WESTECH KOREA, INC.
ROCKWELL K56FLEX
Card Type | Modem |
Chip Set | Rockwell |
Maximum Modem Rate | 56Kbps |
Maximum Fax Rate | 14.4Kbps |
Data Modulation Protocol | Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32ter, V.32bis, V.34, V.90 |
Fax Modulation Protocol | ITU-T V.17, V.21 CH2, V.27ter, V.29, V.33 |
Error Correction/Compression | MNP5, V.42, V.42bis |
Fax Class | I & II |
Data Bus | PCMCIA |
WESTECH-KOREA-INC-Modem-ROCKWELL-K56FLEX
SUPPORTED COMMAND SET | |
Basic AT Commands | |
AT, A/ | |
A, B, D, E, H, M, O, P, Q, T, V, W, X, Y, Z | |
&C, &M, &P, &Q, &R, &T, &W, &X, &Y, &Z | |
Extended AT Commands | |
\A, \B, \K, \N, \V | |
%C, %E, %L, %Q | |
Special Commands | |
+MS, -K, #CID | |
S Registers | |
S0, S1, S2, S3, S4, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S22, S23, S24, S25, S26, S27 | |
S28, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92, S95 | |
Note: | See MHI Help File for full command documentation. Specific S-register information unavailable; S-registers may vary slightly from MHI help file. |
PROPRIETARY AT COMMAND SET
AUTO-MODE DETECTION | |
Type: | Configuration |
Format: | AT [cmds] Nn [cmds] |
Description: | Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. |
Command | Function |
N0 | Auto-mode detection disabled. Handshake begins at line speed designated by the S37 register. If S37=0 handshake follows interface speed |
N1 | Auto-mode detection enabled. Handshake begins at line speed designated by the S37 register. If S37=0 handshake at highest possible speed with fallback to lower speed if necessary |
COMMUNICATION PROTOCOLS | |
Type: | Configuration |
Format: | AT [cmds] Fn [cmds] |
Description: | Selects the communication protocol for data calls |
Command | Protocol |
F0 | Auto-mode detection enabled |
F1 | V.21 or Bell 103 |
F2 | Reserved |
F3 | V.23 |
F4 | V.22 or Bell 212/A at 1200bps |
F5 | V.22bis |
F6 | V.32 or V.32bis at 4800bps |
F7 | V.32bis at 7200bps |
F8 | V.32 or V.32bis at 9600bps |
F9 | V.32bis at 12.0Kbps |
F10 | V.32bis at 14.4Kbps |
CONFIGURATION PROFILES | |
Type: | Immediate |
Format: | AT [cmds] &V [cmds] |
Description: | Displays active and stored configuration profiles |
Command | Function |
&V0 | Display current configurations |
&V1 | Display connection statistics |
DATA SET READY (DSR) | |
Type: | Configuration |
Format: | AT [cmds] &Sn [cmds] |
Description: | Selects DSR options |
Command | Function |
&S0 | DSR forced high |
&S1 | DSR high only while modem is handshaking or connected |
DATA TERMINAL READY (DTR) | |||||
Type: | Configuration | ||||
Format: | AT [cmds] &Dn [cmds] | ||||
Description: | Selects modem response to DTR | ||||
Note: The action each variant of &D causes depends on the setting of &Q | |||||
&Q Setting | &D0 | &D1 | &D2 | &D3 | |
&Q0, &Q5, &Q6 | Command 0 | Command 1 | Command 2 | Command 4 | |
&Q1, &Q4 | Command 2 | Command 1 | Command 2 | Command 4 | |
&Q2, &3 | Command 2 | Command 2 | Command 2 | Command 2 | |
Command | Function | ||||
Command 0 | Modem does not respond to DTR | ||||
Command 1 | Modem goes to command mode after DTR goes is off | ||||
Command 2 | Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. | ||||
Command 3 | Modem is initialized after DTR goes off |
FACTORY DEFAULT PROFILE | |
Type: | Configuration |
Format: | AT [cmds] &F [cmds] |
Description: | Sets values in active profile to values found in the default profile |
Command | Function |
&F0 | Load factory configuration 0 |
&F1 | Load factory configuration 1 |
FLOW CONTROL | |
Type: | Configuration |
Format: | AT [cmds] &Kn [cmds] |
Description: | Enables flow control options |
Command | Function |
&K0 | Flow control disabled |
&K3 | RTS/CTS flow control enabled |
&K4 | XON/XOFF flow control enabled |
&K5 | Transparent XON/XOFF flow control enabled |
&K6 | Unidirectional XON/XOFF flow control enabled |
GUARD TONE | |
Type: | Configuration |
Format: | AT [cmds] &Gn [cmds] |
Description: | Commands the modem to transmit a guard tone in V.22/V.22bis |
Command | Function |
&G0 | Guard tone disabled |
&G1 | Guard tone disabled |
&G2 | 1800Hz guard tone enabled |
JACK TYPE | |
Type: | Configuration |
Format: | AT [cmds] &Jn [cmds] |
Description: | For purposes compatibility only. Performs no function |
LINE TYPE | |
Type: | Configuration |
Format: | AT [cmds] &Ln [cmds] |
Description: | Selects line type |
Command | Line Type |
&L0 | Switched line (PSTN/Dial-up) |
REPORT INFORMATION | |
Type: | Immediate |
Format: | AT [cmds] In [cmds] |
Description: | Displays information requested |
Command | Function |
I0 | Reports product code |
I1 | Reports ROM checksum |
I2 | Tests and reports ROM checksum |
I3 | Reports firmware version and application codes |
I4 | Reports OEM identifier string in either binary or ASCII format |
I5 | Reports country code |
I6 | Reports data pump model and internal code |
I7 | Reports DAA code |
SPEAKER VOLUME | |
Type: | Configuration |
Format: | AT [cmds] Ln [cmds] |
Description: | Controls speaker volume |
Command | Function |
L0 | Low volume setting |
L1 | Low volume setting |
L2 | Medium volume setting |
L3 | Highest volume setting |
TRANSMIT CARRIER | |
Type: | Configuration |
Format: | AT [cmds] Cn [cmds] |
Description: | Command non-functional; for compatibility only. Returns OK |
SPECIAL COMMANDS
BLACKLIST | |
Type: | Immidiate |
Format: | AT [cmds] *B [cmds] |
Description: | Displays blacklisted numbers. If no numbers are blacklisted, returns OK. |
COUNTRY SELECT | |
Type: | Configuration |
Format: | AT [cmds] *NCn [cmds] |
Range: | 1 - 8 |
Description: | Selects country code from NVRAM |
DELAY | |
Type: | Immidiate |
Format: | AT [cmds] *D [cmds] |
Description: | Displays delayed numbers with the delay associated with each. If no numbers are delayed, returns OK. |
DISTINCTIVE RING | |
Type: | Immediate |
Format: | AT [cmds] -SDR=n [cmds] |
Description: | Selects the distinctive ring settings |
Command | Function |
-SDR=0 | Distinctive ring disabled |
-SDR=1 | Type 1 enabled |
-SDR=2 | Type 2 enabled |
-SDR=3 | Type 1 and 2 enabled |
-SDR=4 | Type 3 enabled |
-SDR=5 | Type 1 and 3 enabled |
-SDR=6 | Type 2 and 3 enabled |
-SDR=7 | Type 1, 2, and 3 enabled |
FLASH MEMORY | |
Type: | Configuration |
Format: | AT [cmds] **n [cmds] |
Description: | Controls download to flash memory |
Command | Function |
**0 | Downloads into flash memory at last sensed speed |
**1 | Downloads into flash memory at 38.4Kbps |
**2 | Downloads into flash memory at 57.6Kbps |
MNP10 - POWER LEVEL ADJUST | |
Type: | Configuration |
Format: | AT [cmds] -SEC=n [cmds] |
Range: | 0-30 |
Unit: | -1dBm |
Description: | Controls automatic transmit power level adjustment during MNP 10 link negotiation |
Command | Function |
-SEC=0 | MNP10 disabled. Transmission level is set in the S91 register |
-SEC=1, [tx_lev] | MNP10 enabled. Set transmit level |
PLUG & PLAY SERIAL NUMBER | |
Type: | Immediate |
Format: | AT [cmds] %7n [cmds] |
Range: | 8 |
Unit: | Hexidecimal |
Description: | Sets and stores numbers for serial plug & play |
PLUG & PLAY VENDOR ID & PRODUCT NUMBER | |
Type: | Immediate |
Format: | AT [cmds] %8n [cmds] |
Range: | 3 (ASCII), 4 (hex) |
Unit: | ASCII, Hexidecimal |
Description: | Sets and stores numbers for serial plug & play |
RPI/VIDEO READY MODE | |
Type: | Configuration |
Format: | AT [cmds] +Hn [cmds] |
Description: | Enables/disables RPI & video ready mode |
Command | Function |
+H0 | RPI/video ready mode disabled |
+H1 | RPI at 19.2Kbps DTE speed enabled |
+H2 | RPI at 38.4Kbps DTE speed enabled |
+H3 | RPI at 57.6Kbps DTE speed enabled |
+H11 | RPI + mode enabled |
+H16 | Video ready mode enabled |
S(STATUS) -REGISTERS
AUTOSYNC OPTIONS | |
Type: | Register |
Format | AT [cmds] S19=n [cmds] |
Description: | Sets autosync options. Further information is unavailable |
AUTOSYNC/SYNC | |
Type: | Register |
Format | AT [cmds] S20=n [cmds] |
Range: | 0-255 |
Unit: | Unidentiified |
Description: | Sets autosync HDLC address or BSC sync character. Further information is unavailable |
BIT-MAPPED REGISTER S21 | |
Type: | Register |
Format | AT [cmds] S21=n [cmds] |
Range: | Unidentiified |
Description: | Selects V.24/General bit mapped options. Further information is unavailable |