NETCOMM LIMITED
THE OFFICIAL X-FILES MODEM 144 (MNP10EC)
Card Type | Modem (asynchronous) |
Chipset | Unidentified |
Maximum Data Rate | 14.4Kbps |
Maximum Fax Rate | 14.4Kbps |
Data Modulation | Bell 103A, 212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis |
Fax Modulation | ITU-T V.17, V.27ter, V.29 |
Error Correction/Compression | MNP5, MNP10EC, V.42, V.42bis |
Fax Class | Class I & II |
Data Bus | Serial |
NETCOMM-LIMITED-Modem-asynchronous-THE-OFFICIAL-X-245
DIAGNOSTIC LED(S) | |||
LED | Color | Status | Condition |
TM | Red | On | Modem is in test mode |
TM | Red | Off | Modem is not in test mode |
TD | Red | Blinking | Modem is transmitting data |
TD | Red | Off | Modem is not transmitting data |
RD | Red | Blinking | Modem is receiving data |
RD | Red | Off | Modem is not receiving data |
OH | Red | On | Modem is off-hook |
OH | Red | Off | Modem is on-hook |
CD | Red | On | Carrier signal detected |
CD | Red | Off | Carrier signal not detected |
AA | Red | On | Auto-answer enabled |
AA | Red | Off | Auto-answer disabled |
AA | Red | Blinking | Phone is ringing |
TR | Red | On | DTR signal is high |
TR | Red | Off | DTR signal is low |
CP | Red | On | Compression enabled |
CP | Red | Off | Compression disabled |
EC | Red | On | Error correction enabled |
EC | Red | Off | Error correction disabled |
POWER | Red | On | Power is on |
POWER | Red | Off | Power is off |
MISCELLANEOUS TECHNICAL NOTES |
Diagram not available. |
SUPPORTED STANDARD COMMANDS |
Basic AT Commands |
+++, ‘comma’, A/ |
A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z |
&C, &D, &F, &G, &K, &Q, &R, &S, &V, &W, &Y, &Z |
Extended AT Commands |
\A, \B, \G, \L, \N, \V |
%C, %E, %L, %Q |
Special AT Commands |
:E, -K |
S-Registers |
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S18, S24, S25, S29, S30, S32, S33, S38 |
S48, S82, S86, S95 |
Note: See MHI help file for complete information. |
UNIDENTIFIED COMMANDS | |
Command | Default |
\K | Unidentified |
*S | Unidentified |
Proprietary AT Command Set
MNP10EC MODE | ||
Type: | Configuration | |
Format: | AT [cmds] -SEC=n [cmds] | |
Description: | Selects whether the modem will attempt to use MNP10EC mode during the handshaking sequence. | |
Command | Function | |
-SEC=0 | MNP10EC handshaking disabled unless a V.34 connection is attempted via a cellular line. | |
í -SEC=1 | MNP10EC handshaking enabled. |
PROTOCOL/SPEED | |
Type: | Configuration |
Format: | AT [cmds] Fn [cmds] |
Description: | Selects the protocol and speed the modem will attempt to connect at. |
Command | Function |
F0 | Auto-detect the highest common connect speed. |
F1 | Select V.21 or Bell 103 at 300bps speed. |
F3 | Select V.23 at 75/1200bps speed. |
F4 | Select V.22 or Bell 212A at 1200bps speed. |
F5 | Select V.22bis at 2400bps speed. |
F6 | Select V.32 or V.32bis at 4800bps speed. |
F7 | Select V.32bis at 7200bps speed. |
F8 | Select V.32bis or V.32 at 9600bps speed. |
F9 | Select V.32bis at 12Kbps speed. |
F10 | Select V.32bis at 14.4Kbps speed. |
See NETCOMM LIMITED THE OFFICIAL X-FILES MODEM 336 (MNP10) for a full command summary.