WISECOM, INC.
WS-2814EM4
Card Type | Modem (synchronous/asynchronous) |
Chipset | AT & T |
Maximum Data Rate | 28.8Kbps |
Maximum Fax Rate | 14.4Kbps |
Data Bus | Serial |
Fax Class | Class I & II |
Data Modulation | Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 AT&T V.32terbo |
Fax Modulation | ITU-T V.17, V.21CH2, V.27ter, V.29 |
Error Correction/Compression | MNP5, V.42, V.42bis |
CONNECTIONS | |||
Function | Label | Function | Label |
Line in | CN1 | RS-232/422 | CN3 |
Line out | CN2 | DC power in | CN4 |
DIAGNOSTIC LED(S) | |||
LED | Color | Status | Condition |
MR | Red | On | Power is on |
MR | Red | Off | Power is off |
TR | Red | On | DTR signal is high |
TR | Red | Off | DTR signal is low |
SD | Red | On | Modem is transmitting data |
SD | Red | Off | Modem is not transmitting data |
RD | Red | On | Modem is receiving data |
RD | Red | Off | Modem is not receiving data |
OH | Red | On | Modem is off-hook |
OH | Red | Off | Modem is on-hook |
CD | Red | On | Carrier signal detected |
CD | Red | Off | Carrier signal not detected |
DIAGNOSTIC LED(S) (CON’T) | |||
LED | Color | Status | Condition |
AA | Red | On | Auto-answer enabled |
AA | Red | Off | Auto-answer disabled |
EC | Red | On | Error correction enabled |
EC | Red | Off | Error correction disabled |
SUPPORTED STANDARD COMMANDS |
Basic AT Commands |
+++, ‘comma’, A/ |
A, E, H, L, M, N, O, P, Q, T, V, X, Y, Z |
&C, &D, &F, &G, &K, &L, &M, &P, &Q, &R, &S, &T, &V, &W, &X, &Y, &Z |
Extended AT Commands |
\A, \B, \C, \G, \J, \K, \N, \Q, \T, \X |
%A, %B, %C, %D, %E, %N, %Q |
S-Registers |
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S25, S26 |
S27, S30, S91 |
Note: See MHI documentation for complete information. |
UNIDENTIFIED COMMANDS | |
Command | Default |
S15 | 83 |
S17 | 75 |
S19 | 3 |
S20 | 0 |
S24 | 72 |
S28 | 16 |
Proprietary AT Command Set
DIAL | |
Type: | Immediate |
Format: | AT [cmds] D<#>;[cmds] |
Description: | Dials the telephone number indicated according to any modifiers included in the string. |
Note: | Any combination of modifiers can be used to produce the desired dial functions in sequence. |
Command | Function |
DL | Re-dial last number. |
DP | Pulse dialing enabled. |
DR | Answer mode enabled; originate mode disabled following handshake initiation. |
DS=n | Dial stored telephone number n. |
DT | Tone dialing enabled. |
DW | Dialing resumed following dial tone detection. |
D, | Dialing paused for amount of time specified in S8 register. |
D! | Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. |
D@ | Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. |
D^ | Calling tone enabled for this call. |
D; | Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. |
V.32terbo AND V.34 PROTOCOLS | |
Type: | Configuration |
Format: | AT [cmds] \Mn [cmds] |
Description: | Selects whether the modem will use V.32terbo and V.34 modulation protocols. |
Command | Protocol |
í \M0 | V.32terbo and V.34 protocols enabled. |
\M1 | V.32terbo protocol disabled. |
\M2 | V.34 protocol disabled. |
See WISECOM, INC. WS-1414IM4 for a full command summary.