WISECOM, INC.
WS-5614JS3/ES3 (INTERNAL)
Card Type | Modem |
Chip Set | Unidentified |
I/O Options | Line out, line in, speaker out, microphone in |
Maximum Modem Rate | 56Kbps |
Maximum Fax Rate | 14.4Kbps |
Data Modulation Protocol | Bell 103/212A ITU-T V.22, V.22bis, V.32, V.32bis, V.34, 56Kflex |
Fax Modulation Protocol | ITU-T V.17, V.21 CH.2, V.27ter, V.29 |
Error Correction/Compression | MNP5, V.42, V.42bis |
Fax Class | Class I |
Data Bus | 8-bit ISA |
CONNECTIONS | ||||||
Function | Label | Function | Label | |||
Line out (RJ-11) | CN1 | Speaker out | CN3 | |||
Line in (RJ-11) | CN2 | Microphone in | CN4 |
PLUG & PLAY | ||
Setting | JP3 | JP4 |
? Plug & play enabled | Pins 1 & 2 closed | Pins 1 & 2 closed |
Plug & play disabled | Pins 2 & 3 closed | Pins 2 & 3 closed |
SERIAL PORT ADDRESS | ||
Setting | SW1/1 | SW1/2 |
COM1 (3F8h) | On | On |
COM2 (2F8h) | Off | On |
COM3 (3E8h) | On | Off |
COM4 (2E8h) | Off | Off |
INTERRUPT | ||||
IRQ | SW1/3 | SW1/4 | SW1/5 | SW1/6 |
2 | On | Off | Off | Off |
3 | Off | On | Off | Off |
4 | Off | Off | On | Off |
5 | Off | Off | Off | On |
SUPPORTED COMMAND SET |
Basic AT Commands |
AT, ‘+++’, A/ |
A, B, E, H, V |
&C, &M, &P, &T, &V, &W, &X, &Y, &Z |
Extended AT Commands |
%C, %E, %L, %Q |
\A, \B, \K, \N |
Special Commands |
S Registers |
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9,S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25 |
S26, S27, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S46, S48, S82, S91, S92, S95 |
Note: See MHI Help File for full command documentation. |
PROPRIETARY AT COMMAND SET
COMMUNICATIONS MODE | |
Type: | Configuration |
Format: | AT [cmds] &Qn [cmds] |
Description: | Selects communications mode options |
Command | Mode |
&Q0 | Asynchronous mode, serial port speed follows connect speed. |
&Q1 | Asynchronous off-line command mode and synchronous connect mode. |
&Q2 | Asynchronous off-line command mode - modem autodials first number in directory, then synchronous connect mode. |
&Q3 | Asynchronous off-line command mode on low DTR, synchronous connect mode on high DTR. |
? &Q5 | Error correction mode |
&Q6 | Buffered asynchronous mode |
DATA SET READY (DSR) | |
Type: | Configuration |
Format: | AT [cmds] &Sn [cmds] |
Description: | Selects DSR options |
Command | Function |
&S0 | DSR forced high |
&S1 | DSR high only while modem is handshaking or connected |
DATA TERMINAL READY (DTR) | ||
Type: | Configuration | |
Format: | AT [cmds] &Dn [cmds] | |
Description: | Selects modem response to DTR | |
Command | Mode | |
&D0 | DTR ignored | |
&D1 | DTR toggle causes online command mode | |
? &D2 | DTR toggle causes modem to go on-hook | |
&D3 | Modem reset on DTR toggle |
DIAL | |
Type: | Immediate |
Format: | AT [cmds] D<#> [cmds] |
Description: | Dials telephone number according to any modifiers included in the string |
FACTORY DEFAULT PROFILE | |
Type: | Configuration |
Format: | AT [cmds] &F [cmds] |
Description: | Sets values in active profile to values found in the default profile |
&F0 | Load factory configuration 0 |
&F1 | Load factory configuration 1 |
FLOW CONTROL | |
Type: | Configuration |
Format: | AT [cmds] &Kn [cmds] |
Description: | Enables flow control options |
Command | Function |
&K0 | Flow control disabled |
&K3 | RTS/CTS flow control enabled |
&K4 | XON/XOFF flow control enabled |
&K5 | Transparent XON/XOFF flow control enabled |
? &K6 | Both RTS/CTS & XON/XOFF flow control enabled |
GUARD TONE | |
Type: | Configuration |
Format: | AT [cmds] &Gn [cmds] |
Description: | Commands the modem to transmit a guard tone in V.22/V.22bis |
Note: Used primarily for international data transmission | |
Command | Function |
? &G0 | Guard tone disabled |
&G1 | 550Hz guard tone enabled |
&G2 | 1800Hz guard tone enabled |
REPORT INFORMATION | |
Type: | Immediate |
Format: | AT [cmds] In [cmds] |
Description: | Displays information requested |
Command | Function |
I0 | Reports modem model and speed |
I1 | Reports ROM checksum |
I2 | Tests and reports ROM checksum |
I3 | Reports product ID string |
I6 | Reports diagnostic information |
I7 | Reports product configuration |
RESTORE PROFILE ON POWER-UP | |
Type: | Configuration |
Format: | AT [cmds] Yn [cmds] |
Description: | Restores a selected profile to default profile on power-up (hard reset) |
Command | Function |
? Y0 | Restore stored profile 0 on power-up |
Y1 | Restore stored profile 1 on power-up |
Y2 | Load factory default configuration 0 on power-up |
Y3 | Load factory default configuration 1 on power-up |
Y4 | Load factory default configuration 2 on power-up |
RTS/CTS | |
Type: | Configuration |
Format: | AT [cmds] &Rn [cmds] |
Description: | Selects RTS/CTS options |
Command | Function |
&R0 | CTS follows RTS in data mode; RTS is ignored in command mode. |
? &R1 | CTS forced high, RTS is ignored. |
SOFT RESET | |
Type: | Configuration |
Format: | AT [cmds] Zn [cmds] |
Description: | Restores modem profiles previously stored in non-volatile RAM using the &W command |
Command | Function |
? Z1 | Restore stored profile 0 |
Z2 | Restore stored profile 1 |
Z3 | Load factory default configuration 0 |
Z4 | Load factory default configuration 1 |
Z5 | Load factory default configuration 2 |
SPEAKER MODE | |
Type: | Configuration |
Format: | AT [cmds] Mn [cmds] |
Description: | Selects various speaker options |
Command | Function |
M0 | Speaker disabled |
M1 | Speaker enabled until carrier signal detected |
SPEAKER VOLUME | |
Type: | Configuration |
Format: | AT [cmds] Ln [cmds] |
Description: | Controls speaker volume |
Command | Function |
L0 | Low volume setting |
L1 | Low volume setting |
? L2 | Medium volume setting |
L3 | Highest volume setting |
EXTENDED AT COMMAND SET
MODULATION SELECTION | |
Type: | Configuration |
Format: | AT [cmds] +MS=x,y,z,a,b,c [cmds] |
Description: | Sets options for active protocol; the transfer rates specified by z and a must be valid for the protocol selected. |
Command | Function |
x=0 | V.21 |
x=1 | V.22 |
x=2 | V.22bis |
x=3 | V.23 |
x=9 | V.32 |
x =10 | V.32bis |
x=11 | V.34, K56flex |
x =64 | Bell 103 |
x =69 | Bell 212A |
y =0 | Automode disabled |
y =1 | Auto-detect highest speed enabled |
z, a=300 | Set minimum or maximum transfer rate at 300bps, respectively. |
z, a =1200 | Set minimum or maximum transfer rate at 1200bps, respectively. |
z, a =2400 | Set minimum or maximum transfer rate at 2400bps, respectively. |
z, a =4800 | Set minimum or maximum transfer rate at 4800bps, respectively. |
z, a =7200 | Set minimum or maximum transfer rate at 7200bps, respectively. |
z, a =9600 | Set minimum or maximum transfer rate at 9600bps, respectively. |
z, a =12000 | Set minimum or maximum transfer rate at 12000bps, respectively. |
z, a =14400 | Set minimum or maximum transfer rate at 14400bps, respectively. |
z, a =16800 | Set minimum or maximum transfer rate at 16800bps, respectively. |
z, a =19200 | Set minimum or maximum transfer rate at 19200bps, respectively. |
z, a =21600 | Set minimum or maximum transfer rate at 21600bps, respectively. |
z, a =24000 | Set minimum or maximum transfer rate at 24000bps, respectively. |
z, a =26400 | Set minimum or maximum transfer rate at 26400bps, respectively. |
z, a =28800 | Set minimum or maximum transfer rate at 28800bps, respectively. |
z, a =33600 | Set minimum or maximum transfer rate at 33600bps, respectively. |
b =0 | m -law encoding |
b= 1 | A -law encoding |
c =0 | Robbed bit signaling disabled |
c=1 | Robbed bit signaling enabled |
S(Status) REGISTERS
CONNECTION FAILURE CODES | |
Type: | Register |
Format | AT [cmds] S86? [cmds] |
Description: | Reports codes which correspond to the possible causes of a connection failure |
Value | Meaning |
0 | Normal hang up |
4 | Carrier signal lost |
5 | No error-control detected for remote modem during feature negotiation |
9 | No common protocol found |
12 | No failure - remote modem disconnected normally |
13 | Remote modem failed to respond after 10 re-transmissions same message |
14 | Violation of negotiated protocol caused failure |