THINFAX 1414I, THINFAX 1414C modem/telephone/ISDN Settings and Configuration

EXP COMPUTER, INC.

THINFAX 1414I, THINFAX 1414C

Card Type
Modem (synchronous/asynchronous)
Chipset
Unidentified
Maximum Data Rate
14.4Kbps
Maximum Fax Rate
14.4Kbps
Data Modulation
Bell 103A/212A
ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis
Fax Modulation
ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression
MNP5, MNP10, V.42, V.42bis
Fax Class
Class I & II
Data Bus
PCMCIA Type II

EXP-COMPUTER-INC-Modem-synchronous-asynchronous-TH

SUPPORTED STANDARD COMMANDS
Basic AT Commands
+++, ‘comma’, A/
A, B, D, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z
&C, &D, &F, &G, &K, &L, &M, &P, &Q, &R, &S, &T, &V, &W, &X, &Y, &Z
Extended AT Commands
\A, \B, \G, \K, \L, \N
%C, %E, %L, %Q, %TT
Special AT Commands
:E, *H, -K, )M, @M, -Q
S-Registers
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25
S26, S27, S28, S29, S30, S31, S32, S33, S36, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92
S95, S99, S201
Note: See MHI help file for complete information.

UNIDENTIFIED COMMANDS
Command
Default
S37
0
S80
0

Proprietary AT Command Set

AUTOSYNC OPTIONS
Type:
Register
Format
AT [cmds] S19=n [cmds]
Default:
26
Range:
0 - 30
Description:
Controls autosync protocol, HDLC address detection, bit coding, and HDLC idle.
Bit
Value
Function
0
0
Not used
1
0
í 1
Binary synchronous protocol used.
HDLC protocol used.
2
í 0
1
HDLC address detect disabled.
HDLC address detect enabled.
3
0
í 1
NRZI bit coding used.
NRZ bit coding used.
4
0
í 1
HDLC idle sends MARK.
HDLC idle sends FLAG or SYNC.

AUTOSYNC HDLC ADDRESS
Type:
Register
Format:
AT [cmds] S20=n [cmds]
Default:
0
Range:
0-255
Unit:
Unidentified
Description:
Sets the HDLC address and binary synchronous character.

DISPLAY INFORMATION
Type:
Immediate
Format:
AT [cmds] In [cmds]
Description:
Displays information requested about the modem.
Command
Function
I0
Displays product identification code.
I1
Displays ROM checksum.
I2
Tests and displays ROM checksum result.
I3
Displays firmware model, revision, and interface type.
I4
Displays OEM response.
I5
Displays country code.
I6
Displays data pump model.

PROTOCOL/SPEED
Type:
Configuration
Format:
AT [cmds] Fn [cmds]
Description:
Selects the protocol and speed the modem will attempt to connect at.
Command
Function
F0
Auto-detect the highest common connect speed.
F1
Select V.21 or Bell 103 at 300bps speed.
F3
Select V.23 at 75/1200bps speed.
F4
Select V.22 or Bell 212A at 1200bps speed.
F5
Select V.22bis at 2400bps speed.
F6
Select V.32 or V.32bis at 4800bps speed.
F7
Select V.32bis at 7200bps speed.
F8
Select V.32bis or V.32 at 9600bps speed.
F9
Select V.32bis at 12Kbps speed.
F10
Select V.32bis at 14.4Kbps speed.

REMOTE CONFIGURATION CHARACTER
Type:
Register
Format:
AT [cmds] S202=n [cmds]
Default:
170
Range:
0 - 255
Unit:
1 ASCII character
Description:
Defines the character that, when sent four times within the guard time set by S12, will notify the remote modem that a remote configuration session has been requested. Values over 127 disables the remote configuration character.

Headaches Begone! A Systemic Approach To Healing Your Headaches

Don't Let Your Bike Seat Ruin Your Sex Life Book

THINFAX 1414I, THINFAX 1414C modem/telephone/ISDN Settings and Configuration

Search

My Books

Discover

Card Type	Modem (synchronous/asynchronous)
Chipset	Unidentified
Maximum Data Rate	14.4Kbps
Maximum Fax Rate	14.4Kbps
Data Modulation	Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis
Fax Modulation	ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression	MNP5, MNP10, V.42, V.42bis
Fax Class	Class I & II
Data Bus	PCMCIA Type II

AUTOSYNC OPTIONS
Type:		Register
Format		AT [cmds] S19=n [cmds]
Default:		26
Range:		0 - 30
Description:		Controls autosync protocol, HDLC address detection, bit coding, and HDLC idle.
Bit	Value	Function
0	0	Not used
1	0 í 1	Binary synchronous protocol used. HDLC protocol used.
2	í 0 1	HDLC address detect disabled. HDLC address detect enabled.
3	0 í 1	NRZI bit coding used. NRZ bit coding used.
4	0 í 1	HDLC idle sends MARK. HDLC idle sends FLAG or SYNC.

AUTOSYNC HDLC ADDRESS
Type:	Register
Format:	AT [cmds] S20=n [cmds]
Default:	0
Range:	0-255
Unit:	Unidentified
Description:	Sets the HDLC address and binary synchronous character.

DISPLAY INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested about the modem.
Command	Function
I0	Displays product identification code.
I1	Displays ROM checksum.
I2	Tests and displays ROM checksum result.
I3	Displays firmware model, revision, and interface type.
I4	Displays OEM response.
I5	Displays country code.
I6	Displays data pump model.

PROTOCOL/SPEED
Type:	Configuration
Format:	AT [cmds] Fn [cmds]
Description:	Selects the protocol and speed the modem will attempt to connect at.
Command	Function
F0	Auto-detect the highest common connect speed.
F1	Select V.21 or Bell 103 at 300bps speed.
F3	Select V.23 at 75/1200bps speed.
F4	Select V.22 or Bell 212A at 1200bps speed.
F5	Select V.22bis at 2400bps speed.
F6	Select V.32 or V.32bis at 4800bps speed.
F7	Select V.32bis at 7200bps speed.
F8	Select V.32bis or V.32 at 9600bps speed.
F9	Select V.32bis at 12Kbps speed.
F10	Select V.32bis at 14.4Kbps speed.

REMOTE CONFIGURATION CHARACTER
Type:	Register
Format:	AT [cmds] S202=n [cmds]
Default:	170
Range:	0 - 255
Unit:	1 ASCII character
Description:	Defines the character that, when sent four times within the guard time set by S12, will notify the remote modem that a remote configuration session has been requested. Values over 127 disables the remote configuration character.