TC6242-AIO Network Card Settings and Configuration

THOMAS-CONRAD CORPORATION

TC6242-AIO

NIC Type
ARCnet
Transfer Rate
2.5Mbps
Data Bus
8-bit ISA
Topology
Star
Linear Bus
Wiring Type
RG62A/U, 93ohm coaxial
Shielded twisted pair
Unshielded twisted pair
Twisted pair plus
Boot ROM
Available

NODE ADDRESS
Node
SW2/1
SW2/2
SW2/3
SW2/4
SW2/5
SW2/6
SW2/7
SW2/8
0
-
-
-
-
-
-
-
-
1
Off
On
On
On
On
On
On
On
2
On
Off
On
On
On
On
On
On
3
Off
Off
On
On
On
On
On
On
4
On
On
Off
On
On
On
On
On
251
Off
Off
On
Off
Off
Off
Off
Off
252
On
On
Off
Off
Off
Off
Off
Off
253
Off
On
Off
Off
Off
Off
Off
Off
254
On
Off
Off
Off
Off
Off
Off
Off
255
Off
Off
Off
Off
Off
Off
Off
Off
Note:Node address 0 is used for messaging between nodes and must not be used.
A total of 255 node address settings are available. The switches are a binary representation of the decimal node addresses. Switch 1 is the Least Significant Bit and switch 8 is the Most Significant Bit. The switches have the following decimal values: switch 1=1, 2=2, 3=4, 4=8, 5=16, 6=32, 7=64, 8=128. Turn off the switches and add the values of the off switches to obtain the correct node address. (On=0, off=1)

INTERRUPT REQUEST
IRQ
JP1
JP2
JP3
JP4
JP5
»
2
Open
Open
Open
Open
Closed

3
Closed
Open
Open
Open
Open

4
Open
Closed
Open
Open
Open

5
Open
Open
Closed
Open
Open

7
Open
Open
Open
Closed
Open

RESPONSE AND RECONFIGURATION TIMEOUTS
Setting
JP6
JP7
»
Network cable distance under 20,000 feet
Open
Open

Network cable distance greater than 20,000 feet
Closed
Closed

Note :All NICs on the network must have this option set the same

CABLE TYPE
Type
JP8
JP9
JP10
JP12
JP13
JP14
JP15
»
Coax (Star)
Pins 1 & 2
Pins 1 & 2
Pins 1 & 2
Pins 2 & 3
Pins 1 & 2
Pins 1 & 2
Pins 1 & 2

Coax (Bus)
Pins 1 & 2
Pins 1 & 2
Pins 1 & 2
Pins 2 & 3
Pins 2 & 3
Pins 1 & 2
Pins 1 & 2

Twisted pair+
Pins 2 & 3
Pins 2 & 3
Pins 2 & 3
Pins 1 & 2
Pins 1 & 2
Pins 2 & 3
Pins 2 & 3

Twisted pair
Pins 1 & 2
Pins 1 & 2
Pins 1 & 2
Pins 1 & 2
Pins 2 & 3
Pins 2 & 3
Pins 2 & 3

Note : Pins designated should be in the closed position

BASE MEMORY ADDRESS
Memory Address
SW1/1
SW1/2
SW1/3
SW1/4
SW1/5
SW1/6
»
D000h
Off
Off
On
Off
On
On

C000h
Off
Off
On
On
On
On

C400h
Off
Off
On
On
On
Off

C800h
Off
Off
On
On
Off
On

CC00h
Off
Off
On
On
Off
Off

D400h
Off
Off
On
Off
On
Off

D800h
Off
Off
On
Off
Off
On

DC00h
Off
Off
On
Off
Off
Off

COMPATABILITY MODE
Setting
SW1/8
»
Enhanced mode
On

Compatible mode
Off
Note: Enhanced mode optimizes performance and minimizes conflicts of your hardware by using a Thomas-Conrad

I/O BASE ADDRESS
Address
SW3/3
SW3/4
SW3/5
SW3/6
SW3/7
SW3/8
»
2E0h
Off
On
Off
Off
Off
On

2F0h
Off
On
Off
Off
Off
Off

300h
Off
Off
On
On
On
On

310h
Off
Off
On
On
On
Off

320h
Off
Off
On
On
Off
On

330h
Off
Off
On
On
Off
Off

340h
Off
Off
On
Off
On
On

350h
Off
Off
On
Off
On
Off

360h
Off
Off
On
Off
Off
On

370h
Off
Off
On
Off
Off
Off

380h
Off
Off
Off
On
On
On

390h
Off
Off
Off
On
On
Off

3A0h
Off
Off
Off
On
Off
On

3B0h
Off
Off
Off
On
Off
Off

3C0h
Off
Off
Off
Off
On
On

3D0h
Off
Off
Off
Off
On
Off

3E0h
Off
Off
Off
Off
Off
On

3F0h
Off
Off
Off
Off
Off
Off

FACTORY CONFIGURED SETTINGS - DO NOT ALTER
Switch
Setting
SW3/1
On
SW3/2
Off

DIAGNOSTIC LED(S)
LED
Status
Condition
LED1
On
Data is being transmitted/received.
LED1
Off
Data is not being transmitted/received.

Headaches Begone! A Systemic Approach To Healing Your Headaches

Don't Let Your Bike Seat Ruin Your Sex Life Book

TC6242-AIO Network Card Settings and Configuration

Search

My Books

Discover

NIC Type	ARCnet
Transfer Rate	2.5Mbps
Data Bus	8-bit ISA
Topology	Star Linear Bus
Wiring Type	RG62A/U, 93ohm coaxial Shielded twisted pair Unshielded twisted pair Twisted pair plus
Boot ROM	Available

NODE ADDRESS
Node	SW2/1	SW2/2	SW2/3	SW2/4	SW2/5	SW2/6	SW2/7	SW2/8
0	-	-	-	-	-	-	-	-
1	Off	On	On	On	On	On	On	On
2	On	Off	On	On	On	On	On	On
3	Off	Off	On	On	On	On	On	On
4	On	On	Off	On	On	On	On	On
251	Off	Off	On	Off	Off	Off	Off	Off
252	On	On	Off	Off	Off	Off	Off	Off
253	Off	On	Off	Off	Off	Off	Off	Off
254	On	Off	Off	Off	Off	Off	Off	Off
255	Off	Off	Off	Off	Off	Off	Off	Off
Note:Node address 0 is used for messaging between nodes and must not be used. A total of 255 node address settings are available. The switches are a binary representation of the decimal node addresses. Switch 1 is the Least Significant Bit and switch 8 is the Most Significant Bit. The switches have the following decimal values: switch 1=1, 2=2, 3=4, 4=8, 5=16, 6=32, 7=64, 8=128. Turn off the switches and add the values of the off switches to obtain the correct node address. (On=0, off=1)

INTERRUPT REQUEST
IRQ		JP1	JP2	JP3	JP4	JP5
»	2	Open	Open	Open	Open	Closed
	3	Closed	Open	Open	Open	Open
	4	Open	Closed	Open	Open	Open
	5	Open	Open	Closed	Open	Open
	7	Open	Open	Open	Closed	Open

RESPONSE AND RECONFIGURATION TIMEOUTS
Setting		JP6	JP7
»	Network cable distance under 20,000 feet	Open	Open
	Network cable distance greater than 20,000 feet	Closed	Closed
	Note :All NICs on the network must have this option set the same

CABLE TYPE
Type		JP8	JP9	JP10	JP12	JP13	JP14	JP15
»	Coax (Star)	Pins 1 & 2	Pins 1 & 2	Pins 1 & 2	Pins 2 & 3	Pins 1 & 2	Pins 1 & 2	Pins 1 & 2
	Coax (Bus)	Pins 1 & 2	Pins 1 & 2	Pins 1 & 2	Pins 2 & 3	Pins 2 & 3	Pins 1 & 2	Pins 1 & 2
	Twisted pair+	Pins 2 & 3	Pins 2 & 3	Pins 2 & 3	Pins 1 & 2	Pins 1 & 2	Pins 2 & 3	Pins 2 & 3
	Twisted pair	Pins 1 & 2	Pins 1 & 2	Pins 1 & 2	Pins 1 & 2	Pins 2 & 3	Pins 2 & 3	Pins 2 & 3
	Note : Pins designated should be in the closed position

BASE MEMORY ADDRESS
Memory Address		SW1/1	SW1/2	SW1/3	SW1/4	SW1/5	SW1/6
»	D000h	Off	Off	On	Off	On	On
	C000h	Off	Off	On	On	On	On
	C400h	Off	Off	On	On	On	Off
	C800h	Off	Off	On	On	Off	On
	CC00h	Off	Off	On	On	Off	Off
	D400h	Off	Off	On	Off	On	Off
	D800h	Off	Off	On	Off	Off	On
	DC00h	Off	Off	On	Off	Off	Off

COMPATABILITY MODE
Setting		SW1/8
»	Enhanced mode	On
	Compatible mode	Off
Note: Enhanced mode optimizes performance and minimizes conflicts of your hardware by using a Thomas-Conrad

I/O BASE ADDRESS
Address		SW3/3	SW3/4	SW3/5	SW3/6	SW3/7	SW3/8
»	2E0h	Off	On	Off	Off	Off	On
	2F0h	Off	On	Off	Off	Off	Off
	300h	Off	Off	On	On	On	On
	310h	Off	Off	On	On	On	Off
	320h	Off	Off	On	On	Off	On
	330h	Off	Off	On	On	Off	Off
	340h	Off	Off	On	Off	On	On
	350h	Off	Off	On	Off	On	Off
	360h	Off	Off	On	Off	Off	On
	370h	Off	Off	On	Off	Off	Off
	380h	Off	Off	Off	On	On	On
	390h	Off	Off	Off	On	On	Off
	3A0h	Off	Off	Off	On	Off	On
	3B0h	Off	Off	Off	On	Off	Off
	3C0h	Off	Off	Off	Off	On	On
	3D0h	Off	Off	Off	Off	On	Off
	3E0h	Off	Off	Off	Off	Off	On
	3F0h	Off	Off	Off	Off	Off	Off

FACTORY CONFIGURED SETTINGS - DO NOT ALTER
Switch	Setting
SW3/1	On
SW3/2	Off

DIAGNOSTIC LED(S)
LED	Status	Condition
LED1	On	Data is being transmitted/received.
LED1	Off	Data is not being transmitted/received.