PRONET-4/16 MODEL P1390 Network Card Settings and Configuration
PROTEON, INC.
PRONET-4/16 MODEL P1390
NIC Type | Token-Ring |
Transfer Rate | 4/16Mbps |
Data Bus | 16-bit ISA |
Topology | Ring |
Wiring Type | Unshielded twisted pair Shielded twisted pair |
Boot ROM | Available |
BOOT ROM | ||
Setting | JP1 | |
| » | Disabled | Closed |
Enabled | Open | |
INTERRUPT REQUEST | |||||||||
IRQ | JP2A | JP2B | JP2C | JP2D | JP2E | JP2F | JP2G | JP2H | JP2I |
2/9 | Open | Open | Open | Closed | Open | Open | Open | Open | Open |
3 | Open | Open | Open | Open | Open | Open | Open | Open | Closed |
4 | Open | Open | Open | Open | Open | Open | Open | Closed | Open |
5 | Open | Open | Open | Open | Open | Open | Closed | Open | Open |
6 | Open | Open | Open | Open | Open | Closed | Open | Open | Open |
7 | Open | Open | Open | Open | Closed | Open | Open | Open | Open |
10 | Open | Open | Closed | Open | Open | Open | Open | Open | Open |
11 | Open | Closed | Open | Open | Open | Open | Open | Open | Open |
12 | Closed | Open | Open | Open | Open | Open | Open | Open | Open |
SA ADDRESS ENABLE (SAEN) | ||
Mode | JP3 | |
| » | SAEN enabled | Closed |
SAEN disabled | Open | |
Note:The SAEN jumper is provided for systems that are not 100% ISA compatible. If the you get a DMA data error or if the card fails to initialize, you should disabled SAEN.
| ||
I/O BASE ADDRESS | |||||||||
Address | JP4A | JP4B | JP4C | JP4D | JP4E | JP4F | JP4G | JP4H | |
0120h | Closed | Closed | Closed | Closed | Closed | Closed | Closed | Open | |
0220h | Closed | Closed | Closed | Closed | Closed | Closed | Open | Closed | |
0320h | Closed | Closed | Closed | Closed | Closed | Closed | Open | Open | |
0420h | Closed | Closed | Closed | Closed | Closed | Open | Closed | Closed | |
| » | 0A20h | Closed | Closed | Closed | Closed | Open | Closed | Open | Closed |
FC20h | Open | Open | Open | Open | Open | Open | Closed | Closed | |
FD20h | Open | Open | Open | Open | Open | Open | Closed | Open | |
FE20h | Open | Open | Open | Open | Open | Open | Open | Closed | |
FF20h | Open | Open | Open | Open | Open | Open | Open | Open | |
Note: A total of 255 I/O address settings are available. The switches are a binary representation of the two most significant digits in the Hexadecimal I/O address, the two least significant bits are set at 0020h. JP4H is the Least Significant Bit and JP4A is the Most Significant Bit. The jumpers have the following decimal values: jumper H=1, G=2, F=4, E=8, D=16, C=32, B=64, A=128. open the jumpers and add the values of the open jumpers. Convert that number to a hexadecimal number, and use it as the two left most digits in the numer "xx20h". If using Banyan VINES network, the I/O addresses are limited to the range between and including 0120h to 0F20h. | |||||||||
DMA CHANNEL | ||||
Channel | JP5A & JP5B | JP5C & JP5D | JP5E & JP5F | |
| » | DMA5 | Open | Open | Closed |
DMA6 | Open | Closed | Open | |
DMA7 | Closed | Open | Open | |
DMA CLOCK | |||||
Speed | JP6A | JP6B | JP6C | JP6D | |
| » | Bus speed | Open | Open | Open | Closed |
4MHz | Open | Open | Closed | Open | |
8MHz | Open | Closed | Open | Open | |
16MHz | Closed | Open | Open | Open | |
My Books
