XPVS 56IF (SF-1156HV/TX(X2)) modem/telephone/ISDN Settings and Configuration

Card Type	Modem (asynchronous)
Chip Set	Unidentified
I/O Options	microphone, speaker out, line in, line out
Maximum Modem Rate	56Kbps
Maximum Fax Rate	14.4Kbps
Data Modulation Protocol	Bell 103/212 ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34+, x2
Fax Modulation Protocol	ITU-T V.17, V.27ter, V.29
Error Correction/Compression	MNP5, V.42bis, V.42bis
Fax Class	Unidentified
Data Bus	8-bit ISA
Card Size	Half-length, half-height card

CONNECTIONS
Function	Label		Function		Label
Line out		CN1		Microphone		CN4
Line in		CN2		Speaker out		CN3

USER CONFIGURABLE SETTINGS
Setting	Label	Position
í Speaker type stereo	JP5	Closed
Speaker type mono	JP5	Open

SERIAL PORT ADDRESS
Setting	JP3/A	JP3/B	JP3/C
COM1 (3F8h)	Closed	Closed	Closed
COM2 (2F8h)	Open	Closed	Closed
COM3 (3E8h)	Closed	Open	Closed
COM4 (2E8h)	Open	Open	Closed
PnP	Open	Open	Open

INTERRUPT SELECTION
IRQ	JP2/A	JP2/B	JP2/C	JP2/D	JP2/E
2/9	Closed	Open	Open	Open	Open
3	Open	Closed	Open	Open	Open
4	Open	Open	Closed	Open	Open
5	Open	Open	Open	Closed	Open
7	Open	Open	Open	Open	Closed
PnP	Open	Open	Open	Open	Open

SUPPORTED COMMAND SET

Basic AT Commands

AT, +++, A/

A, B, E, F, H, M, O, P, T, V, X

&C, &G, &T, &W, &Z

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S16, S18, S25, S38

AT Voice Commands

#VBQ?, #VBS, #VBT, #VCI, #VLS, #VRA, #VRN, #VRX, #VSK, #VSP, #VSR, #VSS, #VTD, #VTS,

#VTX, #BDR, #CLS, #MDL, #MFR, #REV?

Note: See MHI Help File for full command documentation.

DISPLAY COMMANDS
Type:	Configuration
Format:	AT [cmds] $ [cmds]
Description:	Displays the basic command set

DIAL
Type:	Immediate
Format:	AT [cmds] D<#> [cmds]
Description:	Dials telephone number according to any modifiers included in the string
Note:	Any combination of modifiers can be used to produce the desired dial functions in sequence.
Command	Function
DL	Re-dial last number
DP	Pulse dialing enabled
DR	Answer mode enabled; originate mode disabled following handshake initiation.
DS=n	Dial stored telephone number n
DT	Tone dialing enabled/Pulse dialing disabled
DW	Dialing resumed following dial tone detection
D,	Dialing paused for amount of time specified in S8 register
D/	Delays for 125msec. before dialing
D!	Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.
D@	Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.
D$	Wait for prompt tone detection function enabled. Waits for prompt tone for amount of time specified by the S7 command.
D;	Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested
Command	Function
I0	Reports modem model and speed
I1	Reports ROM checksum
I2	Tests and reports ROM checksum
I3	Reports product ID
I4	Reports current modem settings
I5	Displays active and stored profiles
I6	Reports data connection information
I7	Reports manufacturer and model information

SPEAKER VOLUME
Type:	Configuration
Format:	AT [cmds] Ln [cmds]
Description:	Controls speaker volume
Command	Function
L0	Low volume setting
L1	Low volume setting
í L2	Medium volume setting
L3	Highest volume setting

RESULT CODES
Type:	Configuration
Format:	AT [cmds] Qn [cmds]
Description:	Enables modem to send result codes to the DTE
Command	Function
í Q0	Result code sending enabled
Q1	Result code sending disabled
Q2	Displays result codes only in Originate Mode

CONFIGURATION PROFILE SELECT
Type:	Configuration
Format:	AT [cmds] Yn [cmds]
Description:	Commands the modem to use Profile 0 or Profile 1
Command	Function
í Y0	Configuration Profile 0 active upon power on or reset
Y1	Configuration Profile 1 active upon power on or reset

SOFT RESET
Type:	Immediate
Format:	AT [cmds] Zn [cmds]
Description:	Restores modem profiles previously saved in non-volatile RAM using the &W command.
Command	Function
Z0	Reset and retrieve active profile set by the Y command
Z1	Reset and retrieve active profile 0
Z2	Reset and retrieve active profile 1
Z3	Reset and retrieve factory default profile 0
Z4	Reset and retrieve factory default profile 1
Z5	Reset and retrieve factory default profile 2

AUTO-ANSWER - ORIGINATE/ANSWER
Type:	Configuration
Format:	AT [cmds] &An [cmds]
Description:	Selects originate or answer mode when in Auto-Answer mode
Command	Function
í &A0	Disable ARQ result codes
&A1	Enable ARQ result codes
&A2	Disable ARQ result codes and V.32 modulation
&A3	Enable ARQ result codes, V.32 modulation, error correction and data compression protocols

DTE RATE ADJUST
Type:	Configuration
Format:	AT [cmds] &Bn [cmds]
Description:	Controls DTE rate
Command	Function
&B0	DTE rate adjust to DCE rate after on line
í &B1	Constant DTE rate
&B2	Constant DTE rate in ARQ mode, variable in non-ARQ mode

DATA TERMINAL READY (DTR)
Type:	Configuration
Format:	AT [cmds] &Dn [cmds]
Description:	Selects modem response to DTR
Note: The action each variant of &D causes depends on the setting of &Q
Command	Function
&D0	Modem does not respond to DTR
&D1	Modem goes to command mode after DTR goes is off
&D2	Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled.

FACTORY DEFAULT PROFILE
Type:	Configuration
Format:	AT [cmds] &F [cmds]
Description:	Sets values in active profile to values found in the default profile
í &F0	Recall factory default configuration 0
&F1	Recall factory default configuration profile 1 (hardware flow control enabled)
&F2	Recall factory default configuration profile 2 (software flow control enabled)

TX FLOW
Type:	Configuration
Format:	AT [cmds] &Hn [cmds]
Description:	Controls TX flow settings
Note: Used primarily for international data transmission
Command	Function
&H0	Disable TX flow controll
í &H1	Enable hardware TX flow control (CTS)
&H2	Enable software TX flow control (XON/XOFF)
&H3	Enable hardware (CTS) and software (XON/XOFF) TX flow control

RX FLOW
Type:	Configuration
Format:	AT [cmds] &In [cmds]
Description:	Controls RX flow settings
Note: Used primarily for international data transmission
Command	Function
í &I0	Disable software RX flow control
&I1	Enable software RX flow control (XON/XOFF)
&I2	Enable software RX flow control (XON/XOFF), but do not pass XON/XOFF to remote modem or local DTE
&I3	Enable HP ENQ/ACK software flow control, host mode
&I4	Enable HP ENQ/ACK software flow control, terminal mode
&I5	Enable software RX flow control (XON/XOFF) for non-ARQ mode

COMPRESSION CONTROL
Type:	Configuration
Format:	AT [cmds] &Kn [cmds]
Description:	Enables compression control options
Command	Function
&K0	Disable V.42bis/MNP5 data compression
í &K1	Auto data compression
&K2	Enable V.42bis/MNP5 data compression
&K3	Disable MNP5 data compression

COMMUNICATIONS MODE
Type:	Configuration
Format:	AT [cmds] &Mn [cmds]
Description:	Selects communications mode
Command	Mode
&M0	Normal mode enabled
í &M4	ARQ and normal modes enabled
&M5	ARQ mode enabled

AUTOMODE CONNECTION SPEED
Type:	Configuration
Format:	AT [cmds] &Nn [cmds]
Description:	Selects connection speed
Command	Mode
í &N0	Enable Automode
&N1	Set connection speed to 300bps
&N2	Set connection speed to 1200bps
&N3	Set connection speed to 2400bps
&N4	Set connection speed to 4800bps
&N5	Set connection speed to 7200bps
&N6	Set connection speed to 9600bps
&N7	Set connection speed to 12000bps
&N8	Set connection speed to 14400bps
&N9	Set connection speed to 16800bps
&N10	Set connection speed to 19200bps
&N11	Set connection speed to 21600bps
&N12	Set connection speed to 24400bps
&N13	Set connection speed to 26400bps
&N14	Set connection speed to 28800bps
&N15	Set connection speed to 31200bps
&N16	Set connection speed to 33600bps
&N17	Set connection speed to 33333bps
&N18	Set connection speed to 37333bps
&N19	Set connection speed to 41333bps
&N20	Set connection speed to 42666bps
&N21	Set connection speed to 44000bps
&N22	Set connection speed to 45333bps
&N23	Set connection speed to 46666bps
&N24	Set connection speed to 48000bps
&N25	Set connection speed to 49333bps
&N26	Set connection speed to 50666bps
&N27	Set connection speed to 52000bps
&N28	Set connection speed to 53333bps
&N29	Set connection speed to 54666bps
&N30	Set connection speed to 56000bps
&N31	Set connection speed to 57333bps

PULSE DIALING RATIO
Type:	Configuration
Format:	AT [cmds] &Pn [cmds]
Description:	Selects pulse dial make/break ratio
Command	Function
í &P0	39/61ms at 10pps (North America)
&P1	33/67ms at 10pps (Europe)

RTS/CTS
Type:	Configuration
Format:	AT [cmds] &Rn [cmds]
Description:	Selects RTS/CTS options
Command	Function
&R0	Reserved
&R1	Modem ignores RTS signal
&R2	Enable RX hardware flow control (RTS)

DATA SET READY (DSR)
Type:	Configuration
Format:	AT [cmds] &Sn [cmds]
Description:	Selects DSR options
Command	Function
í &S0	DSR forced high
&S1	DSR off in command mode, on in on-line mode

MINIMUM DTE CONNECTION
Type:	Configuration
Format:	AT [cmds] &Sn [cmds]
Description:	Selects minimum DTE connection speed
Command	Function
í &U0	Do not set minimum DCE connection speed
&U1	Set connection speed to 300bps
&U2	Set connection speed to 1200bps
&U3	Set connection speed to 2400bps
&U4	Set connection speed to 4800bps
&U5	Set connection speed to 7200bps
&U6	Set connection speed to 9600bps
&U7	Set connection speed to 12000bps
&U8	Set connection speed to 14400bps
&U9	Set connection speed to 16800bps
&U10	Set connection speed to 19200bps
&U11	Set connection speed to 21600bps
&U12	Set connection speed to 24400bps
&U13	Set connection speed to 26400bps
&U14	Set connection speed to 28800bps
&U15	Set connection speed to 31200bps
&U16	Set connection speed to 33600bps
&U17	Set connection speed to 33333bps
&U18	Set connection speed to 37333bps
&U19	Set connection speed to 41333bps
&U20	Set connection speed to 42666bps
&U21	Set connection speed to 44000bps
&U22	Set connection speed to 45333bps
&U23	Set connection speed to 46666bps
&U24	Set connection speed to 48000bps
&U25	Set connection speed to 49333bps
&U26	Set connection speed to 50666bps
&U27	Set connection speed to 52000bps
&U28	Set connection speed to 53333bps
&U29	Set connection speed to 54666bps
&U30	Set connection speed to 56000bps
&U31	Set connection speed to 57333bps

BREAK CONTROL
Type:	Configuration
Format:	AT [cmds] &Yn [cmds]
Description:	Controls the break
Command	Function
&Y0	Destructive break. Does not send break
í &Y1	Destructive break. Break expedited
&Y2	Nondestructive break. Break expedited

BUFFER RESET S13
Format:	AT [cmds] S13=n [cmds]
Unit:	Bit-mapped
Description:	DTR, buffer reset, backspace, autodial. Retrain +++ hangup

ARQ/MNP/V.42bis S15
Format:	AT [cmds] S15=n [cmds]
Unit:	Bit-mapped
Description:	Disable ARQ/MNP/V.42bis

INACTIVITY TIMER
Type:	Register
Format	AT [cmds] S19=n [cmds]
Default:	0
Range:	0-255
Unit:	1 second
Description:	Sets the maximum duration for inactivity
Note: S19=0 disables the timer and allows an indefinite duration.

BIT-MAPPED REGISTER S21
Format	AT [cmds] S21=n [cmds]
Default:	Unidentified
Range:	0-253
Unit:	0.01sec
Description:	Sets the maximum duration for break

FLOW CONTROL CHARACTER - XON
Type:	Register
Format:	AT [cmds] S22=n [cmds]
Default:	17
Range:	0-255
Unit:	ASCII
Description:	Sets the character used to represent XON

FLOW CONTROL CHARACTER - XOFF
Type:	Register
Format:	AT [cmds] S23=n [cmds]
Default:	19
Range:	0-255
Unit:	ASCII
Description:	Sets the character used to represent XOFF

DTR CHANGE THRESHOLD
Type:	Register
Format	AT [cmds] S25=n [cmds]
Default:	5
Range:	0-255
Unit:	.1 second
Description:	Sets maximum time a change in the DTR signal will be ignored
Note: This is the function of this register when &M1 is not set.

BIT-MAPPED REGISTER S27
Type:	Register
Format	AT [cmds] S27=n [cmds]
Default:	5
Range:	0-255
Unit:	Bit-mapped
Description:	V.21 @ 300bps, trellis coding, Disable V.32, answer tone, 9600 result codes, disable V.32bis, enable V.23

ANSWER TONE
Format	AT [cmds] S28=n [cmds]
Default:	8
Range:	0-255
Unit:	0.1 second
Description:	Controls V.32 answer tone.

ANSWER MODE TIMER
Type:	Register
Format	AT [cmds] S29=n [cmds]
Default:	20
Range:	0-255
Unit:	.01 second
Description:	Controls the V.21 answer mode timer.

BIT-MAPPED REGISTER S32
Type:	Register
Format	AT [cmds] S32=n [cmds]
Unit:	Bit-mapped
Description:	V8, V34, V34bis, x2 Enable V.8

BIT-MAPPED REGISTER S33
Format:	AT [cmds] S33=n [cmds]
Unit:	Bit-mapped
Description:	Disable 2400, 2743, 2800, 3000, 3200, and 3429 symbol rates.

BIT-MAPPED REGISTER S34
Format:	AT [cmds] S34=n [cmds]
Unit:	Bit-mapped
Description:	Trellis coding :8S-2D, 16S-4D mapped register 32S-2D, 64S-4D

BIT-MAPPED REGISTER S41
Format	AT [cmds] S41=n [cmds]
Default:	Unidentified
Unit:	Bit-mapped
Description:	Distinctive ring (on=1)