lotus



previous page: Hard Drive: CONNER: CP-2024AT 21MB 2.5"/SSL   IDE / AT
  
page up: Hard Drive Specs from CONNER
  
next page: Hard Drive: CONNER: CP-2034 32MB 2.5"/SSL   IDE / AT

Hard Drive: CONNER: CP-2024XT 21MB 2.5"/SSL IDE / XT




C P - 2 0 2 4 X T    CONNER
NO MORE PRODUCED                                      Native|  Translation
                                                      ------+-----+-----+-----
Form                 2.5"/SUPERSLIMLINE    Cylinders     654|  615|     |
Capacity form/unform    21/      MB        Heads           2|    4|     |
Seek time   / track  23.0/ 5.0 ms          Sector/track   33|   17|     |
Controller           IDE / XT              Precompensation
Cache/Buffer             8 KB LOOK-AHEAD   Landing Zone
Data transfer rate    1.250 MB/S int       Bytes/Sector      512
                      3.750 MB/S ext
Recording method     RLL 2/7                        operating  | non-operating
                                                  -------------+--------------
Supply voltage     5 V          Temperature *C         5 55    |    -40 60
Power: sleep          0.3 W     Humidity     %         8 80    |      8 80
       standby        0.5 W     Altitude    km    -0.061  3.050|        12.200
       idle           1.5 W     Shock        g        10       |    100
       seek           3.0 W     Rotation   RPM      3433
       read/write     3.0 W     Acoustic   dBA        34
       spin-up            W     ECC        Bit   64
                                MTBF         h     100000
                                Warranty Month
Lift/Lock/Park     YES          Certificates     CSA,IEC435,UL478,VDE

Layout

CONNER CP2024 PRODUCT MANUAL 00501-005 10/1990, REV I

  +------------------------------------------------------+
  |                                                      |X44
  |                                                    I |XX Power
  | +-------+                                          N |XX +5V 41/42
  | +-------+                                          T |XX GND 43
  |                                                    E |XX
  |                                                    R |XX
  |                                                    F |X* Position
  |                                                    A |XX 20-Key
  |                                                    C |XX
  |                                                    E |XX
  |                                                      |XX
  |                                                      |XX
  |          E1 E2                                       |1X
  |           +++                                        |XX Factory
  |           +++                                        |XX test
  +------------------------------------------------------+   points

Jumpers

CONNER CP2024 PRODUCT MANUAL 00501-005 REV. I, 10/1990

Jumper setting
--------------

Interface Connector/Signal Levels
---------------------------------
All signal levels are TTL compatible. A logic "1" is > 2.0 Volts. A
logic "0" is from 0.00 Volts to 0.70 Volts. The drive capabolity of
each of the inbound signals is described below.

    +--------------------------------------------------------+
    | Pin    Signal             Pin     Signal               |
    +--------------------------------------------------------+
    | 01     -Reset             02      GND                  |
    +--------------------------------------------------------+
    | 03     +Data  7           04      +Data  8   (AT ONLY) |
    +--------------------------------------------------------+
    | 05     +Data  6           06      +Data  9   (AT ONLY) |
    +--------------------------------------------------------+
    | 07     +Data  5           08      +Data 10   (AT ONLY) |
    +--------------------------------------------------------+
    | 09     +Data  4           10      +Data 11   (AT ONLY) |
    +--------------------------------------------------------+
    | 11     +Data  3           12      +Data 12   (AT ONLY) |
    +--------------------------------------------------------+
    | 13     +Data  2           14      +Data 13   (AT ONLY) |
    +--------------------------------------------------------+
    | 15     +Data  1           16      +Data 14   (AT ONLY) |
    +--------------------------------------------------------+
    | 17     +Data  0           18      +Data 15   (AT ONLY) |
    +--------------------------------------------------------+
    | 19     GND                20      Key                  |
    +--------------------------------------------------------+
    | 21     Reserved           22      GND                  |
    +--------------------------------------------------------+
    | 23     -IOW               24      GND                  |
    +--------------------------------------------------------+
    | 25     -IOR               26      GND                  |
    +--------------------------------------------------------+
    | 27     -DACK (XT ONLY)    28      Reserved             |
    +--------------------------------------------------------+
    | 29     +DRQ  (XT ONLY)    30      GND                  |
    +--------------------------------------------------------+
    | 31     +IRQ               32      -IO16      (AT ONLY) |
    +--------------------------------------------------------+
    | 33     +ADDR 1            34      -PDIAG     (AT ONLY) |
    +--------------------------------------------------------+
    | 35     +ADDR 0            36      +ADDR 2    (AT ONLY) |
    +--------------------------------------------------------+
    | 37     -CS0               38      -CS1       (AT ONLY) |
    +--------------------------------------------------------+
    | 39     -Active            40      GND                  |
    +--------------------------------------------------------+
    | 41     5 Volts (Logic)    42      5 Volts (Motor)      |
    +--------------------------------------------------------+
    | 43     GND                44      -XT/AT               |
    +--------------------------------------------------------+

 MS/CD   Master/Slave
 --------------------
      E1   E2     For Master (C Drive) when E1 is CLOSED, place
      +-+         Jumper as shown.
      |*|  *
      |*|  *
      +-+

      E1   E2      For Slave (D Drive) when E1 is open. Store jumper
       *   *       as shown.
      +-----+
      |*   *|
      +-----+

The CP2024 drive is designed to operate either as a master drive (C
Drive) or a slave (D Drive) depending on the state of Jumper E1.
When E1 is closed, the drive will assume the role of master, when
open it will act as the slave. In single drive configurations E1
must be closed.

Install

CONNER CP2024 PRODUCT MANUAL 00501-005 REV. I, 10/1990

Notes on installation
=====================

Installation direction
----------------------

     horizontally                           vertically
   +-----------------+             +--+                       +--+
   |                 |             |  +-----+           +-----+  |
   |                 |             |  |     |           |     |  |
 +-+-----------------+-+           |  |     |           |     |  |
 +---------------------+           |  |     |           |     |  |
                                   |  |     |           |     |  |
                                   |  |     |           |     |  |
 +---------------------+           |  +-----+           +-----+  |
 +-+-----------------+-+           +--+                       +--+
   |                 |
   |                 |
   +-----------------+

Installation direction
----------------------
The drive may be mounted in any attitude!

Recommended Mounting Configuration
----------------------------------
The CP2024 is designed to be used in applications where the unit
may experience shock and vibrations at greater levels than larger
and heavier disk drives.

The design features which allow greater shock tolerance are the use
of rugged heads and media, a dedicated landing zone, closed loop
servo positioning and specially designed motor and actuator
assemblies.

Eigth (8) mounting points are provided to the customer. The drive is
mounted from the bottom using 4-40 screws 0.19 inch max. insertion.
Side mounting is also available using 2.5mm x 0.5 x 0.19 screws.
The system integrator should allow ventilation to the drive to ensure
reliable drive operation over the operating temperature range.

For additional vibration isolation, an external suspension system
may be used.

Interface Connector
-------------------
The CP2024 has a 44 pin right angle interface/power connector
mounted on the PCB. The recommended mating connector part number
from Elco Corporation for the Flat Ribbon type is 20-8394-2050-
02101S; and for Solder Tail type it is Vertical PCB 20-8390-2050-
00101. The maximum cable lenght is two feet.

Diagnostic Routines
-------------------
The microprocessor performs diagnostics upon application of power.
If an error is detected, the CP2024 will not come ready.

Magnetic Field
--------------
The disk drive will meet its specified performance while operating
in the presense of an externally produced magnetic field under the
following conditions:

     +-------------------+---------------------+
     | Frequency         | Field Intensity     |
     +-------------------+---------------------+
     | 0 to 1.5 MHz      | 6 gauss maximum     |
     +-------------------+---------------------+
     | 1.5 MHZ           | 1 gauss maximum     |
     +-------------------+---------------------+

Acoustic Sound Emission
-----------------------
Power - TBD
Pressure - 34 dBa at 1 meter

Installation of the Drive and Adapter Card
------------------------------------------
1. Remove power to the computer

  2. If another hard disk controller is installed, it is necessary to
     prevent it from responding to the addresses 1F0-7H and 3F6-7H.
     It is also necessary to ensure that the controller is
     electrically disconnected or tri-stated from IRQ14 of the mother-
     board bus. This may be done either by removing the board, by
     electrically disconnecting the signal from the interface, or by
     setting the jumpers of the board to disable the hard disk
     controller.

3. Insert the board into any available card slot.

  4. Configure the Host adapter for the correct configuration of your
     computer BIOS.

     Adapter Card Jumpers   E1 and E3 always not installed
                            E2 and E4 always installed

5. Connect power to the CP2024.

6. Run the DOS FDISK program to establish DOS partitions.

      Note: DOS 3.3 and below have limitations of 32 megabytes unless
            software utility is used to overcome this.

  7. Run the DOS format programm by typing "Format C:/S". The volume
     may be named with the addition of the "/V". The format will be
     completed and the system will ask for a volume name.

8. Files can then be copied to the C drive from floppy.

  9. When the system is rebooted, the system should boot from the hard
     drive (Drive C) if the floppy is removed.

Features

CONNER CP2024 PRODUCT MANUAL 00501-005 REV. I, 10/1990

Key Features
------------
The CP2024 is a high performance 2.5 inch low-profile (0.69")
21.4 megabyte (formatted) disk drive with average seek time not do
exceed 23ms which is designed to operate on IBM PC/XT & PC/AT or
equivalent computers. The drives feature a low 5V power requirement
and high shock resistance, enabling battery operation in portable
environments.

- 2.5" Form factor

- Single 5 Volt supply

- Low power requirements

- 6.0 oz

 - High performance rotary voice coil actuator with embedded servo
   system.

- Single connector for power & interface

- Run length limited code (1/7 or 2/7)

- High shock resistance

- Internal air filtration system

- Sealed HDA

 - Automatic actuator latch over data free landing zone during standby
   mode or power-down

 - Microprocessor-controlled diagnostics routines that are auto-
   matically executed at start-up.

- Automatic error correction and retries

- Block size 512 bytes

- PC XT/AT Interface (interface selectable)

- 1:1 sector interleave

- Look Ahead Read Capability

- 8K Buffer

- Master/Slave option

AT Mode
-------
The Host addresses the drive using programmed I/O. This method
requires that the desired register address be placed on the three
address lines A2-A0, a proper drive chip select is asserted and read
or write strobe (-IOR/-IOW) is given to the chip.

The Host generates two independent chip selects on the interface. The
high order chip select, -CS1, is used to access register 3F6 or 3F7.
The low order chip select, -CS0, is used to address registers 1F0 -
1F7.

The Host data bus 15-8 is only enabled when I016 enable is active and
the Host is addressing the data register for transferring data and
not the ECC bytes which are only transferred if the operation is read
or write long.

XT Mode
-------
The Host addresses the drive using programmed I/O. This method re-
quires that the desired register address be placed on the address
lines A1 - A0, a proper drive select is asserted and a read or write
strobe (-IOR/-IOW) is given to the drive. The drive is normally
decoded at base address 320H.

Seek Times
----------

       +----------------------------------+--------+
       |Physical track to track      max. |   8 ms |
       +----------------------------------+--------+
       | AT INTERFACE  Average msec.      |  23    |
       |               Average msec. max. |  40    |
       +----------------------------------+--------+
       |Latency                msec. avg. |   8.7  |
       +----------------------------------+--------+
       The timing is measured through the interface with the drive
       operating at nominal DC input voltages. The timing also assumes
       that:
             - BIOS and PC system hardware dependency have been
               subtracted from timing measurements.

             - The drive is operated using its translation parameters.

       The average seek time is determined by averaging the seek time
       for a minimum of 1000 seeks of random length over the surface
       of the disk.

Functional Description
----------------------
The CP2024 contains all necessary mechanical and electronic parts to
interpret control signals, position the recording heads over the
desired track, read and write data, and provide a contaminant free
environment for the heads and disks.

Read/Write and Control Electronics
----------------------------------
One integrated circuit is mounted within the sealed enclosure in
close proximity to the read/write heads. Its function is to provide
one of two head selection, read preamplification, and write drive
circuitry.

The single microprocessor controlled circuit card provides the
remaining electronic functions which include:

        - Read/Write Circuitry
        - Rotary Actuator Control
        - Interface Control
        - Spin Speed Control
        - Dynamic Braking
        - Power Management

At power down or the start of STANDBY MODE the heads are auto-
matically retracted to the inner diameter of the disk and are latched
and parked on a landing zone that is inside the data tracks.

Drive Mechanism
---------------
A brushless DC direct drive motor rotates the spindle at 3433 RPM.
The motor/spindle assembly is balanced to provide minimal mechanical
runout to the disks and to reduce vibration of the HDA. A dynamic
brake is used to provide a fast stop to the spindle motor when power
is removed, or upon initiation of STANDBY MODE.

Air Filtration System
---------------------
Within the sealed enclosure, a 0.3 micron filter which provides a
clean environment for the heads and disks.

Head Positioning Mechanism
--------------------------
The two read/write heads are supported by a mechanism coupled to the
voice coil actuator.

Read/Write Heads and Disks
--------------------------
Data is recorded on 65mm diameter disk through two miniature thin
film heads.

Error Correction
----------------
The CP2024 performs internal error correction. The error correction
polynominal is capable of correcting one error burst with a maximum
of 8 bits per 512 byte block.

 Reliability and Maintenance
 ---------------------------
 MTBF                     100,000 hours POH (population is min. of 100
                          units)
 MTTR                     10 minutes typical
 Preventive Maintenance   None
 Component Design Life    5 years

Safety Standard
---------------
The CP2024 disk drive is designed to comply with relevant product
safety standards such as:

 - UL 478, 5th edition, Standard for Safety of Information Processing
   and Business Equipment, and UL 1950, Standard for Safety of
   Information Technology Equipment

 - CSA 22.2#154, Data Processing Equipment and CSA 22.2#220,
   Information Processing and Business Equipment

 - IEC 435 Saftey Requirements for Data Processing Equipment,
   IEC 380, Safety of Electrically Energized Office Machines, and
   IEC 950, Safety of Information Technology Equipment Including
   Electrical Business Equipment

 - VDE 0805 Equivalent to IEC 435,
   VDE 0805 TIEL 100, Equivalent to IEC 950, and VDE 0806, Equivalent
   to IEC 380













TOP
previous page: Hard Drive: CONNER: CP-2024AT 21MB 2.5"/SSL   IDE / AT
  
page up: Hard Drive Specs from CONNER
  
next page: Hard Drive: CONNER: CP-2034 32MB 2.5"/SSL   IDE / AT