+--------------
Supply voltage     5/12 V       Temperature *C         5 55    |    -40 60
Power: sleep              W     Humidity     %         8 80    |      5 95
       standby            W     Altitude    km    -0.300  3.000| -0.300 12.000
       idle               W     Shock        g         5       |     50
       seek               W     Rotation   RPM      5400
       read/write         W     Acoustic   dBA        38
       spin-up            W     ECC        Bit
                                MTBF         h     300000
                                Warranty Month        24
Lift/Lock/Park     YES          Certificates

Layout

FUJITSU M1603TA/1606TA JUMPER SETTING A1CA 01310-0012

  +---------------------------------------------------------+
  |                                                         |
  |                                                         |XX
  |                                                         |XX
  |                                                         |XX
  |                                                  CNH1   |XX
  |                                               9++++++   |XX
  |                                                ++++++2  |XX
  |                                                         |XX
  |                                                         |XX
  |                                                         |XX
  |                                                         |XX
  |                                                         |XX
  |                                                         |XX
  |                                                         |XX
  |                                                         |XX +5V
  |                                                         |XX RETURN
  |                                                         |XX +12V
  +---------------------------------------------------------+

Jumpers

FUJITSU M1603TA/M1606TA JUMPER SETTING A1CA 01310-0011

Jumper Setting
==============

CNH1 Jumper Setting
-------------------

  +------+--------------------+-------+--------+-------------------+
  | Pin  | Function           | OPEN  | CLOSED |  Remarks          |
  +------+--------------------+-------+--------+-------------------+
  | 1-2  | Drive type select  | Slave | Master*|     -             |
  +------+--------------------+-------+--------+-------------------+
  | 3-4  | RESERVED           |       |        |  NOT USED         |
  +------+--------------------+-------+--------+-------------------+
  | 5-6  | Auto Idle control  | Enable|Disable*|     -             |
  +------+--------------------+-------+--------+-------------------+
  | 7-8  | CSEL connected to  | No*   | Yes    |  Supported needed |
  |      | interface          |       |        |  from host (NOTE1)|
  +------+--------------------+-------+--------+-------------------+
  | 9-10 | RESERVED           |       |        |  NOT USED         |
  +------+--------------------+-------+--------+-------------------+

 NOTE1
 CSEL: Cable select mode gives an alternative method by which the
       drive may be set to MASTER or SLAVE. A special cable is
       needed to implement this feature and should only be used if
       supported by BOTH drives. CSEL mode should be used in
       conjunction with SLAVE and without ACMODE.

* = DEFAULT

Install

FUJITSU M1603TA/M1606TA JUMPER SETTING A1CA 01310-0011

Notes on installation
=====================

Drive mounting
--------------

     horizontally             vertically
   +-----------------+   +--+             +--+ +------------------+
   |                 |   |  +-----+ +-----+  | |                  | x
   |                 |   |  |     | |     |  | x+----------------+x
 +-+-----------------+-+ |  |     | |     |  | ||x              x||
 +---------------------+ |  |     | |     |  | ||  x          x  ||
                         |  |     | |     |  | ||    x      x    ||
      x           x      |  |     | |     |  | ||      x  x      ||
 +------x------x-------+ |  +-----+ +-----+  | ||       xx       ||
 +-+------x--x-------+-+ +--+             +--+ ||     x    x     ||
   |       xx        |                         ||   x        x   ||
   |     x    x      |                         || x            x ||
   +---x--------x----+                         |x                x|
     x            x                           x++----------------++x
      UNACCEPTABLE!                                UNACCEPTABLE!

Orientation
-----------
The drive may be installed in one of three orientations; PCA down
or on either edge. Inclination from vertical or horizontal should
not exceed 5*.

Mounting screw fixing
---------------------
When the mounting screw holes on the side of the drive are used, then
use only the two pairs of outer holes. Do not use the centre hole
in conjunction with only one of the outer holes. The screw must not
penetrate the drive by more than 4.5 millimetres.

Grounding
---------
Sufficient grounding will be provided for correct operation when
the drive is screwed into an electrically grounded frame.

Cooling
-------
Allow space above and below the drive to provide for adequate air
flow. Fan cooling is recommended. The disk enclosure temperature,
measured at top centre, should never exceed 60*C.













TOP
previous page: Hard Drive: FUJITSU: M1603SAU > 11/1995 544MB 3.5"/SL    SCSI2 FAST
  
page up: Hard Drive Specs from FUJITSU
  
next page: Hard Drive: FUJITSU: M1606SAU < 11/1995 1091MB 3.5"/SL    SCSI2 FAST