DATA/FAX/VOICE MODEM 14.4 (REV.1) modem/telephone/ISDN Settings and Configuration

Card Type	Fax, Modem (asynchronous), Voice
Chip Set	Cirrus Logic
I/O options	Voice
Maximum Data Rate	14.4Kbps
Maximum Fax Rate	14.4Kbps
Data Bus	8-bit ISA
Fax Class	Class I
Data Modulation Protocol	Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.32, V.32bis
Fax Modulation Protocol	ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression	MNP5, V.42, V.42bis

CONNECTIONS
Function	Label		Function		Label
Line in		CN1		Line out		CN2

SERIAL PORT ADDRESS
Setting	JP8/1	JP8/2
COM1 (3F8h)	Pins 1 & 2 closed	Pins 1 & 2 closed
COM2 (2F8h)	Pins 2 & 3 closed	Pins 1 & 2 closed
COM3 (3E8h)	Pins 1 & 2 closed	Pins 2 & 3 closed
í COM4 (2E8h)	Pins 2 & 3 closed	Pins 2 & 3 closed

INTERRUPT
Setting	JP8/3	JP8/4	JP8/5	JP8/6
2	Closed	Open	Open	Open
í 3	Open	Closed	Open	Open
4	Open	Open	Closed	Open
5	Open	Open	Open	Closed

ACCEPT RELIABLE MODE
Type:	Immediate
Format:	AT [cmds] \U [cmds]
Description:	Accepts remote modem’s request for reliable link

AUTO FALL FORWARD/FALLBACK
Type:	Configuration
Format:	AT [cmds] %Gn [cmds]
Description:	Selects auto fallback/fall forward
Command	Function
í %G0	Fallback/fall forward enabled
%G1	Fallback/fall forward disabled

AUTO-RELIABLE FALLBACK CHARACTER
Type:	Configuration
Format:	AT [cmds] %An [cmds]
Default:	Unidentified
Range:	0-127
Unit:	ASCII
Description:	Sets the character used as the auto-reliable fallback character. %A0 will disable this function.

AUTO-RELIABLE TIME BUFFER CONFIGURATION
Type:	Configuration
Format:	AT [cmds] \Cn [cmds]
Description:	Controls the handling of incoming data during auto-reliable time period
Command	Function
í \C0	Data is discarded
\C1	Data is buffered
\C2	Data is discarded, modem returns to normal mode on receiving auto-reliable fallback character.

AUTO-RETRAIN
Type:	Configuration
Format:	AT [cmds] %En [cmds]
Description:	Selects auto-retrain mode
Command	Function
%E0	Auto-retrain disabled
í %E1	Auto-retrain enabled

BIT MAPPED REGISTERS
Register	Default
S14	Unidentified
S21	Unidentified
S22	Unidentified
S23	Unidentified
S27	Unidentified

BREAK SEND
Type:	Configuration
Format:	AT [cmds] \Bn [cmds]
Range:	0-9
Unit:	.1 seconds
Description:	Sends break to modem

BREAK TYPE
Type	Configuration
Format	AT [cmds] \Kn [cmds]
Default	5
Range	0-5
Description	Configures action of break signal

CALLING TONE
Type:	Configuration
Format:	AT [cmds] -Cn [cmds]
Description:	Controls whether the DTE will allow the modem to send a 1300Hz calling tone when originating.
Command	Function
í -C0	Disable calling tone
-C1	Enable calling tone

COMPRESSION
Type:	Configuration
Format:	AT [cmds] %Cn [cmds]
Description:	Selects data compression
Command	Function
%C0	Data compression disabled
í %C1	MNP5 enabled

CONNECT MODE
Type:	Configuration
Format:	AT [cmds] \Nn [cmds]
Description:	Sets connect mode
Command	Function
\N0	Normal mode enabled
\N1	Direct mode enabled
\N2	MNP mode enabled
í \N3	Auto-reliable mode enabled
\N4	V.42 mode enabled

CONVERT TO RELIABLE MODE
Type:	Immediate
Format:	AT [cmds] \Y [cmds]
Description:	Initiates reliable mode link

EXTENDED RESULT CODES
Type:	Configuration
Format:	AT [cmds] \Vn [cmds]
Description:	Selects extended result codes
Command	Function
\V0	Extended result codes disabled
\V1	Reliable result codes enabled
í \V2	Error control and compression result codes enabled

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] \Gn [cmds]
Description:	Selects modem port flow control
Command	Function
í \G0	Flow control disabled
\G1	Flow control enabled

FLOW CONTROL TYPE
Type:	Configuration
Format:	AT [cmds] \Qn [cmds]
Description:	Sets type of flow control used by modem
Command	Function
\Q0	Flow control disabled
\Q1	XON/XOFF flow control enabled
\Q2	CTS flow control to DTE enabled
í \Q3	RTS/CTS flow control enabled

INACTIVITY TIMER
Type:	Configuration
Format:	AT [cmds] \Tn [cmds]
Default:	0
Range:	0-90
Unit:	1 minute
Description:	Sets the length of time that the modem does not receive information before it disconnects.

INACTIVITY TIMER
Type:	Register
Format:	AT [cmds] S90=n [cmds]
Default:	0
Range:	0-255
Unit:	1 second
Description:	Sets the length of time that the modem does not receive information before it disconnects. S90=0 will disable.

LOCK SERIAL PORT
Type:	Configuration
Format:	AT [cmds] \Jn [cmds]
Description:	Sets operation of serial port speed
Command	Function
í \J0	Serial speed locked
\J1	Serial speed follows connect speed

MAXIMUM BLOCK SIZE FOR TRANSMISSION
Type:	Configuration
Format:	AT [cmds] \An [cmds]
Description:	Sets the maximum transmittable block size
Command	Function
\A0	MNP block size is 64 characters
\A1	MNP block size is 128 characters
\A2	MNP block size is 192 characters
í \A3	MNP block size is 256 characters

ON-LINE IN RELIABLE MODE
Type:	Immediate
Format:	AT [cmds] \O [cmds]
Description:	Returns to on-line and requests reliable mode connection.

RETURN TO RELIABLE MODE
Type:	Immediate
Format:	AT [cmds] \Z [cmds]
Description:	Ends reliable mode link and initiate return to normal mode

TEST MODES
Format		AT [cmds] S16=n [cmds]
Default:		Unidentified
Range:		Unidentified
Unit:		Bit-mapped
Description:		Controls loopback tests, analog, digital, remote digital, and self tests.
Bit	Value	Function
0	0 1	Local analog loopback not in progress Local analog loopback in progress
1	0	Not used
2	0 1	Local digital loopback not in progress Local digital loopback in progress
3	0 1	Modem not in remote digital loopback Remote digital loopback in progress
4	0 1	Remote digital loopback not requested Remote digital loopback requested
5	0 1	Remote digital loopback w/ self-test not in progress Remote digital loopback w/ self-test in progress
6	0 1	Local analog loopback w/ self-test not in progress Local analog loopback w/ self-test in progress

V.42 DETECTION PHASE
Type:	Configuration
Format:	AT [cmds] -Jn [cmds]
Description:	Controls V.42 detection
Command	Function
-J0	V.42 detection disabled
í -J1	V.42 detection enabled

V.42bis COMPRESSION CONTROL
Type:	Configuration
Format:	AT [cmds] "Hn [cmds]
Description:	Controls V.42bis data compression
Command	Function
"H0	V.42bis disabled
"H1	V.42bis when transmitting enabled
"H2	V.42bis when receiving enabled
í "H3	V.42bis when transmitting/receiving enabled

V.42bis MAXIMUM STRING LENGTH
Type:	Immediate
Format:	AT [cmds] "Closed [cmds]
Default:	16
Range:	6-250
Unit:	Characters
Description:	Selects string size for V.42bis compression

XON/XOFF PASS-THROUGH
Type:	Configuration
Format:	AT [cmds] \Xn [cmds]
Description:	Selects whether XON/XOFF signals are sent to remote modem
Command	Function
í \X0	XON/XOFF signals trapped by local modem
\X1	XON/XOFF passed through local modem