MOBILESURFR 56K modem/telephone/ISDN Settings and Configuration

Card Type	Modem (asynchronous)
Chip Set	Unidentified
Maximum Modem Rate	56Kbps
Maximum Fax Rate	14.4Kbps
Data Modulation Protocol	Bell 103/212 ITU-T V.34, V.32bis, V.32, V.22bis, V.22, V.21, K56flex
Fax Modulation Protocol	ITU-T V.17, V.29, V.27ter, V.21 channel 2
Error Correction/Compression	V.42, V.42bis, MNP5, MNP10, MNP10EC
Fax Class	Unidentified
Data Bus	PCMCIA Type II

SUPPORTED COMMAND SET

Basic AT Commands

AT, ‘+++’, A/

A, B, E, H, M, O, Q, V, W, X, Y, Z

&C, &P, &R, &T, &V, &W, &Y, &Z

Extended AT Commands

\A, \B, \K, \N, \V

%C, %E, %L, %Q

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25,

S26, S27, S28, S30, S31, S32, S33, S36, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92, S95

Special Commands

-K, #CID, +MS

Note: See MHI Help File for full command documentation.

AUTO-MODE DETECTION
Type:	Configuration
Format:	AT [cmds] Nn [cmds]
Description:	Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed.
Command	Function
N0	Automode detection disable
í N1	Automode detection enable

DATA SET READY (DSR)
Type:	Configuration
Format:	AT [cmds] &Sn [cmds]
Description:	Selects DSR options
Command	Function
&S0	DSR forced high
í &S1	DSR high only while modem is handshaking or connected

DATA TERMINAL READY (DTR)
Type:	Configuration
Format:	AT [cmds] &Dn [cmds]
Description:	Selects modem response to DTR
Note: The action each variant of &D causes depends on the setting of &Q
Command	Function
&D0	Modem does not respond to DTR
&D1	Modem goes to command mode after DTR goes is off
í &D2	Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled.
&D3	Modem is initialized after DTR goes off

DIAL
Type:	Immediate
Format:	AT [cmds] D<#> [cmds]
Description:	Dials telephone number according to any modifiers included in the string
Note:	Any combination of modifiers can be used to produce the desired dial functions in sequence.
Command	Function
DL	Re-dial last number
DP	Pulse dialing enabled
DS=n	Dial stored telephone number n
DT	Tone dialing enabled/Pulse dialing disabled
DW	Dialing resumed following dial tone detection
D,	Dialing paused for amount of time specified in S8 register
D!	Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.
D@	Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.
D;	Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.

FACTORY DEFAULT PROFILE
Type:	Configuration
Format:	AT [cmds] &F [cmds]
Description:	Sets values in active profile to values found in the default profile
Command	Function
í &F0	Load factory setting 0
&F1	Load factory setting 1

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] &Kn [cmds]
Description:	Enables flow control options
Command	Function
&K0	Flow control disabled
í &K3	Bi-directional RTS/CTS flow control enabled
&K4	Bi-directional XON/XOFF flow control enabled
&K5	Transparent XON/XOFF flow control enabled
&K6	RTS/CTS and XON/XOFF flow control enabled

GUARD TONE
Type:	Configuration
Format:	AT [cmds] &Gn [cmds]
Description:	Commands the modem to transmit a guard tone in V.22/V.22bis
Note: Used primarily for international data transmission
Command	Function
í &G0	Guard tone disabled
&G1	Guard tone disabled
&G2	1800Hz guard tone enabled

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested
Command	Function
I0	Reports product code
I1	Reports EPROM CRC value
I2	Displays OK
I3	Reports firmware revision number
I4	Reports Motorola 56K
I5	Reports country code parameter
I6	Reports data pump model and code revision

SPEAKER MODE
Type:	Configuration
Format:	AT [cmds] Mn [cmds]
Description:	Selects various speaker options
Command	Function
M0	Speaker disabled

SPEAKER VOLUME
Type:	Configuration
Format:	AT [cmds] Ln [cmds]
Description:	Controls speaker volume
Command	Function
L0	Speaker disabled

TRANSMIT CARRIER
Type:	Configuration
Format:	AT [cmds] Cn [cmds]
Description:	Controls the transmit carrier switching
Note: Command performs no function; included for compatibility only.

DISTINCTIVE RING
Type:	Configuration
Format:	AT [cmds] -SDR=n [cmds]
Description:	Controls distinctive ring
Command	Function
-SDR=0	Distinctive ring disable
-SDR=1	Distinctive ring enable ring type A
-SDR=2	Distinctive ring enable ring type B
-SDR=3	Distinctive ring enable ring type A and B
-SDR=4	Distinctive ring enable ring type C
-SDR=5	Distinctive ring enable ring type A and C
-SDR=6	Distinctive ring enable ring type B and C
-SDR=7	Distinctive ring enable ring type A, B, and C

MNP10-EC
Type:	Configuration
Format:	AT [cmds] -SECn [cmds]
Description:	Controls MNP10-EC
Command	Function
-SEC0	Disable
-SEC1	Enable and set TX level (0-30dB/m)

AUTO-SYNC OPTIONS
Type:	Register
Format	AT [cmds] S19=n [cmds]
Default:	0
Range:	Unidentified
Unit:	1 second
Description:	Sets the auto-sync options

HDLC ADDRESS
Type:	Register
Format	AT [cmds] S20=n [cmds]
Default:	0
Range:	Unidentified
Unit:	1 second
Description:	Sets the HDLC address or BSC sync character