TC3045-UTP (REV. A) Network Card Settings and Configuration

THOMAS-CONRAD CORPORATION

TC3045-UTP (REV. A)

Card Type
Network Interface Card
NIC Type
TCNS
Maximum Onboard Memory
Unidentified
Boot ROM
Available
Network Transfer Rate
100Mbps
Topology
Star
Wiring Type
Unshielded twisted pair
Data Bus
16-bit ISA

CONNECTIONS
Function
Label
UTP connector
CN1

USER CONFIGURABLE SETTINGS
Function
Label
Position
»
16K Block decode size
SW1/2
On

128K Block decode size
SW1/2
Off
»
Factory configured - do not alter.
SW3/1
Unidentified
»
Enhanced operating mode
SW3/2
Off

Compatible operating mode
SW3/2
On

WAIT STATE SELECTION
Setting
SW1/1
»
0 Wait
Off

Wait
On

BASE I/O ADDRESS SELECTION
Setting
SW3/3
SW3/4
SW3/5
SW3/6
SW3/7
SW3/8
»
2E0h
Off
On
On
On
Off
On

2F0h
On
On
On
On
Off
On

300h
Off
Off
Off
Off
On
On

350h
On
Off
On
Off
On
On

BASE MEMORY ADDRESS SELECTION
Setting
SW1/3
SW1/4
SW1/5
SW1/6
SW1/7
SW1/8
»
D000h
Off
Off
On
Off
On
On

C000h
Off
Off
Off
Off
On
On

C400h
On
Off
Off
Off
On
On

C800h
Off
On
Off
Off
On
On

CC00h
On
On
Off
Off
On
On

D400h
On
Off
On
Off
On
On

D800h
Off
On
On
Off
On
On

DC00h
On
On
On
Off
On
On

E000h
Off
Off
Off
On
On
On

INTERRUPT SELECTION
Note: Configuration for IRQ selection (JP1) is unidentified.
Note: If you are installing the TC3045 in an 8-bit slot, make sure that the interrupt is set to 2/9, 3, 5, or 7. The TC3045 will not operate if the IRQ is set to any of the other settings.

NODE ADDRESS
Node
SW2/1
SW2/2
SW2/3
SW2/4
SW2/5
SW2/6
SW2/7
SW2/8
1
On
Off
Off
Off
Off
Off
Off
Off
2
Off
On
Off
Off
Off
Off
Off
Off
3
On
On
Off
Off
Off
Off
Off
Off
4
Off
Off
On
Off
Off
Off
Off
Off
251
On
On
Off
On
On
On
On
On
252
Off
Off
On
On
On
On
On
On
253
On
Off
On
On
On
On
On
On
254
Off
On
On
On
On
On
On
On
255
On
On
On
On
On
On
On
On
Note: Node 0 is reserved by the system and should not be used.
Note: A total of 255 base address settings are available. The switches are a binary representation of the decimal memory addresses. SW2/8 is the Most Significant Bit and switch SW2/1 is the Least Significant Bit. The switches have the following decimal values: SW2/8=128, SW2/7=64, SW2/6=32, SW2/5=16, SW2/4=8, SW2/3=4, SW2/2=2, SW2/1=1. Turn on the switches and add the values of the switches to obtain the correct memory address. (Off=0, On=1)

DIAGNOSTIC LED(S)
LED
Color
Status
Condition
LED1
Red
On
Data is being transmitted/received
LED1
Red
Blinking
Network connection is broken
LED1
Red
Off
Data is not being transmitted/received

Headaches Begone! A Systemic Approach To Healing Your Headaches

Don't Let Your Bike Seat Ruin Your Sex Life Book

TC3045-UTP (REV. A) Network Card Settings and Configuration

Search

My Books

Discover

Card Type	Network Interface Card
NIC Type	TCNS
Maximum Onboard Memory	Unidentified
Boot ROM	Available
Network Transfer Rate	100Mbps
Topology	Star
Wiring Type	Unshielded twisted pair
Data Bus	16-bit ISA

USER CONFIGURABLE SETTINGS
Function		Label	Position
»	16K Block decode size	SW1/2	On
	128K Block decode size	SW1/2	Off
»	Factory configured - do not alter.	SW3/1	Unidentified
»	Enhanced operating mode	SW3/2	Off
	Compatible operating mode	SW3/2	On

WAIT STATE SELECTION
Setting		SW1/1
»	0 Wait	Off
	Wait	On

BASE I/O ADDRESS SELECTION
Setting		SW3/3	SW3/4	SW3/5	SW3/6	SW3/7	SW3/8
»	2E0h	Off	On	On	On	Off	On
	2F0h	On	On	On	On	Off	On
	300h	Off	Off	Off	Off	On	On
	350h	On	Off	On	Off	On	On

BASE MEMORY ADDRESS SELECTION
Setting		SW1/3	SW1/4	SW1/5	SW1/6	SW1/7	SW1/8
»	D000h	Off	Off	On	Off	On	On
	C000h	Off	Off	Off	Off	On	On
	C400h	On	Off	Off	Off	On	On
	C800h	Off	On	Off	Off	On	On
	CC00h	On	On	Off	Off	On	On
	D400h	On	Off	On	Off	On	On
	D800h	Off	On	On	Off	On	On
	DC00h	On	On	On	Off	On	On
	E000h	Off	Off	Off	On	On	On

NODE ADDRESS
Node	SW2/1	SW2/2	SW2/3	SW2/4	SW2/5	SW2/6	SW2/7	SW2/8
1	On	Off	Off	Off	Off	Off	Off	Off
2	Off	On	Off	Off	Off	Off	Off	Off
3	On	On	Off	Off	Off	Off	Off	Off
4	Off	Off	On	Off	Off	Off	Off	Off
251	On	On	Off	On	On	On	On	On
252	Off	Off	On	On	On	On	On	On
253	On	Off	On	On	On	On	On	On
254	Off	On	On	On	On	On	On	On
255	On	On	On	On	On	On	On	On
Note: Node 0 is reserved by the system and should not be used. Note: A total of 255 base address settings are available. The switches are a binary representation of the decimal memory addresses. SW2/8 is the Most Significant Bit and switch SW2/1 is the Least Significant Bit. The switches have the following decimal values: SW2/8=128, SW2/7=64, SW2/6=32, SW2/5=16, SW2/4=8, SW2/3=4, SW2/2=2, SW2/1=1. Turn on the switches and add the values of the switches to obtain the correct memory address. (Off=0, On=1)

DIAGNOSTIC LED(S)
LED	Color	Status	Condition
LED1	Red	On	Data is being transmitted/received
LED1	Red	Blinking	Network connection is broken
LED1	Red	Off	Data is not being transmitted/received