CAPSERVER MODELS 325E, 425, 440E Motherboard Settings and Configuration
EVERGREEN SYSTEMS, INC.
CAPSERVER MODELS 325E, 425, 440E
Processor | AM386SX/CX486SLC/80386SX/TI486SXLC2 |
Processor Speed | 25/40MHz |
Chip Set | Unidentified |
Max. Onboard DRAM | 16MB |
Cache | None |
BIOS | Unidentified |
Dimensions | Unidentified |
I/O Options | 10-baseT Ethernet connector, floppy drive interface, IDE interface, parallel port, proprietary display connector, serial ports (2), thin Ethernet connector, VGA port |
NPU Options | 80387SX |
CONNECTIONS | |||
Purpose | Location | Purpose | Location |
Thin Ethernet connector | BNC | Speaker | J12 |
Proprietary display/CAPlink | DISP | External battery | J13 |
Floppy drive interface | FLP | Parallel port | PAR |
IDE interface | IDE | Serial port 1 (10-pin modular) | SER1 |
Keylock | J6 | Serial port 2 | SER2 |
Alternate keyboard | J7 | Ethernet 10BaseT connector | TBT |
Reset switch | J11 | VGA port | VGA |
USER CONFIGURABLE SETTINGS | |||
Function | Jumper | Position | |
» | Onboard VGA controller enabled | W1 | Closed |
Onboard VGA controller disabled | W1 | Open | |
» | VGA IRQ9 disabled | W2 | Open |
VGA IRQ9 enabled | W2 | Closed | |
» | Ethernet select 10BaseT | W3 | pins 1 & 2 closed |
Ethernet select thin | W3 | pins 2 & 3 closed | |
» | AT bus disabled (Capcard only receives DC from backplane) | W4 | Open |
AT bus enabled (Capcard may drive peripheral cards) | W4 | Closed | |
» | IDE interrupt select edge triggered | W5 | pins 1 & 2 closed |
IDE interrupt select level triggered | W5 | pins 2 & 3 closed | |
» | Floppy drive IRQ6 enabled | W6 | Closed |
Floppy drive IRQ6 disabled | W6 | Open | |
Note: Only one card in a segment can have W4 closed. Damage will result otherwise. See Below. | |||
DRAM CONFIGURATION TABLE | ||
Size | Bank 0 | Bank 1 |
2MB | (2) 1M x 9 | NONE |
4MB | (2) 1M x 9 | (2) 1M x 9 |
10MB | (2) 1M x 9 | (2) 4M x 9 |
16MB | (2) 4M x 9 | (2) 4M x 9 |
CAPCARD ID CONFIGURATION | |||||
ID# | SW1/1 | SW1/2 | SW1/3 | SW1/4 | SW1/5 |
1 | Off | Off | Off | Off | On |
2 | Off | Off | Off | On | Off |
3 | Off | Off | Off | On | On |
4 | Off | Off | On | Off | Off |
5 | Off | Off | On | Off | On |
6 | Off | Off | On | On | Off |
7 | Off | Off | On | On | On |
8 | Off | On | Off | Off | Off |
9 | Off | On | Off | Off | On |
10 | Off | On | Off | On | Off |
11 | Off | On | Off | On | On |
12 | Off | On | On | Off | Off |
13 | Off | On | On | Off | On |
14 | Off | On | On | On | Off |
15 | Off | On | On | On | On |
16 | On | Off | Off | Off | Off |
17 | On | Off | Off | Off | On |
18 | On | Off | Off | On | Off |
19 | On | Off | Off | On | On |
20 | On | Off | On | Off | Off |
21 | On | Off | On | Off | On |
22 | On | Off | On | On | Off |
23 | On | Off | On | On | On |
CAPCARD ID CONFIGURATION | |||||
ID# | SW1/1 | SW1/2 | SW1/3 | SW1/4 | SW1/5 |
24 | On | On | Off | Off | Off |
25 | On | On | Off | Off | On |
26 | On | On | Off | On | Off |
27 | On | On | Off | On | On |
28 | On | On | On | Off | Off |
29 | On | On | On | Off | On |
30 | On | On | On | On | Off |
Note: Capcard ID’s are necessary for the card to distinguish between cards. #1 is considered the server. | |||||
RESTORING FACTORY DEFAULTS | |||
Setting | SW1/6 | SW1/7 | SW1/8 |
Normal operation | Off | Off | Off |
Restore defaults boot from 1.44MB A: | On | Off | Off |
Restore defaults boot from 40MB C: | Off | On | Off |
Restore defaults boot from Novell network | Off | Off | On |
Suppress EEPROM overide and use CMOS | Off | On | On |
USER CONFIGURABLE SETTINGS | |||
Function | Jumper | Position | |
» | Interprocessor Communications Unit enabled | W7/IPCU DIS | Open |
Interprocessor Communications Unit disabled | W7/IPCU DIS | Closed | |
» | Onboard drive controllers enabled | W7/FDCIDE DIS | Open |
Onboard drive controllers disabled | W7/FDCIDE DIS | Closed | |
» | Factory configured - do not alter | W7/SCC SEL2 | Open |
» | Factory configured - do not alter | W7/SCC SEL1 | Open |
» | Factory configured - do not alter | W8/ all | Open |
» | Factory configured - do not alter | W9/ all | Open |
» | Factory configured - do not alter | W14/ all | Open |
PRIMARY SERIAL PORT CONFIGURATION | ||
Port address | W7/COM1 SEL1 | W7/COM1 SEL2 |
COM1 | Open | Open |
COM2 | Closed | Open |
COM3 | Open | Closed |
Disabled | Closed | Closed |
SECONDARY SERIAL PORT CONFIGURATION | ||
Port address | W7/COM2 SEL1 | W7/COM2 SEL2 |
COM1 | Open | Open |
COM2 | Closed | Open |
COM3 | Open | Closed |
Disabled | Closed | Closed |
PARALLEL PORT CONFIGURATION | ||
Port address | W7/PAR SEL1 | W7/PAR DIS |
LPT1 | Open | Open |
LPT2 | Closed | Open |
Disabled | Open | Closed |
ENET ADDRESS CONFIGURATION | |||
Address | W7/ENET SEL1 | W7/ENET SEL2 | W7/ENET DIS |
300h | Open | Open | Open |
320h | Closed | Open | Open |
340h | Open | Closed | Open |
360h | Closed | Closed | Open |
Disabled | Open | Open | Closed |
ENET INTERRUPT CONFIGURATION | ||||
Interrupt | W10/IRQ3 | W10/IRQ4 | W10/IRQ5 | W10/IRQ9 |
IRQ3 | Closed | Open | Open | Open |
IRQ4 | Open | Closed | Open | Open |
IRQ5 | Open | Open | Closed | Open |
IRQ9 | Open | Open | Open | Closed |
PARALLEL PORT INTERRUPT CONFIGURATION | ||
Interrupt | W11/IRQ5 | W11/IRQ7 |
IRQ5 | Closed | Open |
IRQ7 | Open | Closed |
Disabled | Open | Open |
SERIAL PORT INTERRUPT CONFIGURATION | ||
Port | W12/IRQ3 | W12/ IRQ4 |
COM1 | pins COM1 & IRQ3 closed | pins COM1 & IRQ4 closed |
COM2 | pins COM2 & IRQ3 closed | pins COM2 & IRQ3 closed |
Note: Names represent pins in diagram. The diagram shows COM1 at IRQ4 and COM2 at IRQ3. | ||
IPCU INTERRUPT CONFIGURATION | ||||
Interrupt | W13/IRQ7 | W13/IRQ11 | W13/IRQ12 | W13/IRQ15 |
IRQ7 | Closed | Open | Open | Open |
IRQ11 | Open | Closed | Open | Open |
IRQ12 | Open | Open | Closed | Open |
IRQ15 | Open | Open | Open | Closed |
WARNING |
ONLY ONE CARD IN A GIVEN SEGMENT OF THE ABOVE BACKPLANES MAY HAVE ITS AT BUS JUMPER INSTALLED AT W4. IF MORE THEN ONE CARD HAS W4 INSTALLED DAMAGE WILL OCCUR. |
TERMINATING RESISTOR CONFIGURATION | |
Setting | R100 |
First and last CAPcards in CAPserver | Installed |
All other cards in CAPserver | Not installed |
My Books
