1092A modem/telephone/ISDN Settings and Configuration

PATTON ELECTRONICS COMPANY

1092A

Card Type
Modem
Chip Set
Unidentified
I/O Options
AC power connector, DTE/DCE serial port,
network interface via RJ-45 connector
Wiring Type
RJ-45 shielded twisted pair
Maximum Data Rate
128Kbps (synchronous), 38.4Kbps (asynchronous)
Data Bus
External

CONNECTIONS
Function
Label
Function
Label
AC power connector
CN1
DCE/DTE strap
CN4
DTE/DCE port (QuikConnectä module)
CN2
Power switch
SW3
Network interface via RJ-45 connector
CN3

Note:
QuikConnectä serial interface module can be configured as a V.24/RS-232, V.35, RS422/530, or X.21 port. The DTE/DCE strap (X.21 only) is default configured for DCE interface. To change the interface to DTE, rotate the strap 180 degrees so the DTE arrows point to the X.21 port.

USER CONFIGURABLE SETTINGS
Setting
Label
Position
í DSR on during local line loop
S1/3
On
DSR off during local line loop
S1/3
Off
í Modem responds to remote digital loopback requests from remote modem
S1/8
On
Modem ignores RDL requests from remote modem
S1/8
Off
í Factory configured - do not alter
S2/2
Off
í Modem ignores LAL requests from DTE
S2/3
Off
Modem responds to local analog loopback requests from DTE
S2/3
On
í 2-wire twisted pair operation enabled
S2/4
On
4-wire twisted pair operation enabled
S2/4
Off
í Factory configured - do not alter
S2/5
Off
í Modem responds to remote digital loopback requests from DTE
S2/6
On
Modem ignores RDL requests from DTE
S2/6
Off

ASYC/SYNC OPERATION
Setting
S1/4
S1/5
í Factory configured - do not alter (async/sync operation enabled)
Off
Off

DATA RATE
Synchronous Data Rate
Asynchronous Data Rate
S1/1
S1/2
S2/1
19.2Kbps
Reserved
Off
Off
On
32Kbps
Reserved
On
On
Off
56Kbps
Reserved
Off
On
Off
í 64Kbps
Reserved
On
Off
Off
128Kbps
0-38.4Kbps
Off
Off
Off

TRANSMIT CLOCK SOURCE
Source
S1/6
S1/7
í Transmit clock generated internally
On
On
Transmit clock derived from terminal interface
Off
On
Transmit clock derived from receive line signal
On
Off
Hardware reset
Off
Off

CONTROL PORT DATA RATE
Setting
S2/7
S2/8
í 9600bps
On
On
19.2Kbps
Off
On

LOOPBACK TEST SELECTOR
Function
Label
Position
Activates local analog loopback
SW4
1
Normal operation. Loopback not activated
SW4
2
Remote digital loopback initiated
SW4
3

TEST PATTERN GENERATOR
Function
Label
Position
511/E test pattern transmitted (intentional errors inserted)
SW5
1
Normal operation. Test pattern not activated
SW5
2
511 test pattern transmitted
SW5
3

DIAGNOSTIC LED(S)
LED
Color
Status
Condition
TD
Red
On
Data is being transmitted (low logic level, device idle)
TD
Green
On
Data is being transmitted (high logic level)
TD
None
Off
Data is not being transmitted
RD
Red
On
Data is being received (low logic level, device idle)
RD
Green
On
Data is being received (high logic level)
RD
None
Off
Data is not being received
CTS
Green
On
CTS signal is high
CTS
Green
Off
CTS signal is low
CD
Green
On
Carrier signal detected
CD
Red
On
Carrier signal not detected
DTR
Green
On
DTR signal is high
DTR
Green
Off
DTR signal is low
NS
Red
On
Local modem is not connected to remote modem
NS
Red
Off
Local modem is connected to remote modem
ER
Red
On
Bit error likely in received signal or error detected in 511 or 511/E test pattern
ER
Red
Off
Error not detected
TM
Red
On
Device has been placed in test mode by local or remote user
TM
Red
Off
Device is not conducting a test

Headaches Begone! A Systemic Approach To Healing Your Headaches

Don't Let Your Bike Seat Ruin Your Sex Life Book

1092A modem/telephone/ISDN Settings and Configuration

Search

My Books

Discover

Card Type	Modem
Chip Set	Unidentified
I/O Options	AC power connector, DTE/DCE serial port, network interface via RJ-45 connector
Wiring Type	RJ-45 shielded twisted pair
Maximum Data Rate	128Kbps (synchronous), 38.4Kbps (asynchronous)
Data Bus	External

CONNECTIONS
Function			Label		Function		Label
AC power connector		CN1		DCE/DTE strap		CN4
DTE/DCE port (QuikConnectä module)		CN2		Power switch		SW3
Network interface via RJ-45 connector		CN3
Note:	QuikConnectä serial interface module can be configured as a V.24/RS-232, V.35, RS422/530, or X.21 port. The DTE/DCE strap (X.21 only) is default configured for DCE interface. To change the interface to DTE, rotate the strap 180 degrees so the DTE arrows point to the X.21 port.

USER CONFIGURABLE SETTINGS
Setting	Label	Position
í DSR on during local line loop	S1/3	On
DSR off during local line loop	S1/3	Off
í Modem responds to remote digital loopback requests from remote modem	S1/8	On
Modem ignores RDL requests from remote modem	S1/8	Off
í Factory configured - do not alter	S2/2	Off
í Modem ignores LAL requests from DTE	S2/3	Off
Modem responds to local analog loopback requests from DTE	S2/3	On
í 2-wire twisted pair operation enabled	S2/4	On
4-wire twisted pair operation enabled	S2/4	Off
í Factory configured - do not alter	S2/5	Off
í Modem responds to remote digital loopback requests from DTE	S2/6	On
Modem ignores RDL requests from DTE	S2/6	Off

ASYC/SYNC OPERATION
Setting	S1/4		S1/5
í Factory configured - do not alter (async/sync operation enabled)		Off		Off

DATA RATE
Synchronous Data Rate		Asynchronous Data Rate			S1/1		S1/2		S2/1
19.2Kbps			Reserved			Off		Off			On
32Kbps			Reserved			On		On			Off
56Kbps	Reserved			Off			On			Off
í 64Kbps	Reserved			On			Off			Off
128Kbps	0-38.4Kbps			Off			Off			Off

TRANSMIT CLOCK SOURCE
Source	S1/6	S1/7
í Transmit clock generated internally	On	On
Transmit clock derived from terminal interface	Off	On
Transmit clock derived from receive line signal	On	Off
Hardware reset	Off	Off

CONTROL PORT DATA RATE
Setting		S2/7		S2/8
í 9600bps			On		On
19.2Kbps	Off			On

LOOPBACK TEST SELECTOR
Function	Label	Position
Activates local analog loopback	SW4	1
Normal operation. Loopback not activated	SW4	2
Remote digital loopback initiated	SW4	3

TEST PATTERN GENERATOR
Function	Label	Position
511/E test pattern transmitted (intentional errors inserted)	SW5	1
Normal operation. Test pattern not activated	SW5	2
511 test pattern transmitted	SW5	3

DIAGNOSTIC LED(S)
LED	Color	Status	Condition
TD	Red	On	Data is being transmitted (low logic level, device idle)
TD	Green	On	Data is being transmitted (high logic level)
TD	None	Off	Data is not being transmitted
RD	Red	On	Data is being received (low logic level, device idle)
RD	Green	On	Data is being received (high logic level)
RD	None	Off	Data is not being received
CTS	Green	On	CTS signal is high
CTS	Green	Off	CTS signal is low
CD	Green	On	Carrier signal detected
CD	Red	On	Carrier signal not detected
DTR	Green	On	DTR signal is high
DTR	Green	Off	DTR signal is low
NS	Red	On	Local modem is not connected to remote modem
NS	Red	Off	Local modem is connected to remote modem
ER	Red	On	Bit error likely in received signal or error detected in 511 or 511/E test pattern
ER	Red	Off	Error not detected
TM	Red	On	Device has been placed in test mode by local or remote user
TM	Red	Off	Device is not conducting a test