lotus



previous page: CL-MD1414ECP (VF-1114PV1) modem/telephone/ISDN Settings and Configuration
  
page up: Modems and Telephone/ISDN cards Specs: M-O
  
next page: GMV144I modem/telephone/ISDN Settings and Configuration

CL-MD1414ECT modem/telephone/ISDN Settings and Configuration






MAXTECH CORPORATION

CL-MD1414ECT

Card Type

Fax, Modem (asynchronous), Voice

Chip Set

Unidentified

I/O Options

Handset, Voice mail

Maximum Data Rate

14.4Kbps

Maximum Fax Rate

14.4Kbps

Data Bus

8-bit ISA

Fax Class

Class I

Data Modulation Protocol

Bell 103/212A

ITU-T V.21, V.22, V.22bis, V.32, V.32bis

Fax Modulation Protocol

ITU-T V.17, V.21CH2, V.27ter, V.29

Error Correction/Compression

MNP5, V.42, V.42bis

CONNECTIONS

Function

Label

Function

Label

Line in/out

CN1

Line out/in

CN2

SERIAL PORT ADDRESS

Setting

J1

J2

í COM1 (3F8h)

On

On

COM2 (2F8h)

Off

On

COM3 (3E8h)

On

Off

COM4 (2E8h)

Off

Off

INTERRUPT

Setting

J3

J4

J5

J6

2

On

Off

Off

Off

3

Off

On

Off

Off

í 4

Off

Off

On

Off

5

Off

Off

Off

On

Proprietary AT Command Set

ACCEPT MNP RELIABLE MODE

Type:

Immediate

Format:

AT [cmds] \U [cmds]

Description:

Accept remote modemís request for MNP reliable mode

AUTO-FALLBACK/FALL-FORWARD

Type:

Configuration

Format:

AT [cmds] %Gn [cmds]

Description:

Selects auto-fallback/fall-forward

Command

Function

í %G0

Auto-fallback/fall-forward enabled

%G1

Auto-fallback/fall-forward disabled

AUTO-RELIABLE FALLBACK CHARACTER

Type:

Configuration

Format:

AT [cmds] %An [cmds]

Default:

19

Range:

0-127

Unit:

ASCII

Description:

Sets the character used as the auto-reliable fallback character; %A0 will disable this function.

AUTO-RELIABLE TIME BUFFER CONFIGURATION

Type:

Configuration

Format:

AT [cmds] \Cn [cmds]

Description:

Controls the handling of incoming data during auto-reliable time period

Command

Function

í \C0

Data is discarded

\C1

Data is buffered

\C2

Data is discarded; modem returns to normal mode on receiving auto-reliable fallback character.

AUTO-RETRAIN

Type:

Configuration

Format:

AT [cmds] %En [cmds]

Description:

Controls auto-retrain mode

Command

Function

%E0

Auto-retrain disabled

í %E1

Auto-retrain enabled

BIT MAPPED REGISTERS

Register

Default

S14

Unidentified

S16

Unidentified

S21

Unidentified

S22

Unidentified

S23

Unidentified

S27

Unidentified

BREAK TYPE

Type:

Configuration

Format:

AT [cmds] \Kn [cmds]

Default:

5

Range:

0-5

Description:

Configures action of break signal

BREAK SEND

Type:

Configuration

Format:

AT [cmds] \Bn [cmds]

Default:

0

Range:

0-9

Unit:

.1 second

Description:

Sends break to modem

COMPRESSION

Type:

Configuration

Format:

AT [cmds] %Cn [cmds]

Description:

Selects data compression

Command

Function

%C0

MNP5 disabled

í %C1

MNP5 enabled

CONVERT TO MNP RELIABLE MODE

Type:

Immediate

Format:

AT [cmds] \Y [cmds]

Description:

Converts to MNP reliable mode from normal mode

CONNECT MODE

Type:

Configuration

Format:

AT [cmds] \Nn [cmds]

Description:

Controls the type of connection the modem will operate in

Command

Function

\N0

Normal mode enabled

\N1

Direct mode enabled

\N2

MNP mode enabled

í \N3

Auto-reliable mode enabled

\N4

V.42 mode enabled

DIAL

Type:

Immediate

Format:

AT [cmds] D<#> [cmds]

Example:

ATDT555-1212,,1234,

Description:

Dials telephone number according to any modifiers included in the string

Note:

Any combination of modifiers can be used to produce the desired dial functions in sequence.

Modifier

Function

P

Pulse dialing enabled

R

Originate calls in answer mode.

S=n

Dial stored telephone number n. n=0-3

T

Tone dialing enabled

W

Dialing resumed following dial tone detection

,

(Comma) Dialing paused for amount of time specified in S8 register

@

Wait for quiet answer.

!

Flash function initiated.

;

(Semi-colon) Modem returned to command state after dialing.

EXTENDED RESULT CODES

Type:

Configuration

Format:

AT [cmds] \Vn [cmds]

Description:

Selects extended result codes

Command

Function

\V0

Extended result codes disabled

\V1

Extended result codes set 1 enabled

í \V2

Extended result codes set 2 enabled

FLOW CONTROL

Type:

Configuration

Format:

AT [cmds] \Gn [cmds]

Description:

Selects modem port flow control

Command

Function

í \G0

Flow control disabled

\G1

Flow control enabled

FLOW CONTROL TYPE

Type:

Configuration

Format:

AT [cmds] \Qn [cmds]

Description:

Sets type of flow control used by modem

Command

Function

\Q0

Flow control disabled

\Q1

XON/XOFF flow control enabled

\Q2

Unidirectional CTS flow control enabled

í \Q3

Bi-directional RTS/CTS flow control enabled

INACTIVITY TIMER

Type:

Configuration

Format:

AT [cmds] \Tn [cmds]

Default:

0

Range:

0-90

Unit:

1 minute

Description:

Sets the length of time that the modem does not receive information before it disconnects. \T=0 will disable timer.

INACTIVITY TIMER

Type:

Register

Format:

AT [cmds] S90=n [cmds]

Default:

0

Range:

0-255

Unit:

1 second

Description:

Sets the length of time that the modem does not receive information before it disconnects. S90=0 will disable timer.

INITIATE MNP RELIABLE MODE

Type:

Immediate

Format:

AT [cmds] \O [cmds]

Description:

Initiates MNP reliable mode from normal mode

LOCK SERIAL PORT

Type:

Configuration

Format:

AT [cmds] \Jn [cmds]

Description:

Sets operation of serial port speed

Command

Function

í \J0

Serial speed locked

\J1

Serial speed follows connect speed

MAXIMUM BLOCK SIZE FOR TRANSMISSION

Type:

Configuration

Format:

AT [cmds] \An [cmds]

Description:

Sets the maximum transmittable block size

Command

Function

\A0

MNP block size is 64 characters

\A1

MNP block size is 128 characters

\A2

MNP block size is 192 characters

í \A3

MNP block size is 256 characters

REPORT INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays information requested

Command

Function

I0

Reports product identification code

I1

Reports factory ROM ID

I2

Internal memory test

I3

Reports device ID

I4

Reports internal ID

SLEEP TIMER

Type:

Register

Format

AT [cmds] S30=n [cmds]

Default:

10

Range:

0-90

Unit:

1 second

Description:

Maximum duration of DTE and DCE inactivity allowed prior to initiating low-power sleep mode. S30=0 will disable timer.

SWITCH TO NORMAL MODE

Type:

Immediate

Format:

AT [cmds] \Z [cmds]

Description:

Switches to normal mode from MNP mode

V.42 - DETECTION PHASE

Type:

Configuration

Format:

AT [cmds] -Jn [cmds]

Description:

Controls V.42 detection

Command

Function

-J0

V.42 detection disabled

í -J1

V.42 detection enabled

V.42bis - COMPRESSION CONTROL

Type:

Configuration

Format:

AT [cmds] "Hn [cmds]

Description:

Controls V.42bis data compression

Command

Function

"H0

V.42bis disabled

"H1

V.42bis when transmitting enabled

"H2

V.42bis when receiving enabled

í "H3

V.42bis when transmitting/receiving enabled

V.42bis - MAXIMUM BLOCK SIZE

Type:

Immediate

Format:

AT [cmds] "On [cmds]

Default:

32

Range:

6-250

Unit:

Characters

Description:

Selects block size for V.42bis compression

XON/XOFF PASS-THROUGH

Type:

Configuration

Format:

AT [cmds] \Xn [cmds]

Description:

Selects whether XON/XOFF signals are sent to remote modem

Command

Function

í \X0

XON/XOFF signals trapped by local modem

\X1

XON/XOFF passed through local modem








TOP
previous page: CL-MD1414ECP (VF-1114PV1) modem/telephone/ISDN Settings and Configuration
  
page up: Modems and Telephone/ISDN cards Specs: M-O
  
next page: GMV144I modem/telephone/ISDN Settings and Configuration