PM144HC II (VER. 2) modem/telephone/ISDN Settings and Configuration

PRACTICAL PERIPHERALS, INC.

PM144HC II (VER. 2)

Card Type
Modem (asynchronous)
Chipset
Unidentified
Maximum Data Rate
14.4Kbps
Maximum Fax Rate
14.4Kbps
Data Bus
8-bit ISA
Fax Class
Class I & II
Data Modulation
Bell 103A/212A
ITU-T V.21, V.22, V.22bis, V.32, V.32bis
Fax Modulation
V.17, V.27ter, V.29
Error Correction/Compression
MNP5, V.42bis

CONNECTIONS
Function
Label
Function
Label
Line in/out
CN1
Line in/out
CN2

SERIAL PORT ADDRESS SELECTION
Setting
JP1
3F8h (COM1:)
Pins 1 & 2, 7 & 8 closed
2F8h (COM2:)
Pins 1 & 2, 8 & 9 closed
3E8h (COM3:)
Pins 2 & 3, 7 & 8 closed
2E8h (COM4:)
Pins 2 & 3, 8 & 9 closed

INTERRUPT SELECTION
Setting
JP1
IRQ2
Pins 10 & 11 closed
IRQ3
Pins 11 & 12 closed
IRQ4
Pins 5 & 6 closed
IRQ5
Pins 4 & 5 closed

SUPPORTED STANDARD COMMANDS
Basic AT Commands
+++, ‘comma’, A/
A, D, E, H, L, M, N, Q, V, W, X, Y, Z
&D, &F, &K, &V, &W, &Y, &Z
S-Registers
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S18, S25, S30, S36, S38, S46, S48, S82
S86, S95, S108, S109, S110
Note: See MHI documentation for complete information.

UNIDENTIFIED COMMANDS
Command
Default
S37
0
S43
0

Proprietary AT Command Set

AUTO-ANSWER MODE
Type:
Configuration
Format:
AT [cmds] &An [cmds]
Description:
Sets the mode the modem will operate in on auto-answer.
Command
Function
í &A0
Modem auto-answers in answer mode.
&A1
Modem auto-answers in originate mode.

AUTO-RETRAIN
Type:
Configuration
Format:
AT [cmds] &Bn [cmds]
Description:
Selects whether the modem will automatically perform a retrain sequence when line conditions change.
Command
Function
&B0
Auto-retrain disabled.
í &B1
Auto-retrain enabled.

CD SIGNAL
Type:
Configuration
Format:
AT [cmds] &Cn [cmds]
Description:
Controls the behaviour of the CD signal.
Command
Function
í &C0
CD forced high.
&C1
CD forced high after carrier signal is detected.
&C2
CD forced high except during disconnect.

COMMUNICATIONS MODE
Type:
Configuration
Format:
AT [cmds] &Qn [cmds]
Description:
Selects the communications mode the modem will use.
Command
Mode
&Q0
Asynchronous direct mode.
í &Q5
Asynchronous V.42 reliable mode.
&Q6
Buffered asynchronous mode.
&Q8
Asynchronous MNP reliable mode.
&Q9
Asynchronous V.42bis only mode.

DISPLAY INFORMATION
Type:
Immediate
Format:
AT [cmds] In [cmds]
Description:
Displays information requested about the modem.
Command
Function
I0
Displays product identification code.
I1
Displays ROM checksum.
I2
Tests and reports ROM checksum.
I3
Displays firmware revision.
I4
Displays feature bitmap.

EXTENDED RING
Type:
Register
Format:
AT [cmds] S101=n [cmds]
Default:
0
Range:
0-255
Unit:
Bit-mapped
Description:
Selects which extended ring types the modem will respond to.
Bit
Value
Function
0
í 0
1
Do not respond to ring type A.
Respond to ring type A.
1
í 0
1
Do not respond to ring type B.
Respond to ring type B.
2
í 0
1
Do not respond to ring type C.
Respond to ring type C.
3
í 0
1
Do not respond to ring type D.
Respond to ring type D.
4
í 0
1
Do not respond to ring type E.
Respond to ring type E.
5
í 0
1
Do not respond to ring type F.
Respond to ring type F.
6
í 0
1
Do not respond to ring type G.
Respond to ring type G.
7
í 0
1
Report RING for all ring types.
Report RING n where n is the ring type.

ON-LINE
Type:
Immediate
Format:
AT [cmds] On
Description:
Instructs the modem to return to on-line state.
Command
Function
O0
Return to on-line state.
O1
Return to on-line state and initiate retrain sequence.
O3
Return to on-line state and initiate renegotiation sequence.

PROTOCOL
Type:
Configuration
Format:
AT [cmds] Bn [cmds]
Description:
Selects the communication protocol for low-speed data calls.
Command
Protocol
B0
Modem will use ITU-T V.22 at 1200bps.
í B1
Modem will use Bell 212A at 1200bps.
B2
Modem will use ITU-T V.23 at receive 1200/transmit 75bps.
B3
Modem will use ITU-T V.23 at receive 75/transmit 1200bps.
B15
Modem will use ITU-T V.21 at 300bps.
í B16
Modem will use Bell 103A at 300bps.

TRELLIS CODING
Type:
Configuration
Format:
AT [cmds] &Un [cmds]
Description:
Selects whether the modem will use trellis coding.
Command
Function
í &U0
Trellis coding enabled.
&U1
Trellis coding disabled.

Headaches Begone! A Systemic Approach To Healing Your Headaches

Don't Let Your Bike Seat Ruin Your Sex Life Book

PM144HC II (VER. 2) modem/telephone/ISDN Settings and Configuration

Search

My Books

Discover

Card Type	Modem (asynchronous)
Chipset	Unidentified
Maximum Data Rate	14.4Kbps
Maximum Fax Rate	14.4Kbps
Data Bus	8-bit ISA
Fax Class	Class I & II
Data Modulation	Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.32, V.32bis
Fax Modulation	V.17, V.27ter, V.29
Error Correction/Compression	MNP5, V.42bis

CONNECTIONS
Function	Label	Function	Label
Line in/out	CN1	Line in/out	CN2

SERIAL PORT ADDRESS SELECTION
Setting	JP1
3F8h (COM1:)	Pins 1 & 2, 7 & 8 closed
2F8h (COM2:)	Pins 1 & 2, 8 & 9 closed
3E8h (COM3:)	Pins 2 & 3, 7 & 8 closed
2E8h (COM4:)	Pins 2 & 3, 8 & 9 closed

INTERRUPT SELECTION
Setting	JP1
IRQ2	Pins 10 & 11 closed
IRQ3	Pins 11 & 12 closed
IRQ4	Pins 5 & 6 closed
IRQ5	Pins 4 & 5 closed

AUTO-ANSWER MODE
Type:	Configuration
Format:	AT [cmds] &An [cmds]
Description:	Sets the mode the modem will operate in on auto-answer.
Command		Function
í &A0		Modem auto-answers in answer mode.
&A1		Modem auto-answers in originate mode.

AUTO-RETRAIN
Type:	Configuration
Format:	AT [cmds] &Bn [cmds]
Description:	Selects whether the modem will automatically perform a retrain sequence when line conditions change.
Command		Function
&B0		Auto-retrain disabled.
í &B1		Auto-retrain enabled.

CD SIGNAL
Type:	Configuration
Format:	AT [cmds] &Cn [cmds]
Description:	Controls the behaviour of the CD signal.
Command	Function
í &C0	CD forced high.
&C1	CD forced high after carrier signal is detected.
&C2	CD forced high except during disconnect.

COMMUNICATIONS MODE
Type:	Configuration
Format:	AT [cmds] &Qn [cmds]
Description:	Selects the communications mode the modem will use.
Command	Mode
&Q0	Asynchronous direct mode.
í &Q5	Asynchronous V.42 reliable mode.
&Q6	Buffered asynchronous mode.
&Q8	Asynchronous MNP reliable mode.
&Q9	Asynchronous V.42bis only mode.

DISPLAY INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested about the modem.
Command	Function
I0	Displays product identification code.
I1	Displays ROM checksum.
I2	Tests and reports ROM checksum.
I3	Displays firmware revision.
I4	Displays feature bitmap.

EXTENDED RING
Type:		Register
Format:		AT [cmds] S101=n [cmds]
Default:		0
Range:		0-255
Unit:		Bit-mapped
Description:		Selects which extended ring types the modem will respond to.
Bit	Value	Function
0	í 0 1	Do not respond to ring type A. Respond to ring type A.
1	í 0 1	Do not respond to ring type B. Respond to ring type B.
2	í 0 1	Do not respond to ring type C. Respond to ring type C.
3	í 0 1	Do not respond to ring type D. Respond to ring type D.
4	í 0 1	Do not respond to ring type E. Respond to ring type E.
5	í 0 1	Do not respond to ring type F. Respond to ring type F.
6	í 0 1	Do not respond to ring type G. Respond to ring type G.
7	í 0 1	Report RING for all ring types. Report RING n where n is the ring type.

ON-LINE
Type:	Immediate
Format:	AT [cmds] On
Description:	Instructs the modem to return to on-line state.
Command	Function
O0	Return to on-line state.
O1	Return to on-line state and initiate retrain sequence.
O3	Return to on-line state and initiate renegotiation sequence.

PROTOCOL
Type:	Configuration
Format:	AT [cmds] Bn [cmds]
Description:	Selects the communication protocol for low-speed data calls.
Command	Protocol
B0	Modem will use ITU-T V.22 at 1200bps.
í B1	Modem will use Bell 212A at 1200bps.
B2	Modem will use ITU-T V.23 at receive 1200/transmit 75bps.
B3	Modem will use ITU-T V.23 at receive 75/transmit 1200bps.
B15	Modem will use ITU-T V.21 at 300bps.
í B16	Modem will use Bell 103A at 300bps.

TRELLIS CODING
Type:	Configuration
Format:	AT [cmds] &Un [cmds]
Description:	Selects whether the modem will use trellis coding.
Command		Function
í &U0		Trellis coding enabled.
&U1		Trellis coding disabled.