OC-7111 modem/telephone/ISDN Settings and Configuration

Card Type	Fax, Modem (asynchronous)
Chip Set	Unidentified
Maximum Data Rate	28.8Kbps
Maximum Fax Rate	14.4Kbps
Data Bus	PCMCIA Type II
Fax Class	Class I & II
Data Modulation Protocol	Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Rockwell V.FC
Fax Modulation Protocol	ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression	MNP5, MNP10, V.42, V.42bis

MISCELLANEOUS TECHNICAL NOTES

Note: Due to country specific parameters, S-register settings are unidentified.

AUTOSYNC™
Format		AT [cmds] S19=n [cmds]
Default:		Unidentified
Range:		0-30
Unit:		Bit-mapped
Description:		Sets options for Hayes AutoSync™ functions.
Bit	Value	Function
0	0	Not used.
1	0 1	BSC enabled. HDLC enabled.
2	0 1	HDLC address detection disabled. HDLC address detection enabled.
3	0 1	NRZI bit encoding enabled. NRZ2 bit encoding enabled.
4	0 1	Mark idle enabled. Flag or sync idle enabled.

AUTOSYNC HDLC ADDRESS
Type:	Register
Format:	AT [cmds] S20=n [cmds]
Default:	Unidentified
Range:	0-255
Unit:	Unidentified
Description:	Sets the HDLC address/BSC character

AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD
Type:	Configuration
Format:	AT [cmds] %En [cmds]
Description:	Controls auto-retrain mode and fallback/fall-forward
Command	Function
í %E0	Auto-retrain disabled
%E1	Auto-retrain enabled
%E2	Auto-fallback/fall-forward enabled
%E3	Auto-retrain enabled with fast hang-up

BIT MAPPED REGISTERS
Register	Default
S14	Unidentified
S21	Unidentified
S22	Unidentified
S23	Unidentified
S27	Unidentified
S28	Unidentified
S31	Unidentified
S40	Unidentified
S41	Unidentified
S201	Unidentified

BREAK SEND
Type:	Configuration
Format:	AT [cmds] \Bn [cmds]
Default:	3
Range:	1-9
Unit:	.1 second
Description:	Sends break to modem

BREAK TYPE
Type:		Configuration
Format:		AT [cmds] \Kn [cmds]
Description:		Configures action of break signal
Command	Break from DTE		Modem receives \B	Break received from remote modem
\K0	Online command mode enabled, send no break to remote modem		Break sent to remote modem and buffered cleared	Buffers cleared, break sent to DTE
\K1	Break sent to remote modem and buffered cleared		Break sent to remote modem and buffered cleared	Buffers cleared, break sent to DTE
\K2	Online command mode enabled, send no break to remote modem		Send break to remote modem immediately	Break sent immediately to DTE
\K3	Send break to remote modem immediately		Send break to remote modem immediately	Break sent immediately to DTE
\K4	Online command mode enabled, send no break to remote modem		Send break with transmitted data	Break sent with received data to the DTE
í \K5	Send break with transmitted data		Send break with transmitted data	Break sent with received data to the DTE

COUNTRY CODE
Type:	Configuration
Format:	AT [cmds] *NCnn [cmds]
Description:	Select a country code from NVRAM (nn=00-08)

DIAL
Type:	Immediate
Format:	AT [cmds] D<#> [cmds]
Description:	Dials telephone number according to any modifiers included in the string
Note:	Any combination of modifiers can be used to produce the desired dial functions in sequence.
Command	Function
DJ	Link will be negotiated at 1200bps for current call only
DK	Power level adjustment enabled for current call only
DL	Re-dial last number
DP	Pulse dialing enabled
DT	Tone dialing enabled/Pulse dialing disabled
DR	Accepted but not used.
DS=n	Dial stored telephone number n
D!	Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.
DW	Dialing resumed following dial tone detection
D@	Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.
D,	Dialing paused for amount of time specified in S8 register
D;	Modem returned to command state after dialing. The semicolon can only be placed at the end of the dial command.
D^	Calling tone enabled/disabled for current dialing attempt

DIALING CODE
Type:	Configuration
Format:	AT [cmds] *Zn [cmds]
Description:	Select the dial code for pulse dialing
Command		Function
í *Z0		Use dial code 0
*Z1		Use dial code 1

DELAYED NUMBERS
Type:	Immediate
Format:	AT [cmds] *B [cmds]
Description:	Displays delayed numbers list

DELAYED NUMBERS
Type:	Immediate
Format:	AT [cmds] *D [cmds]
Description:	Displays delayed numbers list

COMPRESSION
Type:	Configuration
Format:	AT [cmds] %Cn [cmds]
Description:	Selects data compression
Command	Function
%C0	Data compression disabled
%C1	MNP5 enabled
%C2	V.42bis enabled
í %C3	MNP5 and V.42bis enabled

CONNECT MODE
Type:	Configuration
Format:	AT [cmds] \Nn [cmds]
Description:	Controls the type of connection the modem will operate in
Command	Function
\N0	Normal mode enabled
\N1	Direct mode enabled
\N2	MNP reliable mode enabled
í \N3	Auto-reliable mode enabled
\N4	V.42 reliable mode enabled
\N5	MNP auto-reliable mode enabled

FLASH DIAL MODIFIER TIME
Type:	Register
Format	AT [cmds] S29=n [cmds]
Default:	0
Range:	0-255
Unit:	Unidentified
Description:	Time the modem will go on-hook upon receiving the ! dial modifier in dial string.

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] \Gn [cmds]
Description:	Selects modem port flow control
Command	Function
í \G0	Flow control disabled
\G1	Flow control enabled

FLOW CONTROL CHARACTER - XOFF
Type:	Register
Format:	AT [cmds] S33=n [cmds]
Default:	19
Range:	0-255
Unit:	ASCII
Description:	Sets the character used to represent XOFF

FLOW CONTROL CHARACTER - XON
Type:	Register
Format:	AT [cmds] S32=n [cmds]
Default:	17
Range:	0-255
Unit:	ASCII
Description:	Sets the character used to represent XON

LINE SIGNAL LEVEL
Type:	Immediate
Format:	AT [cmds] %L [cmds]
Description:	Returns a value which indicates the received line signal level

LINE SIGNAL QUALITY
Type:	Immediate
Format:	AT [cmds] %Q [cmds]
Description:	Returns a value which indicates line signal quality

LOCK SERIAL PORT
Type:	Configuration
Format:	AT [cmds] \Jn [cmds]
Description:	Sets operation of serial port speed
Command	Function
í \J0	Serial speed locked
\J1	Serial speed follows connect speed

MAXIMUM BLOCK SIZE FOR TRANSMISSION
Type:	Configuration
Format:	AT [cmds] \An [cmds]
Description:	Sets the maximum transmittable block size
Command	Function
\A0	MNP block size is 64 characters
í \A1	MNP block size is 128 characters
\A2	MNP block size is 192 characters
\A3	MNP block size is 256 characters

MODULATION SELECTION DISPLAY
Type:	Immediate
Format:	AT [cmds] +MS? [cmds]
Description:	Displays modulation, automode, minimum rate and maximum rate settings
Command		Function
+MS=?		Displays supported mode selection

MODULATION SELECTION
Type:	Configuration
Format:	AT [cmds] +MS=x,y,z,a [cmds]
Description:	Sets options for active protocol; the transfer rates specified by z and a must be valid for the protocol selected.
Command	Function
x=0	V.21
x=1	V.22
x=2	V.22bis
x=3	V.23
x=9	V.32
x=10	V.32bis
x=11	V.34
x=64	Bell 103
x=69	Bell 212A
x=74	V.FC
y=0	Automode disabled
y=1	Auto-detect highest speed enabled
z, a=300	Set minimum or maximum transfer rate at 300bps, respectively.
z, a=1200	Set minimum or maximum transfer rate at 1200bps, respectively.
z, a=2400	Set minimum or maximum transfer rate at 2400bps, respectively.
z, a=4800	Set minimum or maximum transfer rate at 4800bps, respectively.
z, a=7200	Set minimum or maximum transfer rate at 7200bps, respectively.
z, a=9600	Set minimum or maximum transfer rate at 9600bps, respectively.
z, a=12000	Set minimum or maximum transfer rate at 12000bps, respectively.
z, a=14400	Set minimum or maximum transfer rate at 14400bps, respectively.
z, a=16800	Set minimum or maximum transfer rate at 16800bps, respectively.
z, a=19200	Set minimum or maximum transfer rate at 19200bps, respectively.
z, a=21600	Set minimum or maximum transfer rate at 21600bps, respectively.
z, a=24000	Set minimum or maximum transfer rate at 24000bps, respectively.
z, a=26400	Set minimum or maximum transfer rate at 26400bps, respectively.
z, a=28800	Set minimum or maximum transfer rate at 28800bps, respectively.

MNP - EXTENDED SERVICES
Type:	Configuration
Format:	AT [cmds] -Kn [cmds]
Description:	Selects MNP extended services
Command	Function
í -K0	MNP extended services disabled
-K1	MNP extended services enabled

MNP - STREAM/BLOCK MODE
Type:	Configuration
Format:	AT [cmds] \Ln [cmds]
Description:	Selects the transfer mode for MNP link
Command	Function
í \L0	Stream mode for MNP enabled
\L1	Block mode for MNP enabled

MNP10 - FALLBACK
Type:	Configuration
Format:	AT [cmds] -Qn [cmds]
Description:	Allows MNP10 to fall back to speeds slower than 4800bps
Command	Function
-Q0	MNP10 at 2400 and 1200bps enabled
-Q1	MNP10 at 2400 and 1200bps disabled

MNP10 - LINK NEGOTIATION
Type:	Configuration
Format:	AT [cmds] *Hn [cmds]
Description:	Sets the speed at which MNP10 link negotiation will occur
Command	Function
*H0	Link will be negotiated at highest possible speed
*H1	Link will be negotiated at 1200bps
*H2	Link will be negotiated at 4800bps

MNP10 - POWER LEVEL ADJUST
Type:	Configuration
Format:	AT [cmds] )Mn [cmds]
Description:	Controls automatic transmit power level adjustment during MNP 10 link negotiation
Command	Function
í )M0	Power level adjustment disabled
)M1	Power level adjustment enabled

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested
Command	Function
I0	Reports product code
I1	Reports ROM checksum
I2	Calculates and reports ROM checksum
I3	Reports firmware level
I5	Reports country code

SLEEP TIMER
Type:	Register
Format	AT [cmds] S24=n [cmds]
Default:	0
Range:	Unidentified
Unit:	Unidentified
Description:	Maximum duration of DTE and DCE inactivity allowed prior to initiating low-power sleep mode.

STORED NUMBERS
Type:	Immediate
Format:	AT [cmds] \Fn [cmds]
Description:	Displays phone number directory

TEST MODES
Type:		Register
Format:		AT [cmds] S16=n [cmds]
Default:		Unidentified
Range:		0-125
Unit:		Bit-mapped
Description:		Controls loopback tests, analog, digital, remote digital, and self tests.
Bit	Value	Function
0	0 1	Local analog loopback not in progress Local analog loopback in progress
1	0	Not used
2	0 1	Local digital loopback not in progress Local digital loopback in progress
3	0 1	Modem not in remote digital loopback Remote digital loopback in progress
4	0 1	Remote digital loopback not requested Remote digital loopback requested
5	0 1	Remote digital loopback w/ self-test not in progress Remote digital loopback w/ self-test in progress
6	0 1	Local analog loopback w/ self-test not in progress Local analog loopback w/ self-test in progress

TRANSMISSION LEVEL - CELLULAR
Type:	Configuration
Format:	AT [cmds] @Mn [cmds]
Default:	Unidentified
Range:	0-31
Unit:	-1dBm
Description:	Sets the signal level for transmission while in cellular mode

TRANSMISSION LEVEL - FAX
Type:	Register
Format:	AT [cmds] S92=n [cmds]
Default:	Unidentified
Range:	0-15
Unit:	-1 dBm
Description:	Sets the signal level for transmission while in fax mode

TRANSMISSION LEVEL - PSTN
Type	Register
Format	AT [cmds] S91=n [cmds]
Default	Unidentified
Range	0-15
Unit	-1 dBm
Description	Sets the signal level for transmission over switched phone lines

V.32 - COMPROMISE EQUALIZER
Type:	Configuration
Format:	AT [cmds] :En [cmds]
Description:	Controls V.32 compromise equalizer
Command	Function
:E0	Equalizer disabled
í :E1	Equalizer enabled