TEM-336P PCMCIA modem/telephone/ISDN Settings and Configuration

TRENDWARE INTERNATIONAL

TEM-336P PCMCIA

Card Type
Modem, Fax
Chip Set
Unidentified
Maximum Modem Rate
33.6Kbps
Maximum Fax Rate
14.4Kbps
Data Modulation Protocol
Bell 103A/212A
ITU-T V.21, V.22, V.22bis, V.32, V.32bis, V.34, V.34bis
Fax Modulation Protocol
ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression
MNP5, V.42, V.42bis
Fax Class
Class I
Data Bus
PCMCIA

TRENDWARE-INTERNATIONAL-Modem-Fax-TEM-336P-PCMCIA

SUPPORTED COMMAND SET
Basic AT Commands
AT, A/
A, E, H, M, P, Q, T, V, W
&C, &F, &G, &V, &Z
Extended AT Commands
\J, \T, \V
Special Commands
-C
S Registers
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S30
Note: See MHI Help File for full command documentation.

Proprietary AT Command Set

COMMUNICATION PROTOCOLS
Type:
Configuration
Format:
AT [cmds] Bn [cmds]
Description:
Selects the communication protocol for data calls
Note: The B command allows the simultaneous selection of more than one suffix, enabling multiple protocols.
Command
Protocol
B0
ITU-T V.22 at 1200bps
B1
Bell 212A at 1200bps
B2
V.23 at 1200/75bps
B3
V.23 at 75/1200bps
B15
V.21 at 300bps
B16
Bell 103 at 300bps

DIAL
Type:
Immediate
Format:
AT [cmds] D<#> [cmds]
Description:
Dials telephone number according to any modifiers included in the string
Note:
Any combination of modifiers can be used to produce the desired dial functions in sequence.
Command
Function
DL
Re-dial last number
DP
Pulse dialing enabled
DR
Answer mode enabled; originate mode disabled following handshake initiation.
DS=n
Dial stored telephone number n
DT
Tone dialing enabled/Pulse dialing disabled
DW
Dialing resumed following dial tone detection
D,
Dialing paused for amount of time specified in S8 register
D!
Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.
D@
Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.
D;
Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.

AUTO-MODE DETECTION
Type:
Configuration
Format:
AT [cmds] Nn [cmds]
Description:
Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed.
Command
Function
N0
Auto-mode detection disabled
í N1
In originate mode, handshake begins at line speed designated by the S37 register. Modem can shift to a slower speed if necessary.
In answer mode, handshake attempted with the following protocols in order - V.FC, V.32bis, V.32, V.22bis, V.22 or Bell 212, V.21, and Bell 103

ON-LINE
Type:
Immediate
Format:
AT [cmds] On [cmds]
Description:
Controls on-line command (data transmission) state options.
Note: The O command must be placed at the end of the command string.
Command
Function
O0
On-line command mode with no retraining enabled
O1
On-line command mode with retraining enabled
O3
Issue a rate re-negotiate, then return to on-line state

SELECT CALL PROGRESS RESULT CODES
Type:
Configuration
Format:
AT [cmds] Xn [cmds]
Description:
Enables selection of tone detection and associated result code format options
Command
Function
X0
Busy and dial tone detection disabled; result codes 0 - 4 enabled.
X1
Busy and dial tone detection disabled; result codes 0 - 5 & 10 enabled.
X2
Busy tone detection disabled, dial tone detection enabled; result codes 0 - 6 & 10 enabled.
X3
Busy tone detection enabled, dial tone detection disabled; result codes 0 - 5, 7 & 10 enabled.
í X4
Busy and dial tone detection enabled; result codes 0 - 7 & 10 enabled.
X5
Busy and dial tone detection enabled; result codes 0 - 7 & 10 enabled.
X6
Busy and dial tone detection enabled; result codes 0 - 7 & 10 enabled.
X7
Display CONNECT or "1" for all speeds. Check dial tone and busy tone

SOFT RESET
Type:
Immediate
Format:
AT [cmds] Zn [cmds]
Description:
Restores modem profiles previously saved in non-volatile RAM using the &W command.
Command
Function
Z0
Restore setting 0
Z1
Restore setting 0

DATA TERMINAL READY (DTR)
Type:
Configuration
Format:
AT [cmds] &Dn [cmds]
Description:
Selects modem response to DTR
Command
Function
í &D0
Modem does not respond to DTR
&D1
Modem goes to command mode after DTR goes is off
&D2
Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled.
&D3
Modem is initialized after DTR goes off

FLOW CONTROL
Type:
Configuration
Format:
AT [cmds] &Kn [cmds]
Description:
Enables flow control options
Command
Function
&K0
Flow control disabled
í &K3
RTS/CTS flow control enabled
&K4
XON/XOFF flow control enabled

PULSE DIALING RATIO
Type:
Configuration
Format:
AT [cmds] &Pn [cmds]
Description:
Selects pulse dial make/break ratio
Command
Function
í &P0
39/61ms at 10pps (North America)
&P1
33/67ms at 10pps (Europe)

COMMUNICATIONS MODE
Type:
Configuration
Format:
AT [cmds] &Qn [cmds]
Description:
Selects communications mode options
Command
Mode
í &Q0
Buffered asynchronous mode, serial port speed follows connect speed.
&Q5
Error correction mode
&Q8
MNP error control mode
&Q9
V.42 or MNP error control mode

DATA SET READY (DSR)
Type:
Configuration
Format:
AT [cmds] &Sn [cmds]
Description:
Selects DSR options
Command
Function
&S0
DSR forced high
í &S1
DSR high only while modem is handshaking or connected

TEST MODES
Type:
Immediate
Format:
AT [cmds] &Tn
Description:
Selects test options
Command
Function
&T0
End current test
&T1
Begin local analog loopback test
&T3
Begin local digital loopback
&T6
Request remote digital loopback

STORE ACTIVE PROFILE
Type:
Configuration
Format:
AT [cmds] &Wn [cmds]
Description:
Writes the values for the active profile into the non-volatile RAM

Extended AT Commands

CONNECT MODE
Type:
Configuration
Format:
AT [cmds] \Nn [cmds]
Description:
Controls the type of connection the modem will operate in
Command
Function
\N0
Normal mode enabled
\N1
Direct mode enabled
\N2
Reliable mode enabled
\N3
Auto-reliable mode enabled
\N4
V.42 reliable mode enabled

FLOW CONTROL TYPE
Type:
Configuration
Format:
AT [cmds] \Qn [cmds]
Description:
Sets type of flow control used by modem
Command
Function
\Q0
Flow control disabled
\Q1
Bidirectional XON/XOFF flow control enabled
\Q3
Bidirectional RTS/CTS flow control enabled

BLACKLIST
Type:
Configuration
Format:
AT [cmds] %Bn [cmds]
Description:
View numbers in blacklist

COMPRESSION
Type:
Configuration
Format:
AT [cmds] %Cn [cmds]
Description:
Selects data compression
Command
Function
%C0
Data compression disabled
%C1
V.42bis/MNP5 enabled

S(status) -REGISTERS

V.34 MODULATION
Format
AT [cmds] S28=n [cmds]
Default:
1
Range:
0-255
Description:
Controls the V.34 modulation
Command
Function
S28=0
Disabled
S28=1-255
Enabled

ERROR CORRECTION NEGOTIATION
Type:
Register
Format
AT [cmds] S36=n [cmds]
Description:
Selects the action of the modem if it fails to connect with the error-correction protocol set in &Q.
Command
Function
S36=0, 2
Hang up
S36=1, 3
Attempt a direct connection
S36=4, 6
Attempt a connection at MNP2-4; if that fails, hang up.
S36=5, 7
Attempt a connection at MNP2-4; if that fails, attempt a direct connection.

DCE LINE SPEED
Type:
Register
Format
AT [cmds] S37=n [cmds]
Description:
Sets the maximum allowable data exchange rate attempted during handshake process.
Command
Function
í S37=0
Maximum modem speed
S37=2
1200/75bps
S37=3
300bps
S37=5
1200bps
S37=6
2400bps
S37=7
4800bps
S37=8
7200bps
S37=9
9600bps
S37=10
12000bps
S37=11
14400bps
S37=12
16800bps
S37=13
19200bps
S37=14
21600bps
S37=15
24000bps
S37=16
26400bps
S37=17
28800bps
S37=18
31200bps
S37=19
33600bps

DIAL LINE RATE
Type:
Register
Format
AT [cmds] S38=n [cmds]
Description:
56K dial line rate selection
Command
Function
í S38=0
56K disabled
S38=1
56K enabled, auto-speed selection, maximum modem speed
S38=2
32000bps
S38=3
34000bps
S38=4
36000bps
S38=5
38000bps
S38=6
40000bps
S38=7
42000bps
S38=8
44000bps
S38=9
46000bps
S38=10
48000bps
S38=11
50000bps
S38=12
52000bps
S38=13
54000bps
S38=14
56000bps

SLEEP TIMER
Type:
Register
Format
AT [cmds] S89 [cmds]
Range:
0 - 60
Unit:
1 second
Description:
Sleep mode control timer
Command
Function
0
Disable sleep mode
5 - 60
Number of seconds of inactivity before entering sleep mode

TRANSMISSION LEVEL (JAPANESE VERSION ONLY)
Type
Register or Configuration
Format
AT [cmds] S91=n [cmds]
Default
14
Range
6 - 15
Unit
-1 dBm
Description
Sets the signal level for transmission over leased-lines

FEATURE NEGOTIATION OPTIONS
Type:
Register
Format:
AT [cmds] S48=n [cmds]
Description:
Selects active error correction and compression protocols
Command
Function
S48=7
Detection negotiation and XID negotiation enabled
S48=128
Fall-back to options set in S36

Headaches Begone! A Systemic Approach To Healing Your Headaches

Don't Let Your Bike Seat Ruin Your Sex Life Book

TEM-336P PCMCIA modem/telephone/ISDN Settings and Configuration

Search

My Books

Discover

Card Type	Modem, Fax
Chip Set	Unidentified
Maximum Modem Rate	33.6Kbps
Maximum Fax Rate	14.4Kbps
Data Modulation Protocol	Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.32, V.32bis, V.34, V.34bis
Fax Modulation Protocol	ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression	MNP5, V.42, V.42bis
Fax Class	Class I
Data Bus	PCMCIA

COMMUNICATION PROTOCOLS
Type:	Configuration
Format:	AT [cmds] Bn [cmds]
Description:	Selects the communication protocol for data calls
Note: The B command allows the simultaneous selection of more than one suffix, enabling multiple protocols.
Command	Protocol
B0	ITU-T V.22 at 1200bps
B1	Bell 212A at 1200bps
B2	V.23 at 1200/75bps
B3	V.23 at 75/1200bps
B15	V.21 at 300bps
B16	Bell 103 at 300bps

DIAL
Type:	Immediate
Format:	AT [cmds] D<#> [cmds]
Description:	Dials telephone number according to any modifiers included in the string
Note:	Any combination of modifiers can be used to produce the desired dial functions in sequence.
Command	Function
DL	Re-dial last number
DP	Pulse dialing enabled
DR	Answer mode enabled; originate mode disabled following handshake initiation.
DS=n	Dial stored telephone number n
DT	Tone dialing enabled/Pulse dialing disabled
DW	Dialing resumed following dial tone detection
D,	Dialing paused for amount of time specified in S8 register
D!	Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.
D@	Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.
D;	Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.

AUTO-MODE DETECTION
Type:	Configuration
Format:	AT [cmds] Nn [cmds]
Description:	Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed.
Command	Function
N0	Auto-mode detection disabled
í N1	In originate mode, handshake begins at line speed designated by the S37 register. Modem can shift to a slower speed if necessary. In answer mode, handshake attempted with the following protocols in order - V.FC, V.32bis, V.32, V.22bis, V.22 or Bell 212, V.21, and Bell 103

ON-LINE
Type:	Immediate
Format:	AT [cmds] On [cmds]
Description:	Controls on-line command (data transmission) state options.
Note: The O command must be placed at the end of the command string.
Command	Function
O0	On-line command mode with no retraining enabled
O1	On-line command mode with retraining enabled
O3	Issue a rate re-negotiate, then return to on-line state

SELECT CALL PROGRESS RESULT CODES
Type:	Configuration
Format:	AT [cmds] Xn [cmds]
Description:	Enables selection of tone detection and associated result code format options
Command	Function
X0	Busy and dial tone detection disabled; result codes 0 - 4 enabled.
X1	Busy and dial tone detection disabled; result codes 0 - 5 & 10 enabled.
X2	Busy tone detection disabled, dial tone detection enabled; result codes 0 - 6 & 10 enabled.
X3	Busy tone detection enabled, dial tone detection disabled; result codes 0 - 5, 7 & 10 enabled.
í X4	Busy and dial tone detection enabled; result codes 0 - 7 & 10 enabled.
X5	Busy and dial tone detection enabled; result codes 0 - 7 & 10 enabled.
X6	Busy and dial tone detection enabled; result codes 0 - 7 & 10 enabled.
X7	Display CONNECT or "1" for all speeds. Check dial tone and busy tone

SOFT RESET
Type:	Immediate
Format:	AT [cmds] Zn [cmds]
Description:	Restores modem profiles previously saved in non-volatile RAM using the &W command.
Command	Function
Z0	Restore setting 0
Z1	Restore setting 0

DATA TERMINAL READY (DTR)
Type:	Configuration
Format:	AT [cmds] &Dn [cmds]
Description:	Selects modem response to DTR
Command	Function
í &D0	Modem does not respond to DTR
&D1	Modem goes to command mode after DTR goes is off
&D2	Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled.
&D3	Modem is initialized after DTR goes off

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] &Kn [cmds]
Description:	Enables flow control options
Command	Function
&K0	Flow control disabled
í &K3	RTS/CTS flow control enabled
&K4	XON/XOFF flow control enabled

PULSE DIALING RATIO
Type:	Configuration
Format:	AT [cmds] &Pn [cmds]
Description:	Selects pulse dial make/break ratio
Command	Function
í &P0	39/61ms at 10pps (North America)
&P1	33/67ms at 10pps (Europe)

COMMUNICATIONS MODE
Type:	Configuration
Format:	AT [cmds] &Qn [cmds]
Description:	Selects communications mode options
Command	Mode
í &Q0	Buffered asynchronous mode, serial port speed follows connect speed.
&Q5	Error correction mode
&Q8	MNP error control mode
&Q9	V.42 or MNP error control mode

DATA SET READY (DSR)
Type:	Configuration
Format:	AT [cmds] &Sn [cmds]
Description:	Selects DSR options
Command	Function
&S0	DSR forced high
í &S1	DSR high only while modem is handshaking or connected

TEST MODES
Type:	Immediate
Format:	AT [cmds] &Tn
Description:	Selects test options
Command	Function
&T0	End current test
&T1	Begin local analog loopback test
&T3	Begin local digital loopback
&T6	Request remote digital loopback

STORE ACTIVE PROFILE
Type:	Configuration
Format:	AT [cmds] &Wn [cmds]
Description:	Writes the values for the active profile into the non-volatile RAM

CONNECT MODE
Type:	Configuration
Format:	AT [cmds] \Nn [cmds]
Description:	Controls the type of connection the modem will operate in
Command	Function
\N0	Normal mode enabled
\N1	Direct mode enabled
\N2	Reliable mode enabled
\N3	Auto-reliable mode enabled
\N4	V.42 reliable mode enabled

FLOW CONTROL TYPE
Type:	Configuration
Format:	AT [cmds] \Qn [cmds]
Description:	Sets type of flow control used by modem
Command	Function
\Q0	Flow control disabled
\Q1	Bidirectional XON/XOFF flow control enabled
\Q3	Bidirectional RTS/CTS flow control enabled

BLACKLIST
Type:	Configuration
Format:	AT [cmds] %Bn [cmds]
Description:	View numbers in blacklist

COMPRESSION
Type:	Configuration
Format:	AT [cmds] %Cn [cmds]
Description:	Selects data compression
Command	Function
%C0	Data compression disabled
%C1	V.42bis/MNP5 enabled

V.34 MODULATION
Format	AT [cmds] S28=n [cmds]
Default:	1
Range:	0-255
Description:	Controls the V.34 modulation
Command	Function
S28=0	Disabled
S28=1-255	Enabled

ERROR CORRECTION NEGOTIATION
Type:	Register
Format	AT [cmds] S36=n [cmds]
Description:	Selects the action of the modem if it fails to connect with the error-correction protocol set in &Q.
Command	Function
S36=0, 2	Hang up
S36=1, 3	Attempt a direct connection
S36=4, 6	Attempt a connection at MNP2-4; if that fails, hang up.
S36=5, 7	Attempt a connection at MNP2-4; if that fails, attempt a direct connection.

DCE LINE SPEED
Type:	Register
Format	AT [cmds] S37=n [cmds]
Description:	Sets the maximum allowable data exchange rate attempted during handshake process.
Command	Function
í S37=0	Maximum modem speed
S37=2	1200/75bps
S37=3	300bps
S37=5	1200bps
S37=6	2400bps
S37=7	4800bps
S37=8	7200bps
S37=9	9600bps
S37=10	12000bps
S37=11	14400bps
S37=12	16800bps
S37=13	19200bps
S37=14	21600bps
S37=15	24000bps
S37=16	26400bps
S37=17	28800bps
S37=18	31200bps
S37=19	33600bps

DIAL LINE RATE
Type:		Register
Format		AT [cmds] S38=n [cmds]
Description:		56K dial line rate selection
Command	Function
í S38=0	56K disabled
S38=1	56K enabled, auto-speed selection, maximum modem speed
S38=2	32000bps
S38=3	34000bps
S38=4	36000bps
S38=5	38000bps
S38=6	40000bps
S38=7	42000bps
S38=8	44000bps
S38=9	46000bps
S38=10	48000bps
S38=11	50000bps
S38=12	52000bps
S38=13	54000bps
S38=14	56000bps

SLEEP TIMER
Type:	Register
Format	AT [cmds] S89 [cmds]
Range:	0 - 60
Unit:	1 second
Description:	Sleep mode control timer
Command	Function
0	Disable sleep mode
5 - 60	Number of seconds of inactivity before entering sleep mode

TRANSMISSION LEVEL (JAPANESE VERSION ONLY)
Type	Register or Configuration
Format	AT [cmds] S91=n [cmds]
Default	14
Range	6 - 15
Unit	-1 dBm
Description	Sets the signal level for transmission over leased-lines

FEATURE NEGOTIATION OPTIONS
Type:			Register
Format:	AT [cmds] S48=n [cmds]
Description:	Selects active error correction and compression protocols
Command		Function
S48=7		Detection negotiation and XID negotiation enabled
S48=128		Fall-back to options set in S36