SCRAMNET+ REHOSTABLE ADAPTER EVALUATION BOARD Network Card Settings and Configuration

NIC Type	Proprietary
Chipset	Systran Corporation
Maximum Onboard Memory	2MB DRAM (on daughterboard)
I/O Options	Bypass connector
Network Transfer Rate	150Mbps
Data Bus	VME double
Topology	Linear Bus/Ring
Wire Type	RG-58A/U 50ohm coaxial Fiber optic cable
Boot ROM	Not available

CONNECTIONS
Function	Label	Function	Label
Header to daughterboard J1B	J1A	Testing pins	J7
Header to main board J1A	J1B	Media board header	J10
Header to daughterboard J2B	J2A	Bypass connector	J13
Header to main board J2A	J2B	RG-58A/U 50ohm coaxial receive connector 1	W1A
Header to daughterboard J3B	J3A	Fiber optic ST receive connector 1	W1B
Header to main board J3A	J3B	Fiber optic SC receive connector 1	W1C
Unidentified	J4	RG-58A/U 50ohm coaxial receive connector 2	W2A
Testing pins	J6	Fiber optic ST receive connector 2	W2B
Fiber optic SC receive connector 2	W2C	Fiber optic ST transmit connector 2	W4B
RG-58A/U 50ohm coaxial transmit connector 1	W3A	Fiber optic SC transmit connector 2	W4C
Fiber optic ST transmit connector 1	W3B	Header to main board J10	W5A
Fiber optic SC transmit connector 1	W3C	Header to main board J10	W5B
RG-58A/U 50ohm coaxial transmit connector 2	W4A	Header to main board J10	W5C

USER CONFIGURABLE SETTINGS
Setting		Label	Position
»	Media card power source is internal	H2A	Pins 1 & 2 closed
	Media card power source is external	H2A	Pins 2 & 3 closed
»	Media card power source is internal	H2B	Pins 1 & 2 closed
	Media card power source is external	H2B	Pins 2 & 3 closed
	EEPROM write protect disabled	J4B	Pins 3 & 4 closed
	EEPROM write protect enabled	J4B	Pins 1 & 2 closed
»	Address bits for internal CSR enabled	J5	Closed
	Address bits for internal CSR disabled	J5	Open
	EEPROM read protect disabled	J5B	Pins 3 & 4 closed
	EEPROM read protect enabled	J5B	Pins 1 & 2 closed
»	Address bits for memory enabled	J8	Closed
	Address bits for memory disabled	J8	Open
»	Address bits for external CSR enabled	J9	Closed
	Address bits for external CSR disabled	J9	Open
»	TRIG1/TRIG2	J11	Unidentified
	Chassis ground connected to signal ground	J12	Pins 3 & 4 closed
	Chassis ground not connected to signal ground	J12	Pins 1 & 2 closed

DRAM CONFIGURATION

512KB, 1MB, or 2MB of memory may be factory installed on the daughterboard. The circuitry supports up to 8MB of memory. For other memory configurations, the user must provide an external memory interface.

CSR ADDRESS SELECTION
Setting		S1
»	00h, 20h	Position 0
	40h, 60h	Position 4
	80h, 80h	Position 8
	C0h, E0h	Position C

DIAGNOSTIC LED(S)
LED	Color	Status	Condition
LED1	Green	On	Network connection is good
LED1	Green	Off	Network connection is broken
LED2	Green	On	Message is waiting in transmit FIFO
LED2	Green	Off	Message is not waiting in transmit FIFO
LED3	Green	On	Carrier signal is detected
LED3	Green	Off	Carrier signal is not detected
LED4	Yellow	On	Error condition detected
LED4	Yellow	Off	Error condition not detected
LED5	Green	On	Message received from this node
LED5	Green	Off	Message not received from this node
LED6	Green	On	Message received from another node
LED6	Green	Off	Message not received from another node

MISCELLANEOUS TECHNICAL NOTE

The daughterboard is designed as a prototyping card for the user to design a VME bus network interface around. The main board shown above is only an evaluation board and is a separate product.