TC5043-2 Network Card Settings and Configuration
THOMAS-CONRAD CORPORATION
TC5043-2
NIC Type | Ethernet |
Transfer Rate | 10Mbps |
Data Bus | 8/16-bit ISA |
Topology | Star |
Wiring Type | RG-58A/U 50ohm coaxial AUI transceiver via DB-15 port |
Boot ROM | Available |
INTERRUPT REQUEST | ||||||||||
IRQ | JP2 | JP3 | JP4 | JP5 | JP6 | JP7 | JP8 | JP9 | JP10 | |
| » | 3 | Open | Open | Open | Open | Open | Open | Open | Closed | Open |
2/9 | Open | Open | Open | Open | Open | Open | Open | Open | Closed | |
4 | Open | Open | Open | Open | Open | Open | Closed | Open | Open | |
| 5 | Open | Open | Open | Open | Open | Closed | Open | Open | Open | |
7 | Open | Open | Open | Open | Closed | Open | Open | Open | Open | |
10 | Open | Open | Open | Closed | Open | Open | Open | Open | Open | |
11 | Open | Open | Closed | Open | Open | Open | Open | Open | Open | |
12 | Open | Closed | Open | Open | Open | Open | Open | Open | Open | |
15 | Closed | Open | Open | Open | Open | Open | Open | Open | Open | |
I/O BASE ADDRESS | ||||
I/O Address | SW2/1 | SW2/2 | SW2/3 | |
| » | 300h | On | Off | Off |
| 100h | On | On | On | |
120h | On | On | Off | |
140h | On | Off | On | |
320h | Off | On | On | |
340h | Off | On | Off | |
360h | Off | Off | On | |
DRIVER TYPE | ||
Driver | SW1/1 | |
| » | NE2000 | On |
NE1000 | Off | |
TIMING COMPATIBILITY | ||
Setting | SW1/2 | |
| » | Normal | On |
C & T | Off | |
Note: The Compaq portable 286, IBM PS/2 Model 30-286 & any computer utilizing a C & T chipset, must be set to C & T timing compatibility. | ||
BOOT ROM | ||
Setting | SW2/7 | |
| » | Disabled | Off |
Enabled | On | |
BASE MEMORY ADDRESS | ||||
Memory Address | SW2/4 | SW2/5 | SW2/6 | |
| » | D000h | Off | On | On |
C400h | On | On | Off | |
C800h | On | Off | On | |
CC00h | On | Off | Off | |
D400h | Off | On | Off | |
D800h | Off | Off | On | |
DC00h | Off | Off | Off | |
CABLE TYPE | |||||||
Type | JP16 | JP17 | JP18 | JP19 | JP20 | JP21 | JP22 |
RG58A/U 50ohm | Closed | Pins 1 & 2 | Pins 1 & 2 | Pins 1 & 2 | Pins 1 & 2 | Pins 1 & 2 | Pins 1 & 2 |
AUI transceiver | Open | Pins 2 & 3 | Pins 2 & 3 | Pins 2 & 3 | Pins 2 & 3 | Pins 2 & 3 | Pins 2 & 3 |
Note: Pins designated should be in the closed position. | |||||||
DIAGNOSTIC LED(S) | |||
LED | Color | Status | Condition |
LED1 | Yellow | On | Data is being transmitted |
LED1 | Yellow | Off | Data is not being transmitted |
LED2 | Green | On | Data is being received |
LED2 | Green | Off | Data is not being received |
LED3 | Yellow | On | Collision detected on network |
LED3 | Yellow | Off | No collisions detected on network |
LED4 | Green | On | 10BASE-T link integrity exists |
LED4 | Green | On | 10BASE-T link integrity broken |
BUS SPEED | ||||
Speed | SW1/3 | SW1/4 | SW1/5 | |
| » | Normal | Off | Off | Off |
6/8MHz | Off | Off | On | |
10MHz | Off | On | Off | |
12/16MHz | On | Off | Off | |
FACTORY CONFIGURED SETTINGS - DO NOT ALTER | |
Jumper | Setting |
JP11 | Unidentified |
JP12 | Unidentified |
JP13 | Unidentified |
JP14 | Unidentified |
JP15 | Unidentified |
SW2/8 | On |
My Books
