CSA-6210/KX Hard Disk/Floppy Controller Settings and Configuration

Data bus:	32-bit VESA
Size:	Full-length, full-height card
Hard drive supported:	Up to four IDE interface drives
Floppy drives supported:	360KB, 720KB, 1.2MB or 1.44MB drives

CONNECTIONS
Function	Location
40-pin IDE interface 1	CN1
40-pin IDE interface 2	CN2
34-pin control cable connector - floppy drive	CN3
16-pin connector - game port	CN4
10-pin connector - serial port 1	CN5
25-pin connector - external parallel port	CN6
10-pin connector - serial port 2	CN7
2-pin connector - drive active LED	LED

PRIMARY SERIAL PORT ADDRESS SELECT
COM		W1/A	W1/B
»	COM1	pins 2 & 3 closed	pins 1 & 2 closed
	COM3	pins 1 & 2 closed	pins 2 & 3 closed
	COM4	pins 2 & 3 closed	pins 2 & 3 closed
	Disabled	pins 1 & 2 closed	pins 1 & 2 closed

ALTERNATE SERIAL PORT ADDRESS SELECT
COM	W1/C	W1/D
COM2	pins 2 & 3 closed	pins 1 & 2 closed
COM3	pins 2 & 3 closed	pins 2 & 3 closed
COM4	pins 1 & 2 closed	pins 2 & 3 closed
Disabled	pins 1 & 2 closed	pins 1 & 2 closed

PARALLEL PORT CONFIGURATION
LPT		W1/E	W1/F
»	LPT1	pins 1 & 2 closed	pins 2 & 3 closed
	LPT2	pins 2 & 3 closed	pins 1 & 2 closed
	LPT3	pins 2 & 3 closed	pins 2 & 3 closed
	Disabled	pins 1 & 2 closed	pins 1 & 2 closed

PRIMARY SERIAL PORT INTERRUPT SELECT
IRQ		W2/A	W2/B	W2/C
»	IRQ4	closed	open	open
	IRQ3	open	closed	open
	IRQ5	open	open	closed

ALTERNATE SERIAL PORT INTERRUPT SELECT
IRQ		W2/D	W2/E	W2/F
»	IRQ3	closed	open	open
	IRQ4	open	closed	open
	IRQ5	open	open	closed

PARALLEL PORT INTERRUPT SELECT
IRQ		W2/G	W2/H
»	IRQ7	closed	open
	IRQ5	open	closed

SECONDARY IDE INTERFACE INTERRUPT SELECT
IRQ		W2/I	W2/J	W2/K	W2/L
»	IRQ15	open	open	open	closed
	IRQ10	closed	open	open	open
	IRQ11	open	closed	open	open
	IRQ12	open	open	closed	open

PARALLEL PORT INTERRUPT SELECT
IRQ		W2/G	W2/H
»	IRQ7	closed	open
	IRQ5	open	closed

SECONDARY IDE INTERFACE ADDRESS SELECT
Address		W3/A
»	17Xh	pins 2 & 3 closed
	1FXh	pins 1 & 2 closed

SECONDARY IDE INTERFACE CONFIGURATION
Setting		W3/B
»	Enabled	pins 2 & 3 closed
	Disabled	pins 1 & 2 closed

FLOPPY DRIVE ADDRESS SELECT
Address		W3/C
»	3Fxh	pins 1 & 2 closed
	37xh	pins 2 & 3 closed

FLOPPY DRIVE INTERFACE CONFIGURATION
Setting		W3/D
»	Enabled	pins 2 & 3 closed
	Disabled	pins 1 & 2 closed

PRIMARY IDE INTERFACE ADDRESS SELECT
Address		W4/A
»	1Fxh	open
	17xh	closed

CONFIG. PORT ADDRESS SELECT
Address		W4/B
»	078 - 7Ch	open
	178 - 17Ch	closed

CONFIG. PORT ADDRESS SELECT
Address		W4/B
»	078 - 7Ch	open
	178 - 17Ch	closed

FACTORY CONFIGURED SETTINGS
Jumper	Setting
W4/C	open
W4/D	closed

PRIMARY IDE INTERFACE CONFIGURATION
Setting		W4/E
»	Enabled	open
	Disabled	closed

GAME PORT CONFIGURATION
Setting		W5
»	Disabled	pins 2 & 3 closed
	Enabled	pins 1 & 2 closed
Note: The game port is available on some models only.