LCS-6624U/G Hard Disk/Floppy Controller Settings and Configuration
LONGSHINE MICROSYSTEM, INC.
LCS-6624U/G
Data bus: | 16-bit, ISA |
Size: | Half-length, full-height card |
Hard drive supported: | Two IDE(AT) or one IDE(XT) Interface drives |
Floppy drives supported: | Two 360KB, 720KB, 1.2MB, or 1.44MB drives |
CONNECTIONS | |
Function | Location |
16-pin game port - internal | CN1 |
40-pin IDE(AT) Interface connector | CN2 |
34-pin control cable connector-floppy drive | CN3 |
10-pin serial port (COM2/4) - internal | CN4 |
10-pin serial port (COM1/3) - external | CN5 |
25-pin parallel port (LPT1/2) - external | CN6 |
2-pin connector - Drive active LED | JP1 |
USER CONFIGURABLE SETTINGS | |||
Function | Location | Setting | |
| » | Game port enabled | JP2 | pins 1 & 2 closed |
Game port disabled | JP2 | pins 2 & 3 closed | |
| » | Hard drive controller installation installed | JP3 | pins 1 & 2 closed |
Hard drive controller installation not installed | JP3 | pins 2 & 3 closed | |
IDE drive mode is XT | JP4 | pins 1 & 2 closed | |
| » | IDE drive mode is AT | JP4 | pins 2 & 3 closed |
USER CONFIGURABLE SETTINGS | |||
Function | Location | Setting | |
| » | Hard drive port address is 3F6, 3F7, 1F0-1F7h | JP5 | pins 1 & 2 closed |
Hard drive port address is 376, 377, 170-177h | JP5 | pins 2 & 3 closed | |
| » | Hard drive enabled | JP6 | pins 1 & 2 closed |
Hard drive disabled | JP6 | pins 2 & 3 closed | |
| » | Floppy drive port address is 3F7, 1F7, 3F0-3F7h | JP7 | pins 1 & 2 closed |
Floppy drive port address is 377, 177, 370-377h | JP7 | pins 2 & 3 closed | |
| » | Floppy drive enabled | JP8 | pins 1 & 2 closed |
Floppy drive disabled | JP8 | pins 2 & 3 closed | |
| » | Serial Port 2 (CN4) is set to COM2 (2F8h) | JP12 | pins 1 & 2 closed |
Serial Port 2 (CN4) is set to COM4 (2E8h) | JP12 | pins 2 & 3 closed | |
| » | Serial Port 2 (CN4) enabled | JP13 | pins 1 & 2 closed |
Serial Port 2 (CN4) disabled | JP13 | pins 2 & 3 closed | |
| » | Serial Port 1 (CN5) is set to COM1 (3F8h) | JP14 | pins 1 & 2 closed |
Serial Port 1 (CN5) is set to COM3 (3E8h) | JP14 | pins 2 & 3 closed | |
| » | Serial Port 1 (CN5) enabled | JP15 | pins 1 & 2 closed |
Serial Port 1 (CN5) disabled | JP15 | pins 2 & 3 closed | |
| » | Parallel port (CN6) is set to LPT2 (378h) | JP16 | pins 1 & 2 closed |
Parallel port (CN6) is set to LPT3 (278h) | JP16 | pins 2 & 3 closed | |
| » | Parallel port (CN6) enabled | JP17 | pins 1 & 2 closed |
Parallel port (CN6) disabled | JP17 | pins 2 & 3 closed | |
| » | I/O Channel Ready disabled | JP18 | open |
I/O Channel Ready enabled | JP18 | closed | |
PARALLEL PORT (CN6) INTERRUPT REQUEST - JP9 | ||||||
IRQ | Jumper 1 | Jumper 2 | Jumper 3 | Jumper 4 | Jumper 5 | |
3 | closed | open | open | open | open | |
4 | open | closed | open | open | open | |
5 | open | open | closed | open | open | |
| » | 7 | open | open | open | closed | open |
9 | open | open | open | open | closed | |
SERIAL PORT 1 (CN5) INTERRUPT REQUEST - JP10 | ||||||
IRQ | Jumper 1 | Jumper 2 | Jumper 3 | Jumper 4 | Jumper 5 | |
3 | closed | open | open | open | open | |
| » | 4 | open | closed | open | open | open |
5 | open | open | closed | open | open | |
7 | open | open | open | closed | open | |
9 | open | open | open | open | closed | |
SERIAL PORT 2 (CN4) INTERRUPT REQUEST - JP11 | ||||||
IRQ | Jumper 1 | Jumper 2 | Jumper 3 | Jumper 4 | Jumper 5 | |
| » | 3 | closed | open | open | open | open |
4 | open | closed | open | open | open | |
5 | open | open | closed | open | open | |
7 | open | open | open | closed | open | |
9 | open | open | open | open | closed | |
My Books
