ANET-1-TP Network Card Settings and Configuration

COMPEX, INC.

ANET-1-TP

NIC Type
ARCnet
Transfer Rate
2.5Mbps
Data Bus
8-bit ISA
Topology
Linear Bus
Wiring Type
Shielded/Unshielded twisted pair
Boot ROM
Available

NODE ADDRESS
Node
SW1/1
SW1/2
SW1/3
SW1/4
SW1/5
SW1/6
SW1/7
SW1/8
0
-
-
-
-
-
-
-
-
1
Off
On
On
On
On
On
On
On
2
On
Off
On
On
On
On
On
On
3
Off
Off
On
On
On
On
On
On
4
On
On
Off
On
On
On
On
On
251
Off
Off
On
Off
Off
Off
Off
Off
252
On
On
Off
Off
Off
Off
Off
Off
253
Off
On
Off
Off
Off
Off
Off
Off
254
On
Off
Off
Off
Off
Off
Off
Off
255
Off
Off
Off
Off
Off
Off
Off
Off
Note:Node address 0 is used for messaging between nodes and must not be used.
A total of 255 node address settings are available. The switches are a binary representation of the decimal node addresses. Switch 1 is the Least Significant Bit and switch 8 is the Most Significant Bit. The switches have the following decimal values: switch 1=1, 2=2, 3=4, 4=8, 5=16, 6=32, 7=64, 8=128. Turn off the switches and add the values of the off switches to obtain the correct node address. (On=0, off=1)

DIAGNOSTIC LED(S)
LED
Color
Status
Condition
LED1
Red
On
Data is being transmitted
LED1
Red
Off
Data is not being transmitted
LED2
Green
On
Data is being received
LED2
Green
Off
Data is not being received

TIMEOUT CONFIGURATION
Response Time
JP1
JP2
»
74.7 m
Open
Open

283.4 m
Open
Closed

561.8 m
Closed
Open

1118.6 m
Closed
Closed
Note:Timeout is the time required for the network signal to make a complete trip around the network. Using a

MODE SELECTION
Mode
JP3
»
Normal
As shown in diagram on previous page

Special
As shown on diagram on previous page
Note:In normal mode, any 32KB memory segment in the system may be selected. For an AT, however, with

I/O BASE ADDRESS
Address
JP4
JP5
JP6
JP7
JP8
JP9

260h
Closed
Open
Open
Closed
Closed
Open

280h
Closed
Closed
Closed
Open
Closed
Open
»
2E0h
Closed
Open
Open
Open
Closed
Open

2F0h
Open
Open
Open
Open
Closed
Open

300h
Closed
Closed
Closed
Closed
Open
Open

360h
Closed
Open
Open
Closed
Open
Open
Note:Jumpers count from right to left in the diagram.

INTERRUPT REQUEST
IRQ
JP10
JP11
JP12
JP13
JP14
»
2
Closed
Open
Open
Open
Open

3
Open
Closed
Open
Open
Open

4
Open
Open
Closed
Open
Open

5
Open
Open
Open
Closed
Open

7
Open
Open
Open
Open
Closed

BOOT ROM ADDRESS
Address
JP15
JP16
JP17
JP18
JP19

C0000h
Closed
Closed
Closed
Open
Open

C8000h
Open
Closed
Closed
Open
Open

CC000h
Open
Open
Closed
Open
Open
»
D0000h
Closed
Open
Closed
Open
Open
Note:Jumpers count from the bottom up in the diagram.

Headaches Begone! A Systemic Approach To Healing Your Headaches

Don't Let Your Bike Seat Ruin Your Sex Life Book

ANET-1-TP Network Card Settings and Configuration

Search

My Books

Discover

NIC Type	ARCnet
Transfer Rate	2.5Mbps
Data Bus	8-bit ISA
Topology	Linear Bus
Wiring Type	Shielded/Unshielded twisted pair
Boot ROM	Available

NODE ADDRESS
Node	SW1/1	SW1/2	SW1/3	SW1/4	SW1/5	SW1/6	SW1/7	SW1/8
0	-	-	-	-	-	-	-	-
1	Off	On	On	On	On	On	On	On
2	On	Off	On	On	On	On	On	On
3	Off	Off	On	On	On	On	On	On
4	On	On	Off	On	On	On	On	On
251	Off	Off	On	Off	Off	Off	Off	Off
252	On	On	Off	Off	Off	Off	Off	Off
253	Off	On	Off	Off	Off	Off	Off	Off
254	On	Off	Off	Off	Off	Off	Off	Off
255	Off	Off	Off	Off	Off	Off	Off	Off
Note:Node address 0 is used for messaging between nodes and must not be used. A total of 255 node address settings are available. The switches are a binary representation of the decimal node addresses. Switch 1 is the Least Significant Bit and switch 8 is the Most Significant Bit. The switches have the following decimal values: switch 1=1, 2=2, 3=4, 4=8, 5=16, 6=32, 7=64, 8=128. Turn off the switches and add the values of the off switches to obtain the correct node address. (On=0, off=1)

DIAGNOSTIC LED(S)
LED	Color	Status	Condition
LED1	Red	On	Data is being transmitted
LED1	Red	Off	Data is not being transmitted
LED2	Green	On	Data is being received
LED2	Green	Off	Data is not being received

TIMEOUT CONFIGURATION
Response Time		JP1	JP2
»	74.7 m	Open	Open
	283.4 m	Open	Closed
	561.8 m	Closed	Open
	1118.6 m	Closed	Closed
Note:Timeout is the time required for the network signal to make a complete trip around the network. Using a

MODE SELECTION
Mode		JP3
»	Normal	As shown in diagram on previous page
	Special	As shown on diagram on previous page
Note:In normal mode, any 32KB memory segment in the system may be selected. For an AT, however, with

I/O BASE ADDRESS
Address		JP4	JP5	JP6	JP7	JP8	JP9
	260h	Closed	Open	Open	Closed	Closed	Open
	280h	Closed	Closed	Closed	Open	Closed	Open
»	2E0h	Closed	Open	Open	Open	Closed	Open
	2F0h	Open	Open	Open	Open	Closed	Open
	300h	Closed	Closed	Closed	Closed	Open	Open
	360h	Closed	Open	Open	Closed	Open	Open
Note:Jumpers count from right to left in the diagram.

INTERRUPT REQUEST
IRQ		JP10	JP11	JP12	JP13	JP14
»	2	Closed	Open	Open	Open	Open
	3	Open	Closed	Open	Open	Open
	4	Open	Open	Closed	Open	Open
	5	Open	Open	Open	Closed	Open
	7	Open	Open	Open	Open	Closed

BOOT ROM ADDRESS
Address		JP15	JP16	JP17	JP18	JP19
	C0000h	Closed	Closed	Closed	Open	Open
	C8000h	Open	Closed	Closed	Open	Open
	CC000h	Open	Open	Closed	Open	Open
»	D0000h	Closed	Open	Closed	Open	Open
Note:Jumpers count from the bottom up in the diagram.