AN-500T/AN-202T/AN-808T/AN-202L Network Card Settings and Configuration
DANPEX CORPORATION
AN-500T/AN-202T/AN-808T/AN-202L
NIC Type | ARCnet |
Transfer Rate | 2.5Mbps |
Data Bus | 16-bit ISA |
Topology | Linear Bus Star |
Wiring Type | Unshielded twisted pair |
Boot ROM | Available |
BASE MEMORY ADDRESS SELECT | |||||
Address | SW1/7 | SW1/8 | SW1/9 | SW1/10 | |
| » | D0000h - D07FFh | Off | Off | On | Off |
C0000h - C07FFh | Off | Off | On | On | |
E0000h - E07FFh | Off | Off | Off | On | |
INTERRUPT SELECT | |||||||
IRQ | JP8 | JP9 | JP10 | JP11 | JP12 | JP13 | |
| » | IRQ9/2 | Open | Open | Open | Open | Open | Closed |
IRQ3 | Closed | Open | Open | Open | Open | Open | |
IRQ4 | Open | Closed | Open | Open | Open | Open | |
IRQ5 | Open | Open | Closed | Open | Open | Open | |
IRQ6 | Open | Open | Open | Closed | Open | Open | |
IRQ7 | Open | Open | Open | Open | Closed | Open | |
INTERRUPT SELECT (CONTINUED) | |||||
IRQ | JP3 | JP4 | JP5 | JP6 | JP7 |
IRQ14 | Closed | Open | Open | Open | Open |
IRQ15 | Open | Closed | Open | Open | Open |
IRQ12 | Open | Open | Closed | Open | Open |
IRQ11 | Open | Open | Open | Closed | Open |
IRQ10 | Open | Open | Open | Open | Closed |
I/O ADDRESS SELECT | |||||||
Address | SW1/1 | SW1/2 | SW1/3 | SW1/4 | SW1/5 | SW1/6 | |
| » | 2E0h | Off | On | Off | Off | Off | On |
2F0h | Off | On | Off | Off | Off | Off | |
300h | Off | Off | On | On | On | On | |
NODE ADDRESS | ||||||||
Node | SW2/1 | SW2/2 | SW2/3 | SW2/4 | SW2/5 | SW2/6 | SW2/7 | SW2/8 |
0 | - | - | - | - | - | - | - | - |
1 | On | On | On | On | On | On | On | Off |
2 | On | On | On | On | On | On | Off | On |
3 | On | On | On | On | On | On | Off | Off |
4 | On | On | On | On | On | Off | On | On |
251 | Off | Off | Off | Off | Off | On | Off | Off |
252 | Off | Off | Off | Off | Off | Off | On | On |
253 | Off | Off | Off | Off | Off | Off | On | Off |
254 | Off | Off | Off | Off | Off | Off | Off | On |
255 | Off | Off | Off | Off | Off | Off | Off | Off |
Note:Node address 0 is used for messaging between nodes and must not be used. A total of 255 node address settings are available. The switches are a binary representation of the decimal node addresses. Switch 8 is the Least Significant Bit and switch 1 is the Most Significant Bit. The switches have the following decimal values: switch 1=128, 2=64, 3=32, 4=16, 5=8, 6=4, 7=2, 8=1. Turn Off the switches and add the values of the Off switches to obtain the correct node address. (On=0, Off=1) | ||||||||
RESPONSE AND RECONFIGURATION TIMEOUTS | |||||
Reconfiguration Time | IDL Time ( m | Response Time ( m | JP1 | JP2 | |
| » | 840ms | 86 | 78 | Open | Open |
1.68 sec | 316 | 285 | Closed | Open | |
1.68 sec | 624 | 563 | Open | Closed | |
1.68 sec | 1237 | 1130 | Closed | Closed | |
TERMINATOR SELECT | |
Setting | JP14 |
Card used at end of Linear Bus | Closed |
Card not used at end of Linear Bus | Open |
DIAGNOSTIC LED | ||
Color | Status | Condition |
Green | On | PC is on |
Green | Blinking | Data is being transmitted/received |
FACTORY CONFIGURED SETTINGS | |
Jumper | Setting |
JP15 | Closed |
My Books
