SUPER I/O (0002) Hard Disk/Floppy Controller Settings and Configuration
UNIDENTIFIED
SUPER I/O (0002)
Data bus: | 16-bit, ISA |
Size: | Half-length, half-height card |
Hard drive supported: | Two IDE (AT) Interface drives |
Floppy drives supported: | Two 360KB, 720KB, 1.2MB, or 1.44MB drives |
CONNECTIONS | |
Function | Location |
40-pin AT Interface (IDE) connector | CN1 |
34-pin control cable connector-floppy drive | CN2 |
10-pin serial port (COM2/4) - internal | CN3 |
10-pin serial port (COM1/3) - internal | CN4 |
15-pin game port - internal | CN5 |
25-pin parallel port (LPT2/3) - external | CN6 |
USER CONFIGURABLE SETTINGS | |||
Function | Location | Setting | |
| » | Hard drive enabled | JP1 | pins 2 & 3 closed |
Hard drive disabled | JP1 | pins 1 & 2 closed | |
| » | Floppy drive enabled | JP2 | pins 2 & 3 closed |
Floppy drive disabled | JP2 | pins 1 & 2 closed | |
| » | Serial Port 1 (CN4) is set to COM1 | JP3 | pins 2 & 3 closed |
Serial Port 1 (CN4) is set to COM3 | JP3 | pins 1 & 2 closed | |
| » | Serial Port 2 (CN3) is set to COM2 | JP4 | pins 2 & 3 closed |
Serial Port 2 (CN3) is set to COM4 | JP4 | pins 1 & 2 closed | |
| » | Parallel Port (CN6) is set to LPT2 | JP5 | pins 2 & 3 closed |
Parallel Port (CN6) is set to LPT3 | JP5 | pins 1 & 2 closed | |
USER CONFIGURABLE SETTINGS | |||
Function | Location | Setting | |
| » | Serial Port 1 (CN4) enabled | JP6 | pins 2 & 3 closed |
Serial Port 1 (CN4) disabled | JP6 | pins 1 & 2 closed | |
| » | Serial Port 2 (CN3) enabled | JP7 | pins 2 & 3 closed |
Serial Port 2 (CN3) disabled | JP7 | pins 1 & 2 closed | |
| » | Parallel Port (CN6) enabled | JP8 | pins 2 & 3 closed |
Parallel Port (CN6) disabled | JP8 | pins 1 & 2 closed | |
| » | Game Port (CN5) enabled | JP9 | pins 2 & 3 closed |
Game Port (CN5) disabled | JP9 | pins 1 & 2 closed | |
Serial Port 1 (CN4) uses IRQ9 | JP10 | pins 2 & 3 closed | |
Serial Port 2 (CN3) uses IRQ9 | JP10 | pins 1 & 2 closed | |
Serial Port 1 (CN4) uses IRQ3 | JP11 | pins 2 & 3 closed | |
| » | Serial Port 2 (CN3) uses IRQ3 | JP11 | pins 1 & 2 closed |
| » | Serial Port 1 (CN4) uses IRQ4 | JP12 | pins 2 & 3 closed |
Serial Port 2 (CN3) uses IRQ4 | JP12 | pins 1 & 2 closed | |
Serial Port 1 (CN4) uses IRQ5 | JP13 | pins 2 & 3 closed | |
Serial Port 2 (CN3) uses IRQ5 | JP13 | pins 1 & 2 closed | |
| » | Parallel Port (CN6) uses IRQ7 | JP14 | pins 1 & 2 closed |
Parallel Port (CN6) uses IRQ5 | JP14 | pins 2 & 3 closed | |
| » | I/O Channel Ready signal disabled | JP15 | open |
I/O Channel Ready signal enabled | JP15 | closed | |
My Books
