ZOLTRIX, INC.
FM-288I
Card Type | Modem, Fax |
Chip Set | Rockwell |
I/O Options | Line in (RJ-11), line out (RJ-11) |
Maximum Modem Rate | 28.8Kbps |
Maximum Fax Rate | 14.4Kbps |
Data Modulation Protocol | Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.32, V.32bis, V.34 Rockwell V.FC |
Fax Modulation Protocol | ITU-T V.17, V.21 CH.2, V.27ter, V.29 |
Error Correction/Compression | MNP5, V.42, V.42bis |
Fax Class | Class I & II |
Data Bus | 8-bit ISA |
Card Size | Half-length, full-height card |
CONNECTIONS | ||||||
Function | Label | Function | Label | |||
Line out | CN1 | Line in | CN2 |
SERIAL PORT ADDRESS | ||
Setting | SW1/5 | SW1/6 |
COM1 (3F8h) | On | On |
í COM2 (2F8h) | Off | On |
COM3 (3E8h) | On | Off |
COM4 (2E8h) | Off | Off |
INTERRUPT SETTINGS | |||||
IRQ | SW1/1 | SW1/2 | SW1/3 | SW1/4 | SW1/7 |
IRQ2 | Off | Off | Off | Off | On |
í IRQ3 | Off | Off | Off | On | Off |
IRQ4 | Off | Off | On | Off | Off |
IRQ5 | Off | On | Off | Off | Off |
IRQ7 | On | Off | Off | Off | Off |
SUPPORTED COMMAND SET |
Basic AT Commands |
AT, ‘+++’, A/ |
A, B, C, D, E, F, H, I, L, M, N, O, P, Q, T, V, W, X, Y, Z |
&C, &D, &F, &G, &J, &K, &L, &M, &P, &Q, &R, &S, &T, &V, &W, &X, &Y, &Z |
Extended AT Commands |
\A, \B, \G, \K, \L, \N |
%C, %E, %L, %Q |
S Registers |
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S25, S26, |
S27, S29, S30, S32, S33, S36, S37, S38, S40, S41, S46, S48, S82, S86, S95 |
Special Commands |
+MS |
Note: See MHI Help File for full command documentation. |
Proprietary AT Command Set
DIAL | |
Type: | Immediate |
Format: | AT [cmds] D<#> [cmds] |
Description: | Dials telephone number according to any modifiers included in the string |
Note: | Any combination of modifiers can be used to produce the desired dial functions in sequence. |
Command | Function |
DP | Pulse dialing enabled |
í DT | Tone dialing enabled |
DW | Dialing resumed following dial tone detection |
D, | Dialing paused for amount of time specified in S8 register |
D/ | Set dialing delay for 0.125 seconds |
D! | Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. |
D@ | Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. |
D; | Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. |
D^ | Dialing paused for 5 seconds |
DR | Reverse mode enabled. Modem uses Answer mode frequencies to modem set to Originate Only mode. |