1000T V2.4 Network Card Settings and Configuration
EDIMAX COMPUTER COMPANY
1000T V2.4
NIC Type | Ethernet |
Transfer Rate | 10Mbps |
Data Bus | 8-bit ISA |
Topology | Star |
Wiring Type | Unshielded twisted pair AUI transceiver via DB-15 port |
Boot ROM | Available |
I/O BASE ADDRESS | ||||
Address | JP1A | JP1B | JP1C | |
| » | 300h | Closed | Closed | Closed |
320h | Closed | Closed | Open | |
340h | Closed | Open | Closed | |
360h | Closed | Open | Open | |
INTERRUPT SETTINGS | ||||||
IRQ | JP1D | JP1E | JP1F | JP1G | JP1H | JP1I |
2 | Closed | Open | Open | Open | Open | Open |
3 | Open | Closed | Open | Open | Open | Open |
4 | Open | Open | Closed | Open | Open | Open |
5 | Open | Open | Open | Closed | Open | Open |
6 | Open | Open | Open | Open | Closed | Open |
7 | Open | Open | Open | Open | Open | Closed |
DMA CHANNEL | |||||
Channel | JP1J | JP1K | JP1L | JP1M | |
| » | Disabled | Closed | Open | Closed | Open |
DMA1 | Closed | Open | Closed | Open | |
DMA3 | Open | Closed | Open | Closed | |
CONNECTORS | |
Setting | Location |
External power LED. | JP2 |
BOOT ROM ADDRESS | |||||
Address | JP3A | JP3B | JP3C | JP3D | |
C0000h | Closed | Closed | Closed | Closed | |
C4000h | Open | Closed | Closed | Closed | |
| » | C8000h | Closed | Open | Closed | Closed |
CC000h | Open | Open | Closed | Closed | |
D0000h | Closed | Closed | Open | Closed | |
D4000h | Open | Closed | Open | Closed | |
D8000h | Closed | Open | Open | Closed | |
DC000h | Open | Open | Open | Closed | |
BOOT ROM | ||
Setting | JP5 | |
| » | Disabled | Open |
Enabled | Closed | |
AUTOPOLARITY | ||
Setting | JP6 | |
| » | Enabled | Pins 1 & 2 closed |
Disabled | Pins 2 & 3 closed | |
Note: When disabled, if the network wire polarities are reversed, the card will be damaged. | ||
LINK INTEGRITY | ||
Setting | JP7 | |
| » | Enabled | Pins 2 & 3 closed |
Disabled | Pins 1 & 2 closed | |
Note:If this option is disabled, SQE is also disabled and Cable Length is set to 185 meters. | ||
SIGNAL QUALITY ERROR (SQE) TEST | ||
Setting | JP8 | |
| » | Enabled | Pins 1 & 2 closed |
Disabled | Pins 2 & 3 closed | |
Note:Signal Quality Error (SQE) is a test of the collision circuitry and path. Link integrity must be enabled for SQE to be enabled. | ||
CABLE TYPE | ||
Type | JP10A-JP10F | JP11 |
AUI transceiver via DB-15 port | Open | Pins 1 & 2 closed |
Unshielded twisted pair | Closed | Pins 2 & 3 closed |
CABLE LENGTH SELECT | ||
Setting | JP13 | |
| » | 185 meters | Pins 1 & 2 closed |
305 meters | Pins 2 & 3 closed | |
Note: All cards on the network segment must have this function set the same. Link integrity must be enabled to select long cable length. | ||
FACTORY CONFIGURED SETTINGS | |
Jumper | Setting |
JP9 | Unused |
DIAGNOSTIC LED(S) | |||
LED | Color | Status | Condition |
LED1 | Yellow | Off | Normal operation |
LED1 | Yellow | On | A reversed twisted pair is detected and corrected |
LED2 | Green | On | Twisted pair network connection is good |
LED2 | Green | Off | Twisted pair network connection is broken |
My Books
