ACCULINK 3350 E1 modem/telephone/ISDN Settings and Configuration

PARADYNE CORPORATION

ACCULINK 3350 E1

Card Type
Network Termination Unit
NIC Type
E1
Chip Set
Unidentified
I/O Options
BNC connectors (2), auxiliary port (RJ-48), communication port (RJ-48), HDSL network interface via RJ-48 connector, test jacks (6), power jack
15-pin G.703 DTE port
Maximum Data Rate
2.048Mbps
Data Bus
External

CONNECTIONS
Function
Label
Function
Label
Test jack - Lp1 HDSL line
CN1
Auxiliary port
CN8
Test jack - Lp2 HDSL line
CN2
Communication port
CN9
Test jack - E1 line in
CN3
15-pin DTE port
CN10
Test jack - E1 line out
CN4
HDSL network interface via RJ-48 connector
CN11
Test jack - E1 monitor In
CN5
BNC connector - receive
RX
Test jack - E1 monitor out
CN6
BNC connector - transmit
TX
Power Jack
CN7

USER CONFIGURABLE SETTINGS
Setting
Label
Position
Open shield connection established
SW1
On
Earth shield connection established
SW1
Off
120ohm balanced network interface selected
SW2
In
75ohm unbalanced network interface selected
SW2
Out
Note: SW1 must be on when using the 120ohm interface

DIAGNOSTIC LED(S)
LED
Color
Status
Condition
OK
Green
On
NTU power is on
OK
Green
Blinking
NTU is downloading software
OK
Green
Off
NTU power is off or detecting a system failure
FAIL
Yellow
On
Device error has been detected
FAIL
Yellow
Off
Device error has not been detected
FAIL
Yellow
Blinking
NTU is conducting a self test
TST
Yellow
On
NTU is executing a loopback or pattern test
TST
Yellow
Off
NTU is not executing a test
SIG1
Green
On
NTU is receiving a recoverable signal from network on loop 1
SIG1
Green
Off
NTU cannot recover the signal from network on loop 1
SIG2
Green
On
NTU is receiving a recoverable signal from network on loop 2
SIG2
Green
Off
NTU cannot recover the signal from network on loop 2
OOF
Yellow
On
Out of frame condition detected on network
OOF
Yellow
Off
Out of frame condition not detected on network
ALM
Yellow
On
Alarm condition detected on network
ALM
Yellow
Off
Alarm condition not detected on network
SIG
Green
On
A recoverable signal is being received from G.703 DTE port
SIG
Green
Off
NTU cannot recover the signal from G.703 DTE port
OFG
Yellow
On
Out of frame condition detected on G.703 DTE signal
OFG
Yellow
Off
Out of frame condition not detected on G.703 DTE signal
ALMG
Yellow
On
Alarm condition detected on G.703 DTE signal
ALMG
Yellow
Off
Alarm condition not detected on G.703 DTE signal
PDV
Yellow
On
A pulse density violation was detected (and corrected) on G.703 DTE signal
PDV
Yellow
Off
A pulse density violation was not detected on G.703 DTE signal
BPV
Yellow
On
A bipolar violation was detected (and corrected) on G.703 DTE signal
BPV
Yellow
Off
A bipolar violation was not detected on G.703 DTE signal

Headaches Begone! A Systemic Approach To Healing Your Headaches

Don't Let Your Bike Seat Ruin Your Sex Life Book

ACCULINK 3350 E1 modem/telephone/ISDN Settings and Configuration

Search

My Books

Discover

Card Type	Network Termination Unit
NIC Type	E1
Chip Set	Unidentified
I/O Options	BNC connectors (2), auxiliary port (RJ-48), communication port (RJ-48), HDSL network interface via RJ-48 connector, test jacks (6), power jack 15-pin G.703 DTE port
Maximum Data Rate	2.048Mbps
Data Bus	External

CONNECTIONS
Function	Label	Function	Label
Test jack - Lp1 HDSL line	CN1	Auxiliary port	CN8
Test jack - Lp2 HDSL line	CN2	Communication port	CN9
Test jack - E1 line in	CN3	15-pin DTE port	CN10
Test jack - E1 line out	CN4	HDSL network interface via RJ-48 connector	CN11
Test jack - E1 monitor In	CN5	BNC connector - receive	RX
Test jack - E1 monitor out	CN6	BNC connector - transmit	TX
Power Jack	CN7

USER CONFIGURABLE SETTINGS
Setting	Label	Position
Open shield connection established	SW1	On
Earth shield connection established	SW1	Off
120ohm balanced network interface selected	SW2	In
75ohm unbalanced network interface selected	SW2	Out
Note: SW1 must be on when using the 120ohm interface

DIAGNOSTIC LED(S)
LED	Color	Status	Condition
OK	Green	On	NTU power is on
OK	Green	Blinking	NTU is downloading software
OK	Green	Off	NTU power is off or detecting a system failure
FAIL	Yellow	On	Device error has been detected
FAIL	Yellow	Off	Device error has not been detected
FAIL	Yellow	Blinking	NTU is conducting a self test
TST	Yellow	On	NTU is executing a loopback or pattern test
TST	Yellow	Off	NTU is not executing a test
SIG1	Green	On	NTU is receiving a recoverable signal from network on loop 1
SIG1	Green	Off	NTU cannot recover the signal from network on loop 1
SIG2	Green	On	NTU is receiving a recoverable signal from network on loop 2
SIG2	Green	Off	NTU cannot recover the signal from network on loop 2
OOF	Yellow	On	Out of frame condition detected on network
OOF	Yellow	Off	Out of frame condition not detected on network
ALM	Yellow	On	Alarm condition detected on network
ALM	Yellow	Off	Alarm condition not detected on network
SIG	Green	On	A recoverable signal is being received from G.703 DTE port
SIG	Green	Off	NTU cannot recover the signal from G.703 DTE port
OFG	Yellow	On	Out of frame condition detected on G.703 DTE signal
OFG	Yellow	Off	Out of frame condition not detected on G.703 DTE signal
ALMG	Yellow	On	Alarm condition detected on G.703 DTE signal
ALMG	Yellow	Off	Alarm condition not detected on G.703 DTE signal
PDV	Yellow	On	A pulse density violation was detected (and corrected) on G.703 DTE signal
PDV	Yellow	Off	A pulse density violation was not detected on G.703 DTE signal
BPV	Yellow	On	A bipolar violation was detected (and corrected) on G.703 DTE signal
BPV	Yellow	Off	A bipolar violation was not detected on G.703 DTE signal