lotus

previous page: Hard Drive: CONNER: CP-2024XT 21MB 2.5"/SSL   IDE / XT
  
page up: Hard Drive Specs from CONNER
  
next page: Hard Drive: CONNER: CP-2040 42MB 2.5"/SSL   SCSI1 SE

Hard Drive: CONNER: CP-2034 32MB 2.5"/SSL IDE / AT




C P - 2 0 3 4    CONNER
NO MORE PRODUCED                                      Native|  Translation
                                                      ------+-----+-----+-----
Form                 2.5"/SUPERSLIMLINE    Cylinders     823|  411|     |
Capacity form/unform    32/      MB        Heads           2|    4|     |
Seek time   / track  19.0/ 5.0 ms          Sector/track   38|   38|     |
Controller           IDE / AT              Precompensation
Cache/Buffer            32 KB LOOK-AHEAD   Landing Zone
Data transfer rate    1.500 MB/S int       Bytes/Sector      512
                      4.500 MB/S ext
Recording method     RLL 2/7                        operating  | non-operating
                                                  -------------+--------------
Supply voltage     5 V          Temperature *C         5 55    |    -40 60
Power: sleep          0.3 W     Humidity     %         8 80    |      8 80
       standby        0.4 W     Altitude    km    -0.061  3.050|        12.200
       idle           1.3 W     Shock        g        10       |    100
       seek           2.8 W     Rotation   RPM      3486
       read/write     2.8 W     Acoustic   dBA        34
       spin-up            W     ECC        Bit   22,REED SOLOMON
                                MTBF         h     100000
                                Warranty Month
Lift/Lock/Park     YES          Certificates     CSA,IEC435,UL478,VDE

Layout

CONNER CP2034/CP2064 PRODUCT MANUAL 00501-006

  +------------------------------------------------------+
  | +-+                                                  |X44
  | | |                                                I |XX Power
  | | |        E1   E2                                 N |XX +5V 41/42
  | +-+         +-+-+                                  T |XX GND 43
  |             | | |                                  E |XX
  |             +-+-+                                  R |XX
  |                                                    F |X* Position
  |                                                    A |XX 20-Key
  |                                                    C |XX
  |                                                    E |XX
  |                                                      |XX
  |                                                      |XX
  |                                                      |1X
  |                                                      |XX Factory
  |                                                      |XX test
  +------------------------------------------------------+   points

Jumpers

CONNER CP2034/CP2064 PRODUCT MANUAL 00501-006

Jumper setting
--------------

Interface Connector/Signal Levels
---------------------------------
All signal levels are TTL compatible. A logic "1" is > 2.0 Volts. A
logic "0" is from 0.00 Volts to 0.70 Volts. The drive capabolity of
each of the inbound signals is described below.

    +--------------------------------------------------------+
    | Pin    Signal             Pin     Signal               |
    +--------------------------------------------------------+
    | 01     -Reset             02      GND                  |
    +--------------------------------------------------------+
    | 03     +Data  7           04      +Data  8             |
    +--------------------------------------------------------+
    | 05     +Data  6           06      +Data  9             |
    +--------------------------------------------------------+
    | 07     +Data  5           08      +Data 10             |
    +--------------------------------------------------------+
    | 09     +Data  4           10      +Data 11             |
    +--------------------------------------------------------+
    | 11     +Data  3           12      +Data 12             |
    +--------------------------------------------------------+
    | 13     +Data  2           14      +Data 13             |
    +--------------------------------------------------------+
    | 15     +Data  1           16      +Data 14             |
    +--------------------------------------------------------+
    | 17     +Data  0           18      +Data 15             |
    +--------------------------------------------------------+
    | 19     GND                20      Key                  |
    +--------------------------------------------------------+
    | 21     Reserved           22      GND                  |
    +--------------------------------------------------------+
    | 23     -IOW               24      GND                  |
    +--------------------------------------------------------+
    | 25     -IOR               26      GND                  |
    +--------------------------------------------------------+
    | 27     IOCHRDY            28      Reserved             |
    +--------------------------------------------------------+
    | 29     Reserved           30      GND                  |
    +--------------------------------------------------------+
    | 31     +IRQ               32      -IO16                |
    +--------------------------------------------------------+
    | 33     +ADDR 1            34      -PDIAG               |
    +--------------------------------------------------------+
    | 35     +ADDR 0            36      +ADDR 2              |
    +--------------------------------------------------------+
    | 37     -CS0               38      -CS1                 |
    +--------------------------------------------------------+
    | 39     -Active            40      GND                  |
    +--------------------------------------------------------+
    | 41     5 Volts (Logic)    42      5 Volts (Motor)      |
    +--------------------------------------------------------+
    | 43     GND                44      Reserved             |
    +--------------------------------------------------------+

 E1/E2   Master/Slave
 --------------------
      E1   E2     For Master (C Drive) when E1 is CLOSED, place
      +-+         Jumper as shown.
      |*|  *
      |*|  *
      +-+

      E1   E2      For Slave (D Drive) when E2 is OPEN.
                   Store Jumper as shown.
       *   *
      +-----+
      |*   *|
      +-----+

The CP2034 and CP2064 drives are designed to operate either as a
Master drive (C Drive) or a Slave Drive (D Drive). This feature is
dependent on two drive settings; the status of hardware Jumper E1 and
the firmware setting of a feature bit. When (E1) is closed, and the
feature bit is set, the drive will assume the role of a Master Drive.
When E1 is open, and the feature reset, the drive will act as the
Slave. In single drive configurations E1 must remain in the closed
position.

Install

CONNER CP2034/CP2064 PRODUCT MANUAL 00501-006

Notes on installation
=====================

Installation direction
----------------------

     horizontally                           vertically
   +-----------------+             +--+                       +--+
   |                 |             |  +-----+           +-----+  |
   |                 |             |  |     |           |     |  |
 +-+-----------------+-+           |  |     |           |     |  |
 +---------------------+           |  |     |           |     |  |
                                   |  |     |           |     |  |
                                   |  |     |           |     |  |
 +---------------------+           |  +-----+           +-----+  |
 +-+-----------------+-+           +--+                       +--+
   |                 |
   |                 |
   +-----------------+

The drive may be mounted in any attitude!

Recommended Mounting Configuration
----------------------------------
This CP2034 and CP2064 are designed to be used in applications where
the unit may experience shock and vibrations at greater levels than
larger and heavier disk drives.

The design features which allow greater shock tolerance are the use
of rugged heads and media, a dedicated landing zone, closed loop
servo positioning and specially designed motor and actuator
assemblies.

Four (4) side mounting points and four (4) bottom mounting points are
provided to the customer. The drive is mounted using 3mm x 0.5mm
thread screw. The screw insertion depth should not exceed 4mm into
the mounting holes. The system integrator should allow ventilation
to the drive to ensure reliable drive operation over the operating
temperature range.

For additional vibration isolation, an external suspension system
may be used.

Interface Connector
-------------------
The CP2034 and CP2064 drives have a 44 pin right angle interface/
power connector mounted on the PCB. The recommended mating connector
is DuPont part number 69764-044 or equivalent. The maximum cable
lenght is two feet.

Magnetic Field
--------------
The externally induced magnetic flux density may not exceed 6 gauss
(DC - 700KHz) or 1.0 gauss (700KHz - 1.5MHz) as measured at the
drive surface.

Acoustic Sound Emission
-----------------------
Pressure: 34 dB(A) max at 1 meter.

Features

CONNER CP2034/CP2064 PRODUCT MANUAL 00501-006

Key Features
------------
The CP2034 and CP2064 are a high performance 2.5 inch low-profile
disk drives with formatted capacities of 32 and 64 megabytes
respectively. Both drives have 19 ms average seek time and are
designed to operate on IBM PC/AT or equivalent computers.
The drives feature a low 5V power requirement and high shock resist-
ance, enabling battery operation in a portable environment.

- 2.5" Form factor

- Single 5 Volt supply

- Low power requirements

 - High performance rotary voice coil actuator with embedded servo
   system.

- Single connector for power & interface

- Run length limited code (one of seven or two of seven)

- High shock resistance

- Internal air filtration system

- Sealed HDA

 - Automatic actuator latch over data free landing zone during standby
   mode or power-down

 - Microprocessor-controlled diagnostics routines that are auto-
   matically executed at start-up.

- Automatic error correction and retries

- Block size 512 bytes

- PC AT Interface

- 1:1 sector interleave

- Automativ read look ahead

- 32K Buffer

- Master/Slave

Universal Translate Mode
------------------------
Conner has established a Universal Translate Mode which enables the
user to configure the drive in an AT environment to any cylinder,
head, and sector configuration desired. The translate configuration
is limited only by the maximum capacity of the drive. Upon initial
power up to the drive it will default to a predetermined configura-
tion shown below:

          Cylinders        Heads       Sectors
 CP-2034     411             4           38
 CP-2064     823             4           38

After the drive is ready, the host system may issue INIT DRIVE PARMS
COMMAND (command code 91H) to alter the translate configuration
(number of heads and number of sectors per track). The drive para-
meters will then be saved in EEPROM for subsequent drive operations.

Seek Times
----------

       +----------------------------------+--------+
       |Physical track to track      max. |   5 ms |
       |Logical                      max. |  10 ms |
       +----------------------------------+--------+
       |               Average msec. typ. |  19    |
       |               Average msec. max. |  40    |
       +----------------------------------+--------+
       |Latency                msec. avg. |   8.7  |
       +----------------------------------+--------+
       The timing is measured through the interface with the drive
       operating at nominal DC input voltages. The timing also assumes
       that:
             - BIOS and PC system hardware dependency have been
               subtracted from timing measurements.

             - The drive is operated using its translation parameters.

       The average seek time is determined by averaging the seek time
       for a minimum of 1000 seeks of random length over the surface
       of the disk.

Functional Description
----------------------
The CP2034 and CP2064 contains all necessary mechanical and
electronic parts to interpret control signals, position the recording
heads over the desired track, read and write data, and provide a
contaminant free environment for the heads and disks.

Read/Write and Control Electronics
----------------------------------
One integrated circuit is mounted within the sealed enclosure in
close proximity to the read/write heads. Its function is to provide
head selection, read preamplification, and write drive circuitry.

The single microprocessor controlled circuit card provides the
remaining electronic functions which include:

        - Read/Write Circuitry
        - Rotary Actuator Control
        - Interface Control
        - Spin Speed Control
        - Dynamic Braking
        - Power Management

At power down or the start of STANDBY MODE or SLEEP MODE the heads
are automatically retracted to the inner diameter of the disk and
are latched and parked on a landing zone that is off the data tracks.

Drive Mechanism
---------------
A brushless DC direct drive motor rotates the spindle at 3486 RPMs.
The motor/spindle assembly is balanced to provide minimal mechanical
runout to the disks and to reduce vibration of the HDA. A dynamic
brake is used to provide a fast stop to the spindle motor when power
is removed, or upon initiation of STANDBY MODE.

Air Filtration System
---------------------
Within the sealed enclosure, a 0.3 micron filter which provides a
clean environment for the heads and disks.

Head Positioning Mechanism
--------------------------
The read/write heads for the CP2034 and CP2064 are supported by a
mechanism coupled to the voice coil actuator.

Read/Write Heads and Disks
--------------------------
Data is recorded on 95mm diameter thin film disk through micro-
miniature thin film or MIG heads.

Error Correction
----------------
The CP2034 and CP2064 drives use a Reed-Solomon code to perform
error detection and correction. The error correction polynominal is
capable of correcting one error burst with a maximum of 22 bits or
2 error bursts of up to 11 bits each, per 512 byte block. Single
bursts of 11 bits or less are corrected with no performance degrada-
tion.

Reliability and Maintenance
---------------------------
MTBF 100,000 hours POH
MTTR 10 minutes typical
Preventive Maintenance None
Component Design Life 5 years

Safety Standard
---------------
The CP2034 and CP2064 disk drives are designed to comply with
relevant prodcut safety standards such as:

 - UL 478, 5th edition, Standard for Safety of Information Processing
   and Business Equipment, and UL 1950, Standard for Safety of
   Information Technology Equipment

 - CSA 22.2#154, Data Processing Equipment and CSA 22.2#220, Inform-
   ation Processing and Business Equipment

 - IEC 435 Safety Requirements for Data Processing Equipment, IEC 380,
   Safety of Electrically Energized Office Machines, and IEC 950,
   Safety of Information Technology Equipment Including Electrical
   Business Equipment

 - VDE 0805 Equivalent to IEC 435, VDE 0805 TIEL 100, Equivalent to
   IEC 950, and VDE 0806, Equivalent to IEC 380













TOP
previous page: Hard Drive: CONNER: CP-2024XT 21MB 2.5"/SSL   IDE / XT
  
page up: Hard Drive Specs from CONNER
  
next page: Hard Drive: CONNER: CP-2040 42MB 2.5"/SSL   SCSI1 SE