POWERPORT PLATINUM PRO modem/telephone/ISDN Settings and Configuration

Card Type	Modem (asynchronous), Ethernet
Chipset	Unidentified
Boot ROM	Not available
Network Transfer Rate	10Mbps
Topology	Star
Wire Type	Unshielded twisted pair
Maximum Data Rate	28.8Kbps
Maximum Fax Rate	14.4Kbps
Data Modulation	Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Rockwell V.FC
Fax Modulation	ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression	MNP5, MNP10EC, V.42, V.42bis
Fax Class	Class I
Data Bus	PCMCIA Type II

SUPPORTED STANDARD COMMANDS

Basic AT Commands

+++, ‘comma’, A/

A, D, E, H, M, N, O, V, W, X, Y, Z

&F, &L, &P, &Q, &V, &W, &Y, &Z

Extended AT Commands

\B, \G, \K, \N, \T, \V, \X

%C

S-Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S36, S38, S46, S48, S95

Note: See MHI help file for complete information.

COMMUNICATION PROTOCOLS
Type:	Configuration
Format:	AT [cmds] Bn [cmds]
Description:	Selects the communication protocol for low-speed data calls.
Command	Protocol
B0	Modem will use ITU-T V.22 at 1200bps or 600bps and V.21 at 300bps.
í B1	Modem will use Bell 212A at 1200bps and 103A at 300bps.
B2	Modem will use ITU-T V.23 at 1200/75bps.
B3	Modem will use ITU-T V.23 at 75/1200bps.
B4	Modem will use ITU-T V.23 at 600/75bps.
B5	Modem will use ITU-T V.23 at 75/600bps.

DISPLAY INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested about the modem.
Command	Function
I0	Displays manufacturer and model information.
I1	Displays ROM checksum.
I2	Tests and reports ROM checksum.
I3	Displays product identification code and version.
I4	Displays modem capabilities.
I5	Displays version of DSP chip.
I6	Displays DSP checksum.
I7	Displays release date of firmware.
I8	Displays frequency of the controller clock.
I9	Displays sync frequency of the DSP chip.
I10	Displays DAA type.

LINE SPEED
Type:	Register
Format	AT [cmds] S37=n [cmds]
Description:	Sets the maximum allowable data exchange rate attempted during handshake process.
Command	Function
í S37=0	Speed of last connection
S37=3	Set speed to 300bps.
S37=4	Set speed to 600bps.
S37=5	Set speed to 1200bps.
S37=6	Set speed to 2400bps.
S37=7	Set speed to 4800bps.
S37=8	Set speed to 7200bps.
S37=9	Set speed to 9600bps.
S37=10	Set speed to 12Kbps.
S37=11	Set speed to 14.4Kbps.
S37=12	Set speed to 16.8Kbps.
S37=13	Set speed to 19.2Kbps.
S37=14	Set speed to 21.6Kbps.
S37=15	Set speed to 24Kbps.
S37=16	Set speed to 26.4Kbps.
S37=17	Set speed to 28.8Kbps.

MNP10EC MODE
Type:	Configuration
Format:	AT [cmds] -SEC=n [cmds]
Description:	Selects whether the modem will attempt to use MNP10EC mode during the handshaking sequence.
Command		Function
-SEC=0		MNP10EC handshaking disabled unless a V.34 connection is attempted via a cellular line.
í -SEC=1		MNP10EC handshaking enabled.

RESULT CODES
Type:	Configuration
Format:	AT [cmds] Qn [cmds]
Description:	Enables modem to send result codes to the DTE.
Command	Function
í Q0	Result codes enabled.
Q1	Result codes disabled.
Q2	Result codes enabled in originate mode only.

TRELLIS CODING
Type:	Configuration
Format:	AT [cmds] &Un [cmds]
Description:	Selects whether the modem will use trellis coding.
Command		Function
í &U0		Trellis coding enabled.
&U1		Trellis coding disabled.