2000T V2.4, EN-6360 V2.4 Network Card Settings and Configuration
EDIMAX COMPUTER COMPANY
2000T V2.4, EN-6360 V2.4
NIC Type | Ethernet |
Transfer Rate | 10Mbps |
Data Bus | 16-bit ISA |
Topology | Star |
Wiring Type | Unshielded twisted pair AUI transceiver via DB-15 port |
Boot ROM | Available |
COMPATIBILITY MODE | ||
Setting | JP1 | |
| » | Disabled | Pins 1 & 2 closed |
Enabled | PIns 2 & 3 closed | |
Note: On some systems the data bus timing is not truly IBM PC/AT compatible. If the card is not initializing, enabling the compatibility mode may allow the card to function properly. | ||
INTERRUPT SETTINGS | |||||||||||
IRQ | JP2A | JP2B | JP2C | JP2D | JP2E | JP2F | JP2G | JP2H | JP2I | JP2J | JP2K |
2/9 | Open | Open | Open | Open | Open | Closed | Open | Open | Open | Open | Open |
3 | Open | Open | Open | Open | Open | Open | Open | Open | Open | Open | Closed |
4 | Open | Open | Open | Open | Open | Open | Open | Open | Open | Closed | Open |
5 | Open | Open | Open | Open | Open | Open | Open | Open | Closed | Open | Open |
6 | Open | Open | Open | Open | Open | Open | Open | Closed | Open | Open | Open |
7 | Open | Open | Open | Open | Open | Open | Closed | Open | Open | Open | Open |
10 | Open | Open | Open | Open | Closed | Open | Open | Open | Open | Open | Open |
11 | Open | Open | Open | Closed | Open | Open | Open | Open | Open | Open | Open |
12 | Open | Open | Closed | Open | Open | Open | Open | Open | Open | Open | Open |
14 | Open | Closed | Open | Open | Open | Open | Open | Open | Open | Open | Open |
15 | Closed | Open | Open | Open | Open | Open | Open | Open | Open | Open | Open |
I/O BASE ADDRESS | |||
Address | JP2L | JP2M | |
| » | 300h | Closed | Closed |
320h | Closed | Open | |
340h | Open | Closed | |
360h | Open | Open | |
BOOT ROM | ||
Setting | JP3 | |
| » | Disabled | Open |
Enabled | Closed | |
BOOT ROM ADDRESS | |||||
Address | JP4A | JP4B | JP4C | JP4D | |
C0000h | Closed | Closed | Closed | Closed | |
C4000h | Closed | Closed | Closed | Open | |
| » | C8000h | Closed | Closed | Open | Closed |
CC000h | Closed | Closed | Open | Open | |
D0000h | Closed | Open | Closed | Closed | |
D4000h | Closed | Open | Closed | Open | |
D8000h | Closed | Open | Open | Closed | |
DC000h | Closed | Open | Open | Open | |
SIGNAL QUALITY ERROR (SQE) TEST | ||
Setting | JP5 | |
| » | Enabled | Pins 1 & 2 closed |
Disabled | Pins 2 & 3 closed | |
Note:Signal Quality Error (SQE) is a test of the collision circuitry and path. Link integrity must be enabled for SQE to be enabled. | ||
CABLE LENGTH SELECT | ||
Setting | JP7 | |
| » | 185meters | Pins 1 & 2 closed |
305meters | Pins 2 & 3 closed | |
Note: All cards on the network segment must have this option set the same. Link integrity must be enabled to select long cable length. | ||
LINK INTEGRITY | ||
Setting | JP8 | |
| » | Enabled | Pins 2 & 3 closed |
Disabled | Pins 1 & 2 closed | |
Note:If this option is disabled, SQE is also disabled and Cable Length is set to 185 meters. | ||
CABLE TYPE | ||
Type | JP9A - JP9F | JP10 |
AUI transceiver via DB-15 port | Open | Pins 1 & 2 closed |
Unshielded twisted pair | Closed | Pins 2 & 3 closed |
AUTOPOLARITY | ||
Setting | JP14 | |
| » | Enabled | Pins 1 & 2 closed |
Disabled | Pins 2 & 3 closed | |
Note: When disabled, if the network wire polarities are reversed, the card will be damaged. | ||
FACTORY CONFIGURED SETTINGS | |
Jumper | Setting |
JP6 | Unused |
CONNECTORS | |
Setting | Location |
External power LED. | JP11 |
DIAGNOSTIC LED(S) | |||
LED | Color | Status | Condition |
LED1 | Yellow | Off | Normal operation |
LED1 | Yellow | On | A reversed twisted pair is detected and corrected |
LED2 | Green | On | Twisted pair network connection is good |
LED2 | Green | Off | Twisted pair network connection is broken |
My Books
