ENET/U (Revision C2) Network Card Settings and Configuration
COMPEX, INC.
ENET/U (Revision C2)
NIC Type | Ethernet |
Transfer Rate | 10Mbps |
Data Bus | 8-bit ISA |
Topology | Linear bus |
Wiring Type | RG-58A/U 50ohm coaxial AUI transceiver via DB-15 port |
Boot ROM | Available |
CABLE TYPE | ||
Cable Type | J1A-G | |
| » | RG-58A/U 50ohm coaxial | Pins 2 & 3 closed |
AUI transceiver via DB-15 port | Pins 1 & 2 closed | |
SEGMENT LENGTH | ||
Maximum Length | J4 | |
| » | 185 meters | Closed |
300 meters | Open | |
Note:Segment length is the total length of cable between the two farthest cards on the segment. Each card on the segment must have this option set the same. | ||
NETWORK VERSION | ||
Version | J5 | |
| » | Ethernet version 2 | Open |
Ethernet version 1 | Closed | |
INTERRUPT REQUEST | ||||||
IRQ | J6A | J6B | J6C | J6D | J6E | |
2 | Closed | Open | Open | Open | Open | |
| » | 3 | Open | Closed | Open | Open | Open |
4 | Open | Open | Closed | Open | Open | |
| 5 | Open | Open | Open | Closed | Open | |
7 | Open | Open | Open | Open | Closed | |
WAIT STATE | ||
Setting | J7 | |
| » | Use preset 8-bit bus wait states | Open |
Use 2 wait states (6MHz or slower bus speed) | Closed | |
BOOT ROM | ||
Setting | J8 | |
| » | Disabled | Open |
Enabled | Closed | |
I/O BASE ADDRESS | ||||||
Address | J9A | J9B | J9C | J9D | ||
200h | Closed | Closed | Closed | Closed | ||
220h | Closed | Closed | Closed | Open | ||
240h | Closed | Closed | Open | Closed | ||
260h | Closed | Closed | Open | Open | ||
| » | 280h 1 | Closed | Open | Closed | Closed | |
2A0h | Closed | Open | Closed | Open | ||
2C0h | Closed | Open | Open | Closed | ||
2E0h | Closed | Open | Open | Open | ||
| » | 300h 2 | Open | Closed | Closed | Closed | |
320h | Open | Closed | Closed | Open | ||
340h | Open | Closed | Open | Closed | ||
360h | Open | Closed | Open | Open | ||
380h | Open | Open | Closed | Closed | ||
3A0h | Open | Open | Closed | Open | ||
3C0h | Open | Open | Open | Closed | ||
3E0h | Open | Open | Open | Open | ||
Note 1 :This setting is to be used when the card is in "WD MODE" (see below). Note 2 :This setting is to be used when the card is in "NE MODE" (see below). | ||||||
BOOT ROM ADDRESS | ||||||||
Address | J10A | J10B | J10C | J10D | J10E | J10F | ||
C0000 | Open | Closed | Closed | Closed | Closed | Closed | ||
C2000 | Open | Closed | Closed | Closed | Closed | Open | ||
C4000 | Open | Closed | Closed | Closed | Open | Closed | ||
C6000 | Open | Closed | Closed | Closed | Open | Open | ||
| » | C8000 2 | Open | Closed | Closed | Open | Closed | Closed | |
CA000 | Open | Closed | Closed | Open | Closed | Open | ||
CC000 | Open | Closed | Closed | Open | Open | Closed | ||
CE000 | Open | Closed | Closed | Open | Open | Open | ||
D0000 | Open | Closed | Open | Closed | Closed | Closed | ||
| » | D2000 1 | Open | Closed | Open | Closed | Closed | Open | |
D4000 | Open | Closed | Open | Closed | Open | Closed | ||
D6000 | Open | Closed | Open | Closed | Open | Open | ||
D8000 | Open | Closed | Open | Open | Closed | Closed | ||
DA000 | Open | Closed | Open | Open | Closed | Open | ||
DC000 | Open | Closed | Open | Open | Open | Closed | ||
DE000 | Open | Closed | Open | Open | Open | Open | ||
Note 1 :This setting is to be used when the card is in "WD MODE" (see below). Note 2 :This setting is to be used when the card is in "NE MODE" (see below). | ||||||||
NIC MODE | |
Mode | J11 |
"WD MODE" - running the ENETCPX, ED8003, or WDPLUS driver | Closed |
"NE MODE" - running the NOVELL NE1000 driver | Open |
I/O CHANNEL READY WAIT STATES | ||
Setting | J12 | |
| » | Use 4 wait states when #IOCHRDY active | Closed |
Use 2 wait states when #IOCHRDY active | Open | |
DATA BUS SIZE | ||
Setting | JP14 | |
| » | 16-bit | Closed |
8-bit | Open | |
DIAGNOSTIC LED(S) | ||
LED | Status | Condition |
LED1 | On | Data is being transmitted or received |
LED1 | Off | Data is not being transmitted or received |
My Books
