1040 modem/telephone/ISDN Settings and Configuration

PATTON ELECTRONICS COMPANY

1040

Card Type
Short Range Modem
Chip Set
Unidentified
I/O Options
25-pin serial port (RS-232),
network interface via RJ-45, RJ-11, or terminal block
Wiring Type
Unshielded twisted pair
Maximum Data Rate
38.4Kbps
Data Bus
External

CONNECTIONS
Function
Label
Function
Label
DTE/DCE serial port (25-pin connector)
CN1
Twisted pair connector
CN2
Note: CN2 is available as either a terminal block, standard RJ-11, or RJ-45 connector

USER CONFIGURABLE SETTINGS
Setting
Label
Position
í Modem is in asynchronous mode
SW1/7
On
Modem is in synchronous mode
SW1/7
Off
í Carrier forced high
SW1/8
Off
Carrier controlled by RTS
SW1/8
On
í Asynchronous tolerance range from -2.5% to +1%
SW2/3
Off
Asynchronous tolerance range from -2.5% to +2.3%
SW2/3
On
í V.52/V.54 tests enabled
SW2/8
Off
V.52/V.54 tests enabled
SW2/8
On

DATA RATE
Setting
SW1/1
SW1/2
SW1/3
SW1/4
1200bps
On
On
On
On
1800bps
Off
On
On
On
2400bps
On
Off
On
On
3600bps
Off
Off
On
On
4800bps
On
On
Off
On
7200bps
Off
On
Off
On
í 9600bps
On
Off
Off
On
14.4Kbps
Off
Off
Off
On
19.2Kbps
On
On
On
Off
28.8Kbps
Off
On
On
Off
38.4Kbps
On
On
Off
Off

TRANSMIT CLOCK SOURCE
Source
SW1/5
SW1/6
í Transmit clock generated internally
On
On
Transmit clock derived from terminal interface
Off
On
Receive recover clock
On
Off

CHARACTER LENGTH
Setting
SW2/1
SW2/2
8 bits
Off
On
9 bits
On
On
í 10 bits
Off
Off
11 bits
On
Off

RTS/CTS DELAY
Setting
SW2/4
SW2/5
í 7ms delay
On
On
53ms delay
Off
On
No delay
On
Off
No delay
Off
Off

WIRE MODE SELECTION
Setting
SW2/6
SW2/7
í 4-wire (full duplex)
On
Off
4-wire (half duplex)
On
On
2-wire (half duplex)
Off
On

TEST PATTERN GENERATOR
Function
Label
Position
511 test pattern transmitted
SW3
1
Normal operation. Test pattern not activated
SW3
2
511/E test pattern transmitted (intentional errors inserted)
SW3
3

LOOPBACK TEST SELECTOR
Function
Label
Position
Activates local analog loopback
SW4
1
Normal operation. Loopback not activated
SW4
2
Remote digital loopback initiated
SW4
3

DIAGNOSTIC LED(S)
LED
Color
Status
Condition
ER
Red
On
Bit error likely in received signal or error detected in 511 or 511/E test pattern
ER
Red
Off
Error not detected
TST
Red
On
Device has been placed in test mode by local or remote user
TST
Red
Off
Device is not conducting a test

Headaches Begone! A Systemic Approach To Healing Your Headaches

Don't Let Your Bike Seat Ruin Your Sex Life Book

1040 modem/telephone/ISDN Settings and Configuration

Search

My Books

Discover

Card Type	Short Range Modem
Chip Set	Unidentified
I/O Options	25-pin serial port (RS-232), network interface via RJ-45, RJ-11, or terminal block
Wiring Type	Unshielded twisted pair
Maximum Data Rate	38.4Kbps
Data Bus	External

CONNECTIONS
Function		Label		Function		Label
DTE/DCE serial port (25-pin connector)	CN1		Twisted pair connector		CN2
Note: CN2 is available as either a terminal block, standard RJ-11, or RJ-45 connector

USER CONFIGURABLE SETTINGS
Setting	Label	Position
í Modem is in asynchronous mode	SW1/7	On
Modem is in synchronous mode	SW1/7	Off
í Carrier forced high	SW1/8	Off
Carrier controlled by RTS	SW1/8	On
í Asynchronous tolerance range from -2.5% to +1%	SW2/3	Off
Asynchronous tolerance range from -2.5% to +2.3%	SW2/3	On
í V.52/V.54 tests enabled	SW2/8	Off
V.52/V.54 tests enabled	SW2/8	On

TRANSMIT CLOCK SOURCE
Source	SW1/5	SW1/6
í Transmit clock generated internally	On	On
Transmit clock derived from terminal interface	Off	On
Receive recover clock	On	Off

CHARACTER LENGTH
Setting	SW2/1	SW2/2
8 bits	Off	On
9 bits	On	On
í 10 bits	Off	Off
11 bits	On	Off

RTS/CTS DELAY
Setting	SW2/4	SW2/5
í 7ms delay	On	On
53ms delay	Off	On
No delay	On	Off
No delay	Off	Off

WIRE MODE SELECTION
Setting	SW2/6	SW2/7
í 4-wire (full duplex)	On	Off
4-wire (half duplex)	On	On
2-wire (half duplex)	Off	On

TEST PATTERN GENERATOR
Function	Label	Position
511 test pattern transmitted	SW3	1
Normal operation. Test pattern not activated	SW3	2
511/E test pattern transmitted (intentional errors inserted)	SW3	3

LOOPBACK TEST SELECTOR
Function	Label	Position
Activates local analog loopback	SW4	1
Normal operation. Loopback not activated	SW4	2
Remote digital loopback initiated	SW4	3

DIAGNOSTIC LED(S)
LED	Color	Status	Condition
ER	Red	On	Bit error likely in received signal or error detected in 511 or 511/E test pattern
ER	Red	Off	Error not detected
TST	Red	On	Device has been placed in test mode by local or remote user
TST	Red	Off	Device is not conducting a test